Power - Panasonic SA-MAX4000PN Service Manual

7.2.

Power

Reset Method Reset Method ( (Factory Shipment Status)
1. Plug In AC cord together with (no 2).
2. Press and hold the power button for 4 seconds then FL display will show RESET for 2 seconds.
3. Turn off the power.
Main set power ON Power do not turn ON
(No FL display)
Power input but turn off immediately
Power input but FL display error
Fuse cut After replacement, cut again at outlet connection
After replacement, cut again at power on
FL display checking Check the all segments display by Doctor Mode
Key operation checking Power on unit using remote control or power button
NFC checking Power on unit using remote control or power button
Figure 1-1
1
2
2
3
.
Power ON by remote control OK Check the 30P FFC connection from Button Left P.C.B (P1500) to Main PCB (CN2506)
Check the 22P FFC connection from Button Left P.C.B (P1502) to Multi Control PCB (P1600)
Check the 13P FFC connection from Multi Control P.C.B (P1601) to FL Display PCB (P1700)
Tact switch operation check (S1500)
Power ON by remote control NG Check the 30P FFC connection from Button Left P.C.B (P1500) to Main PCB (CN2506)
Check the 22P FFC connection from Button Left P.C.B (P1502) to Multi Control PCB (P1600)
Check the 13P FFC connection from Multi Control P.C.B (P1601) to FL Display PCB (P1700)
IR sensor operation check (IR1730).
Check the power supply output of SMPS Module to Main P.C.B
Check the AC inlet and AC cord
Check fuse cut
Error contents F76 Power off the unit during FL blinking of F76 (250ms ON/250ms OFF).
Error contents F61 Power off the unit during FL blinking of F61(250ms ON/250ms OFF).
Error contents F70 BT Check Connection of Bluetooth
The primary side of main power supply abnormal Check the continuity of primary side power circuit
The secondary side of main power supply abnormal Check the continuity of secondary side power circuit
Some FL segment not lighting Failure of FL Display (DP1700 & DP1800)
FL display "Hello" Press key buttons on unit
Press selector and choose "Bluetooth" Check and do setting of NFC. Off the set and tap phone on NFC logo on unit
Set will be on at Bluetooth mode
Figure 1-2
5
6 7
Check standby supply PW_SYS3R3V = +3.3V
Voltage check across the power switch. When button PCB power switch S1500 is press
Voltage check 1) +F to -F (filament voltage across FL pin 1 to pin 44),PW_VEE
Voltage check of IC2103 Pin 10 Output of L2101 = +12V (Refer Check Point 7 in Figure 1-1)
Voltage check of IC2108 Pin 2 = 3.3V (Refer Check Point 5 in Figure 1-1)
Voltage check of IC2101 and L2102 = 5.3V (Refer Check Point 6 in Figure 1-1)
Voltage check of IC2103 Pin 10 Output of L2101 = +12V (Refer Check Point 7 in Figure 1-1)
Voltage check of connection between Main P.C.B and SMPS Module. Replace SMPS Module if defective
Checking point for SMPS Module
C1/C1 at 200V or more, C40/D25 at +5V, C9/C22 at 38V or more
Check each DC supply output voltage (eg +40V, +15V, +12V, +5V, +3.3V,+1.8V)
Check the Fan Connection.
Check the IC overcurrent overheating failure of [Digital Amplifier]
(IC3001, IC3101, IC3201, IC3301)
[Main] BT & communication error of the microcomputer
Change SMPS Module
Check each DC supply output voltage (eg +40V, +15V, +12V, +5V, +3.3V,+1.8V)
Change to a new FL Display (DP1700 & DP1800) on the FL Display PCB.
Change button when not working properly
Check IC2101 and L2102 at 5.3V. Replace IC if defective
if set on and after taping NFC -> NFC not working, replace new NFC P.C.B
22
0V, release 3.3V to 3.5V
[Digital Amplifier] exchange
Check Main P.C.B and BT Module.