Table of Contents
Advertisement
All manuals and user guides at all-guides.com
17
Disc Change
You can change the outer two discs
while the third inner disc is stopped or
is playing.
1 Press DISC CHANGE.
™ The CD carousel tray slides out.
2 Replace the discs in the left and right
disc trays.
• If you wish to change the inner disc
during playback, press DISC
CHANGE again.
™ "DISC CHANGE" will be
displayed.
™ The CD will stop playing.
™ The CD carousel tray will close to
retrieve the inner CD and then
open again with the inner CD
accessible.
3 Press OPEN•CLOSE to close the
CD carousel tray.
Selecting a desired track
Selecting a desired track when
playback is stopped
1 Press í or ë (or Digit 0-9 on the
remote control) until the desired track
appears on the display.
2 Press PLAYÉ Å to start playback.
™ The selected track number and
elapsed playing time appear on
the display.
pg 01-28/C85/37-Eng
17
CD
Selecting a desired track during
Programming Tracks
playback
Programming tracks of a loaded CD is
• Press í or ë (or Digit 0-9 on the
possible when playback is stopped. The
remote control) until the desired track
display will indicate the total tracks
appears on the display.
stored in the program. Up to 40 tracks
™ The selected track number and
can be stored in the memory in any
elapsed playing time appear on
order. When 40 tracks are stored and
the display.
you attempt to store another track, the
• If you press í once it will skip to
display will show "PROGRAM FULL".
the beginning of the current track
and play the track again.
1 Load the desired discs in the disc
trays.
Note:
2 Press PROG to start programming.
– Pressing í during shuffling can only
™ The
skip to the beginning of the current
™ It will cancel any previously
track.
3 Press the CD (CD 1•2•3) or DISC
Searching for a particular
1/2/3 button to select the disc.
passage during playback
4 Press í or ë (or Digit 0-9 on the
remote control) to select the desired
• Press and hold à or á until the
track.
desired passage is located.
5 Press PROG to store the track.
™ The volume will be reduced.
• Repeat steps 3 to 5 to store other
• Play returns to normal when à or
discs and tracks.
á is released.
6 Press Ç once to end programming.
™ The total number of tracks
Notes:
– If the total playing time is more than
" 99:59 " or if one of the programmed
tracks has a number greater than 30,
then " --:-- " appears on the display
instead of the total playing time.
– If the system is reading the disc,
programming is not possible,
"READING" will be displayed and
followed by "DISC X" "X" is the
current read disc number.
– During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
Reviewing the program
Reviewing of the program is possible
only when playback is stopped.
1 Press í or ë repeatedly to review
starts flashing.
PROGRAM
the programmed tracks.
2 Press Ç once to exit review mode.
selected repeat mode.
Playing the program
1 Press PLAYÉ Å to start program
playback.
™ "PLAY PROGRAM" will be
displayed.
™ The track number and elapsed
playing time of the current track
will appear on the display.
• If you press REPEAT during
programmed and total playing
program playback, the current track
time appear on the display.
or all programmed tracks will be
played repeatedly.
™ "TRACK" or "PROGRAM" will be
displayed.
™ The
on the display.
2 Press Ç to stop program playback.
2/16/00, 9:03 AM
and
appear
REPEAT
PROGRAM
3139 116 19591 (ENG)
Advertisement
Table of Contents
