Advertisement
Failure t o properly configure t he GPI O Port can result in dam age t o t he print er and / or connect ed devices.
W ARN I N G
Signa l
Pin
D ir e ct ion
N a m e
1
Ground
N/ A
2
+ 5 VDC
[ 2]
3
St art Of Print
4
Slew Label
I nput
5
Toggle / Pause
6
Reprint
7
+ 24 VDC
N/ A
8
Ground
9
Ribbon Low
10
Service Required
11
End Of Print
12
Media Out
Out put
13
Ribbon Out
14
Dat a Ready
15
Opt ion Fault
[ 1]
Signal direct ions given relat ive t o t he print er.
[ 2]
I f act ive wit h no current print j ob, " WAI TI NG FOR DATA" will be displayed. Specifying a quant it y of 9999 while keeping t his signal ON will cause non- st op label print ing, except
in single label " I m aging Mode" , which will cause t he print er t o st op bet ween labels. See t he Operat or's Manual for det ails.
[ 3]
For det ails see PRI NTER OPTI ONS / GPI O PORT in t he Operat or's Manual.
GPI / O Por t A Jum pe r Ove r vie w
[ 1]
Ju m pe r
Posit ion
I nst alled
JMP 8
Rem oved
I nst alled
JMP 9
Rem oved
N/ A
N/ A
When inact ive, out put s will be
pulled up t o a volt age
det erm ined by t his j um per
set t ing, where:
Pins 1 – 2 = + 5VDC;
JMP 1
Pins 2 – 3 = + 24VDC; or,
None = an ext ernal volt age
( not t o exceed + 30VDC) via
ext ernal pull- ups providing a
20K ohm feedback pat h
t hrough any t wo out put s.
Fu n ct ion / D e scr ipt ion
Print er chassis is used.
Ground m ust be supplied.
Print er + 5VDC is used ( .5 am p m axim um )
N ot e : Drawing m ore t han .5 am ps can cause unreliable print er operat ion.
+ 5VDC m ust be supplied.
[ 3]
Program m able
Media is advanced unt il t he signal goes HI GH and, if not in cont inuous m ode, t he label
is posit ioned at t he next available TOF.
The print er pauses when t he signal is t aken LOW.
The last label is reprint ed exact ly, wit h no increm ent or t im e st am p changes;
recom m ended for use during error condit ions. Keeping t his signal LOW produces non-
st op print ing.
Print er + 24 VDC ( 1.5 am p m axim um ) .
Print er chassis.
[ 1]
Program m able
. Signifies a RI BBON LOW DI AMETER warning condit ion.
Evoked by occurrences list ed under 'Fault Messages.'
[ 1]
Program m able
. Signifies t he End of Print ( EOP) process.
Evoked during an Out of St ock condit ion. Act ive LOW.
Evoked during an Out of Ribbon condit ion. Act ive LOW.
Evoked when a label is wait ing t o print . Aft er St art of Print is received, print ing will begin.
For synchronizat ion wit h t he print cycle, End Of Print indicat es t he com plet ion of t he
process. Act ive LOW.
Evoked during a Linear Scanner or RFI D fault condit ion. Act ive LOW.
5
[ 1]
Act ive LOW.
Advertisement
