Page 3
Please cut where indicated and insert the label into the plastic pocket on the spine of the binder. SKID-STEER SKID-STEER REPAIR REPAIR LS140, LS150 LS140, LS150 Vol. 1 Vol. 1 87036977 87036977 87036995 Find manuals at https://best-manuals.com...
Page 4
SECTION 00 - - GENERAL INFORMATION BOOK 1 - 87042550 CONTENTS Section Description Page Introduction ..............About Improvements .
Page 19
SECTION 55 - - ELECTRICAL SYSTEM BOOK 4 - 87036981 Chapter 1 - - Advanced Warning System, Circuits, Alternator, and Starter (Continued) CONTENTS Section Description Page 55 414 10 Engine Coolant Temperature Sender Removal ....... 55-104 Engine Coolant Temperature Sender Installation .
Page 20
SECTION 55 - - ELECTRICAL SYSTEM BOOK 4 - 87036981 Chapter 1 - - Advanced Warning System, Circuits, Alternator, and Starter (Continued) CONTENTS Section Description Page Starter Inspection and Repair ..........55-152 Starter Reassembly .
Page 21
SECTION 82 - - FRONT LOADER (Boom And Mounting Plate) BOOK 4 - 87036981 Chapter 1 - - Buckets CONTENTS Section Description Page 82 100 General Information ............82-2 Buckets .
Page 22
SECTION 88 - - ACCESSORIES BOOK 4 - 87036981 Chapter 1 - - Dealer Installed Options CONTENTS Section Description Page 88 100 General Information ............88-2 Adapting Attachments Requiring 12V Electrical Power .
Page 23
LS140 LS150 Section 00 -- General Information Section 10 -- Engine 1/04 87042550...
Page 24
Each book will be labeled as to which sections are in the overall Repair manual and which sections are in each book. The sections listed above are the sections utilized for the LS140, LS150 Skid Steer.
Holland service parts from your New Holland dealer. the Models LS140 and LS150 skid steers. Use it in Be prepared to give your dealer the model and serial conjunction with the operator’s manual which is number of the engine and skid steer (the location of supplied with the skid steer.
We would like to point out that “NON-GENUINE” parts and accessories have not been examined and released by NEW HOLLAND. The installation and or use of such products could have negative effects upon the design characteristics of your machine and thereby affect its safety. NEW HOLLAND is not liable for any damage caused by the use of “NON-GENUINE”...
SECTION 00 - GENERAL INFORMATION PRECAUTIONARY STATEMENTS PERSONAL SAFETY MACHINE SAFETY Throughout this manual and on machine decals, you Additional precautionary statement (“IMPORTANT”) will find precautionary statements (“CAUTION”, is followed by specific instructions. This statement is “WARNING”, and “DANGER”) followed by specific intended for machine safety.
SECTION 00 - GENERAL INFORMATION SAFETY PRECAUTION INFORMATION CAUTION to the eic and prevent damage to the eic board or blowing the 5-amp fuses if the board Unsafe operating practices and improper use of is accidentally grounded. the skid steer and its attachments on the part of the operator can result in injuries.
Page 30
39. Keep the skid steer clean. do not allow trash, DANGER debris or other articles to accumulate in the...
SECTION 00 - GENERAL INFORMATION GENERAL SAFETY INFORMATION Check for leaks with a piece of cardboard. Protect hands and body from high-pressure fluids. HANDLE FLUIDS SAFELY When you work around fuel or other flammable If an accident occurs, see a doctor immediately. Any material, do not smoke or work near heaters or other fluid injected into the skin must be surgically removed fire hazards.
Page 32
SECTION 00 - GENERAL INFORMATION WARNING If servicing requires the engine to be operated, raise the machine and properly support the unit with Starting an engine with a booster battery adequate jack stands or blocking with all four wheels requires extreme care as batteries produce off the ground.
SECTION 00 - GENERAL INFORMATION MACHINE MODEL AND SERIAL NUMBER LOCATION The skid steer model and serial number tag is located on the right front interior of the operator’s cab at 1. ENGINE MODEL AND SERIAL NUMBER LOCATION The engine model and serial number is located on the left side of the block at 1.
Page 34
SECTION 00 - GENERAL INFORMATION MINIMUM HARDWARE TIGHTENING TORQUES IN FOOT POUNDS (NEWTON-METERS) FOR NORMAL ASSEMBLY APPLICATIONS INCH HARDWARE AND LOCKNUTS SAE GRADE 2 SAE GRADE 5 SAE GRADE 8 LOCKNUTS NOMINAL UNPLATED PLATED UNPLATED PLATED UNPLATED PLATED GR.B GR.C NOMINAL SIZE W/ZnCr...
Page 35
SECTION 00 - GENERAL INFORMATION MINIMUM HARDWARE TIGHTENING TORQUES IN FOOT POUNDS (NEWTON-METERS) FOR NORMAL ASSEMBLY APPLICATIONS METRIC HARDWARE AND LOCKNUTS CLASS 5.8 CLASS 8.8 CLASS 10.9 LOCKNUT NOMINAL CL.8 SIZE UNPLATED PLATED UNPLATED PLATED UNPLATED PLATED W/CL8.8 W/ZnCr W/ZnCr W/ZnCr BOLT 15* (1.7)
SECTION 00 - GENERAL INFORMATION INSTALLATION OF ADJUSTABLE FITTINGS IN STRAIGHT THREAD O RING BOSSES 1. Lubricate the O ring by coating it with a light oil or petroleum. Install the O ring in the groove adjacent to the metal backup washer which is assembled at the extreme end of the groove, 4.
1/2″ -- 14 41 N⋅m (30 ft. lbs.) 3/4″ -- 14 54 N⋅m (40 ft. lbs.) LUBRICANTS AND COOLANTS Application New Holland Part Number Specification Final Drive chain case 1 qt. - #9613313 API Service SH-CG4 10W-30 2.5 gal. - #9613314...
SECTION 00 - GENERAL INFORMATION PROPERLY SUPPORT A RAISED MACHINE If servicing neutral adjustment, final drive adjustment or repairs requiring the machine to be raised, securely support the machine with adequate jack stands or blocks as shown. Support the machine at 1 to the front of the final drive cases and to the rear at 2, making sure the supports are on the flat area of the final drive cases.
SECTION 00 - GENERAL INFORMATION 3. Attach a fork lift or overhead hoist to the main boom, 1 and lifting device, 2. Attach chain or strap securely to prevent unhooking during boom lifting. CAUTION Attach suitable chains or straps capable of handling the weight of the boom, 454 kg (1000 lbs).
Page 40
SECTION 00 - GENERAL INFORMATION 3. Attach a fork lift or overhead hoist to the main boom, 1 and lifting device, 2. Attach chain or strap securely to prevent unhooking during boom lifting. CAUTION Attach suitable chains or straps capable of handling the weight of the boom, 454 kg (1000 lbs).
Page 41
This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...