AMX Modero Viewpoint MVP-5200i Installation Manual

Overview
The MVP-5200i Modero® Viewpoint® Widescreen Touch Panel is AMX's smallest and
most powerful wireless handheld panel, available in black (FG5966-03) and white
(FG5966-04). The MVP-5200i is a wireless-only ergonomic device capable of Voice
Over Internet Protocol (VoIP) communication, with all control established through a
NetLinx Master. Besides offering the same functionality as the rest of AMX's line of G4
touch panels, the MVP-5200i touch panel offers full duplex VoIP communication, quick
wakeup and connection time, and an extended battery life for longer operation
between charges. The MVP-5200i device utilizes a 5.0" (12.59 cm) Color Active LCD
to display a 800 x 480 pixel image with 16M colors and 24-bit color depth.
The MVP-5200i comes with an integrated rear "kickstand", allowing it to be used and
displayed away from a docking station if necessary. It also comes with a pre-installed
802.11g WPA/WPA2 SDIO wireless card.
For detailed installation, configuration, programming, file transfer, and operating
instructions refer to the MVP-5200i Modero ViewPoint Touch Panel Operation/
Reference Guide, available online at www.amx.com.
Microphone
FIG. 1 MVP-5200i-GB touch panel
FCC Statement
This device complies with FCC Part 15 and Industry Canada RSS 210 subject to the
following conditions:
1. This device must not cause harmful interference and
2. This device must accept all interference, including interference that interferes
with the operation of this device.
Specifications
MVP-5200i Specifications
Dimensions: 4 3/4" x 7 9/16" x 13/16" (120.7 mm x 191.8 mm x 20.3
mm)
Weight: • Panel: 1.4 lbs (0.64 kg)
Power Requirements Panel with battery fully charged or with no battery:
(Without Charging):
• Constant current draw: 0.32 A @ 12 VDC
• Startup current draw: 0.35 A @ 12 VDC
Power Requirements Panel while charging battery:
(While Charging):
• Constant current draw: 1.06 A @ 12 VDC
• Startup current draw: 1.08 A @ 12 VDC
Minimum Power Supply PS3.0 Power Supply (FG423-30) - both 120 VAC and 240
Required: VAC models are shipped with this power supply.
Power Modes: • ON: All necessary modules are powered up and device
remains online with the NetLinx Master.
• SLEEP: Only the backlight will be turned off after the
user selectable time of inactivity has elapsed. Panel
resumes the ON mode in ~ 1 second after being
touched.
• STANDBY: Power to all components other than the
touch screen is turned off after the user selectable time
of inactivity has elapsed. Device will turn back on by
touching the screen. Re-acquiring an AP connection
may require up to 10 seconds.
• SHUTDOWN: Power to all peripherals and components
is turned off. The system remains in this mode until it is
rebooted.
Battery Duration: • On mode – 5.1 hours of battery life
• Sleep mode – 8.5 hours of battery life
Memory: • 128 MB Mobile DDRAM (upgrade not available)
• 256 MB NAND Flash (upgrade not available)
MVP-5200i
Navigation Wheel LED
Navigation
Wheel
Touch Screen
Speaker Grille
®
5" Modero Viewpoint
MVP-5200i Specifications (Cont.)
Screen Properties: • Screen resolution: 800 x 480 pixels (HV) @ 60 Hz frame
frequency
• Screen type: WVGA
• Aspect ratio: 16 x 9
• Brightness (luminance): 300 cd/m
• Channel transparency: 8-bit Alpha blending
• Contrast ratio: 600:1
• Display colors: 16M colors (24-bit color depth)
• Dot/pixel pitch: 0.135 x 0.135 mm
• Panel type: TFT Color Active-Matrix
• Viewing Angle (Up/Down/Left/Right):
Vertical: + 50° (up from center) and - 70° (down from
center)
Horizontal: + 70° (left from center) and - 70° (right from
center)
External Components
5-pin Mini-USB connector used for output to USB 
Connector:
headphones, programming, firmware update, and touch
panel file transfer between the PC and the target panel.
Note: When connecting the panel to PC using a CC-USB
(or compatible) cable, be sure to power the panel On
before attempting to connect the USB cable from the PC
to the mini-USB port on the panel.
Internal Components:
IR Emitters: Transmit IR over 20 feet (6.10 m) from the panel.
• IR emitters on G4 panels share the device address
number of the panel.
• Transmits AMX fixed frequencies at 38KHz and 455KHz
and user programmable frequencies from 20KHz to
1.5MHz
Certifications: • FCC Part 15 Class B
• CE
• IEC/EN-60950
• RoHS
• Japan Approved
• Lithium polymer microbattery: UN/IATA
Operating/Storage 
• Operating Temperature: 0° C (32° F) to 40° C (104° F)
Environment
• Operating Humidity: 20% - 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
Included Accessories: • Installation Guide (93-5966-01)
• PS3.0 Power Supply (FG423-30)
• MVP-STYLUS-52 (pre-installed onto the right side of the
unit) (FG5966-06XX)
Other AMX Equipment: • MVP-TCS-52: Table Charging Station (FG5966-1X)
• MVP-WCS-52: Wall Charging Station (FG5966-1X)
• MVP-BP-5X: Battery Pack Kit (FG5966-27)
• MVP-STYLUS-52: Replacement Stylus, Pack of 3
(FG5966-2X)
• CC-USB: USB Programming Cable (FG10-5965)
• MVP-HPUSB 1/8" Adapter (FG5966-23)
Table Charging Station Connector Locations
Front
FIG. 2 MVP-5200i Connector Locations
With the unit facing you, the mini-USB port (for programming and downloading
firmware, as well as connecting USB headphones using the AMX-provided adaptor
cable) and the DC power jack are located on the lower left side of the device. The
connector for the Table Charging Station is located on the bottom of the device.
Installation Guide
®
Widescreen Touch Panel
2
DC power jack
Mini-USB port
Charging Station
Connector