Breville 800ES Manual page 10

NOTE: When the 800ES is creating
steam a pumping noise can be
heard. This is the normal
operation of the 15 Bar pump.
• When the red 'Heating' light stops flashing,
quickly insert the Steam Wand into the jug of
milk so that the Froth Attachment is just
immersed into the milk.
NOTE: If steam starts coming from
the Steam Wand before it is
immersed in the milk, pause the
• Hold the frothing jug at an angle so that the
steam by turning the Selector Frothing Attachment sits just below the
surface of the heating milk and the steam will
Control back to the 'Standby'
move the milk around the inside of the jug in
position. This will avoid the
a circular motion.
steam pressure blowing milk
out of the jug.
NOTE: The 800ES features a Swivel
18
HOW TO FROTH MILK FOR A CAPPUCCINO OR LATTÉ
• When the milk starts to increase in volume,
immerse the Frothing Attachment deeper into
the jug to heat the milk.
• Hold the jug at an angle with one hand and
place your other hand on the outer base of
the stainless frothing jug.
• When the base of the jug becomes too hot to
touch, set the Selector Control to the
'Standby' position, stopping the steaming
function before removing the jug. A pumping
noise will sound for a short time, do not be
alarmed as there will be a five second delay
prior to the machine carrying out the Auto-
purge function.
• Pour the steamed milk into each cup of
freshly brewed espresso coffee and spoon in
the frothed milk, in the following ratios:
Cappuccino - 1 / espresso,
3
1 / frothed milk
3
Latté - 1 / espresso topped with steamed milk
3
and about 1cm of frothed milk, traditionally
served in a glass)
Steam Wand assembly so
the position of the Steam
Wand can be changed to a
comfortable angle.
STEAM BUTTON/HOT WATER BUTTON
• The Steam button surround will automatically
illuminate after the machine has first reached
the correct temperature.
• The machine will always automatically default
to the Steam button when the appliance is
first switched on.
• Both buttons cannot be operated at the same
time.
• To select steam: when the Steam button
surround is illuminated, just set the Selector
Control to 'Steam'
• To select hot water: press the Hot Water
button and the surround will illuminate, then
just set the Selector Control to 'Steam'.
• If the machine remains switched 'On', the last
1 / steamed milk,
button function used (Steam or Hot Water)
3
will stay illuminated.
WARNING: MILK SHOULD NOT BE ALLOWED TO RUN OVER THE TOP OF THE FROTHING
ATTACHMENT, OTHERWISE IT WILL NOT FUNCTION PROPERLY.
TO AVOID SPLATTERING OF HOT MILK, DO NOT LIFT THE END OF THE FROTHING
ATTACHMENT ABOVE THE SURFACE OF THE MILK
WHILE FROTHING.
ENSURE THE SELECTOR CONTROL IS IN THE 'STANDBY' POSITION BEFORE
REMOVING THE FROTHING JUG.
NOTE: Always ensure that the NOTE: For brewing more coffee
Frothing Attachment has been immediately after using the
firmly pushed onto the Steam steam function, the 800ES
Wand and connects with the features an auto-purge function.
rubber surround. This ensures that ground coffee
will not be burnt by the initial
For best results use cold fresh
water flow from the thermoblock
milk (low fat milk will froth easier)
that could be too hot. Instead
Always clean the Steam Wand
this water is automatically
and Frothing Attachment after
released internally into the Drip
every use. Refer to Care and
Tray ensuring that the internal
Cleaning on Page 20.
thermostat is at optimal
temperature for extracting
coffee. Your coffee will always
be extracted at this optimal
temperature ensuring only
the best flavoured coffee
is achieved.
19
HOW TO FROTH MILK FOR A CAPPUCCINO OR LATTÉ