Advertisement
Quick Links
Advertisement
Related Manuals for Datamax H-Class GPI O Option
Summary of Contents for Datamax H-Class GPI O Option
- Page 1 92-2427-01 Rev.C GPI O Opt ion...
- Page 3 Ove r vie w This docum ent describes t he inst allat ion and use of t he General Purpose I nput Out put ( GPI O) opt ion for t he H- Class print er. Aft er verifying t he kit cont ent s and t ools needed, follow t he st eps t o inst all and begin using t he opt ion.
- Page 4 COM C RS- 2 3 2 Ca ble s Part # 32- 2300- 01 Part # 32- 2301- 01 COM D RS- 2 3 2 Ca ble Host DB- 9S Print er RJ45P +5 VDC +5 VDC GROUND GROUND Part # 32- 2603- 00...
- Page 5 St e p 1 : Con figu r in g t h e H a r dw a r e Configure t he card t o m eet your int erfacing requirem ent s by arranging hardware j um pers, as described in t he following procedure: Always wear a wrist st rap and follow st andard ESD prevent ion m easures when handling t he card.
- Page 6 GPI/O A - J1 For dir e ct in pu t s – Start of Print Use t he print er’s + 5VDC and Ground t o supply Slew Label t he devices int erfacing t o t he GPI / O A input s Toggle/Pause ( as shown in t he sam ple circuit , right ) .
- Page 7 Failure t o properly configure t he GPI O Port can result in dam age t o t he print er and / or connect ed devices. W ARN I N G GPI / O Por t A Jum pe r Ove r vie w Signa l [ 1] D ir e ct ion...
- Page 8 ► GPI / O B ( J2 ) Six u n a ssign e d in pu t s are designed t o int erface t o open- collect or out put s. These input s require no ext ernal pull- ups, while blocking diodes allow t he use of t ot em pole out put s from + 4.5 VDC t o + 26 VDC.
- Page 9 Failure t o properly configure t he GPI O Port can result in dam age t o t he print er and / or connect ed devices. W ARN I N G GPI / O Por t B Ove r vie w [ 1] Sign a l N a m e / D ir e ct ion Ju m pe r...
- Page 10 ► COM C ( J4 ) Recognized by t he print er as Serial Port C, COM C funct ions as an auxiliary RS- 232 int erface or dedicat ed device port for t he RFI D and Linear Scanner opt ions. Pin assignm ent s for t he port are as follows: Pin N u m be r COM C ( J4 )
- Page 11 St e p 2 : I n st a llin g t h e Opt ion I nst all t he GPI O Card as described below: A) Turn OFF t he Pow e r Sw it ch and unplug t he power cord from t he AC Power Switch Re ce pt a cle .
- Page 12 Card Cage Cover Plate D ) Place t he Cove r Pla t e ( I t em 2) ont o Screws t he Ca r d Ca ge , as shown, t hen inst all and t ight en t he t wo Scr e w s ( I t em 3) t o secure t he plat e.
- Page 13 St e p 4 : Con figu r in g t h e Soft w a r e Se t t in gs Configure t he print er’s m for t he opt ion’s operat ion. enu set t ings A) Using t he Cont rol Panel, ent er t he AD VAN CED M EN U ( see t he Operat or’s Manual for m enu navigat ion det ails) : •...
- Page 14 I n pu t M on it or – Display incom ing GPI O binary signal st at es using t he AD VAN CED M EN U D I AGN OSTI CS OPTI ON S TESTI N G TEST GPI O M ON I TOR GPI O I N PUT select ion.