Notes On The Power Supply - Epson SC-R5000 Series Setup Manual

EN
Safety Instructions
If the LCD for the control panel is damaged, be careful of any leaking liquid crystal.
Provide first aid under any of the following conditions.
❏ If liquid adheres to your skin, immediately wipe it off and then wash the area using large
volumes of soapy water.
❏ If any liquid gets in your eyes, flush them with clean water for at least 15 minutes, and consult a
physician immediately.
❏ If liquid is swallowed, rinse your mouth out with water, swallow large quantities of water and
vomit it back up, and consult a physician immediately.
If any foreign objects or liquid such as water enters the printer, stop using it immediately.
An electric shock or fire could occur. Turn off the power and unplug the power cable immediately,
and then contact your dealer or Epson Support.
Do not sit on the product or place any heavy objects on the product.
The printer could tip over or break and cause an injury.
When transporting or storing the product, be sure that it is level: do not tilt it at an angle or
place it upside down.
Ink could leak.
Be careful not to trap your hands or fingers when opening or closing the
maintenance covers.
Failure to observe this precaution could result in injury.
When connecting cables or optional accessories, make sure they are installed in the correct
direction and that you follow the procedures exactly.
A fire or an injury could occur. Install the printer correctly by following the instructions in the
manual.
When moving the product, make sure it is turned off, the power cable is unplugged from the
outlet, and all connecting cables have been removed.
If cables are damaged, an electric shock or fire could occur.
See the manual to make sure the media and the roll core for the auto take-up reel unit are
secured correctly.
Dropping media or take-up rolls could result in injury.
Follow the instructions in the manual when removing media or take-up roll.
Dropping media or take-up rolls could result in injury.
Be sure that your hands or hair do not get caught in the media feeding unit or auto take-up reel
unit while it is operating.
Failure to observe this precaution could result in injury.
Except when moving the stand, make sure the two casters (wheels) at the front of the stand are
secured.
If they are not secured, an accident could occur.
6
!
Warning
!
Caution
printer cover and the
The curing heater, heaters and media edge plate may be hot; observe all necessary
precautions.
Failure to observe the necessary precautions could result in burns.
Do not reach inside the
Failure to observe the necessary precautions could result in burns.

Notes on the Power Supply

To prevent ground leak accidents, connect to a grounded (earthed) outlet.
Connecting to anything other than a grounded outlet could result in electric shock or fire.
Make sure the blades on the plug are inserted completely into the power outlet.
An electric shock or fire could occur.
Unplug the plug regularly and clean between the blades and around the base of the blades.
If the plug is plugged in for an extended period of time, dust collects around the base of the blades
and a short circuit or fire could occur.
When unplugging the plug, grip the plug itself; do not pull the power cable.
If the cable is damaged or the plug is deformed, an electric shock or fire could occur.
Do not insert or unplug the plug with wet hands.
An electric shock could occur.
Use only the type of power source indicated on the printer's label.
An electric shock or fire could occur.
Do not use the plug if any foreign objects such as dust have adhered to the plug.
An electric shock or fire could occur.
Do not use any other power cables except for the cable supplied with the printer. Also, do not
use the power cable supplied with the printer for any other devices.
An electric shock or fire could occur.
Do not use the power cable if it is damaged.
An electric shock or fire could occur. If the power cable is damaged, contact Epson Support. Note
the following points to avoid damaging the power cable.
❏ Do not modify the power cable.
❏ Do not place anything heavy on the power cable.
❏ Do not bend, twist, or pull forcefully on the power cable.
❏ Do not route the power cable near heaters.
!
Caution
curing heater.
!
Warning