Adjusting The Z-Enhancer; Adjusting The Bass And Treble; Adjusting The Balance And Fader; Turning On/Off The Loudness - Clarion VRX610 Owner's Manual & Installation Manual

Basic Operations
When the panel is closed:
Each time you press the Z-EHCR button 9, the
tone effect changes in the following order:
"Z-EHCR 1" "Z-EHCR 2" "Z-EHCR 3"
"Z-EHCR OFF" "Z-EHCR 1"...
When the panel is open:
1. Press the A-M button & to change into the
AUDIO-MODE display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select "Z-EHCR". Press the ENT at
the center of the JOYSTICK ¡ to change into
the Z-enhancer selecting display.
3. Operate the JOYSTICK ¡ upward or down-
ward to select out of:
"TYPE 1" (Z-Enhancer 1) "TYPE 2" (Z-En-
hancer 2) "TYPE 3" (Z-Enhancer 3)
"OFF" (Z-Enhancer off),
and press the ENT at the center of the JOY-
STICK ¡ to set a desired Z-enhancer.
4. When the setting is finished, operate the JOY-
STICK ¡ rightward or leftward to move the
cursor to the "MENU". Then press the ENT at
the center of the JOYSTICK ¡ to return to
the AUDIO-MODE display.
To return from the AUDIO-MODE display to the
STANDARD display, press the A-M button &
once again.

Adjusting the Z-enhancer

Note:
• This function is enabled only when the panel is
open.
1. Press the A-M button & to change into the
AUDIO-MODE display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select "Z-EH LVL" level. Press the ENT
at the center of the JOYSTICK ¡ to change
into the Z-enhancer adjusting display.
3. Operate the JOYSTICK ¡ upward or down-
ward to adjust the Z-enhancer level.
When Z-Enhancer 1 is selected, you can adjust
the bass in the range of 2.
When Z-Enhancer 2 is selected, you can adjust
the treble in the range of 2.
When Z-Enhancer 3 is selected, you can adjust
the bass and treble in the range of 2.
4. When the adjustment is finished, operate the
JOYSTICK ¡ rightward or leftward to move
the cursor to "MENU". Then press the ENT at
the center of the JOYSTICK ¡ to return to
the AUDIO-MODE display.
18
VRX610

Adjusting the bass and treble

Notes:
• This function is enabled only when the panel is
open.
• This function can be adjusted only when the Z-
enhancer is OFF.
1. Press the A-M button & to change into the
AUDIO-MODE display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select "BAS/TRE". Then press the
ENT at the center of the JOYSTICK ¡ to
change into the BASS/TREBLE adjusting dis-
play.
3. Operate the JOYSTICK ¡ rightward or left-
ward to adjust the "BASS" or "TREBLE".
4. Operate the JOYSTICK ¡ upward or down-
ward to adjust a level (adjustment range: from
-6 to 6).
5. When the adjustment is finished, operate the
JOYSTICK ¡ rightward or leftward to move
the cursor to "MENU". Then press the ENT at
the center of the JOYSTICK ¡ to return to
the AUDIO-MODE display.

Adjusting the balance and fader

Note:
• This function is enabled only when the panel is
open.
1. Press the A-M button & to change into the
AUDIO-MODE display.
2. Operate the JOYSTICK ¡ upward or down-
ward to select "BAL/FAD". Then press the
ENT at the center of the JOYSTICK ¡ to
change into the BAL/FAD adjusting display.
3. Operate the JOYSTICK ¡ rightward or left-
ward to select "BALANCE" or "FADER".
4. Operate the JOYSTICK ¡ upward or down-
ward to make an adjustment.
Adjusting range of the balance: L13 to R13
Adjusting range of the fader: front 12 / rear 12
5. When the adjustment is finished, operate the
JOYSTICK ¡ rightward or leftward to move
the cursor to "MENU". Then press the ENT at
the center of the JOYSTICK ¡ to return to
the AUDIO-MODE display.

Turning on/off the loudness

The loudness effect emphasizes the bass and
treble to create a natural sound tone. When you
are listening to music at a low volume, it is rec-
ommended to use the loudness effect.
This function is enabled only when the panel is
open.
1. Press the A-M button & for 1 second or longer
to select Loudness ON. The "LD" indicator
lights in the display.
2. Press the A-M button & for 1 second or longer
to select Loudness OFF. The "LD" indicator
goes off.
Note:
• When using a sold separately digital sound processor
(DPH7500z/7700z), a feature called auto loudness is
selected. This function is different from the loudness
effect. For further details on the auto loudness feature,
refer to the subsection "Output adjustment of auto
loudness, subwoofer and playback band".
Basic Operations
19
VRX610