Philips FW-C90 User Manual page 16

All manuals and user guides at all-guides.com
CD
Playing a CD
1 Press PLAYÉ Å to start playback.
™ The disc tray, track number and
elapsed playing time of the current
track appear on the display.
• To interrupt playback, press
PAUSEÉ Å .
™ The playing time flashes.
• To resume playback, press PLAYÉ Å
again.
2 To stop playback, press Ç.
Notes:
– All the available discs will play once,
then stop.
– When the CD has stopped playing, the
system will switch to standby mode
after 30 minutes if no button is pressed.
Disc Change
You can change the outer two discs while
the third inner disc is stopped or is playing.
1 Press DISC CHANGE.
™ The CD carousel tray slides out.
2 Replace the discs in the left and right
disc trays.
• If you wish to change the inner disc
during playback, press DISC CHANGE
again.
™ "DISC CHANGE" will be displayed.
™ The CD will stop playing.
™ The CD carousel tray will close to
retrieve the inner CD and then open
again with the inner CD accessible.
16
pg 01-29/C90/22-Eng 16
3 Press OPEN•CLOSE to close the CD
Searching for a particular
carousel tray.
passage during playback
• Press and hold à or á until the
Selecting a desired track
desired passage is located.
Selecting a desired track when
™ The volume will be reduced.
playback is stopped
• Play returns to normal when à or á
1 Press í or ë (or Digit 0-9 on the
is released.
remote control) until the desired track
appears on the display.
Programming Tracks
2 Press PLAYÉ Å to start playback.
Programming tracks of a loaded CD is
™ The selected track number and
possible when playback is stopped. The
elapsed playing time appear on the
display will indicate the total tracks stored
display.
in the program. Up to 40 tracks can be
stored in the memory in any order. When
Selecting a desired track during
40 tracks are stored and you attempt to
playback
store another track, the display will show
• Press í or ë (or Digit 0-9 on the
"PROGRAM FULL".
remote control) until the desired track
appears on the display.
1 Load the desired discs in the disc trays.
™ The selected track number and
2 Press PROG to start programming.
elapsed playing time appear on the
™ The
display.
™ It will cancel any previously selected
• If you press í once it will skip to the
beginning of the current track and play
3 Press the CD (CD 1•2•3) or DISC 1/2/3
the track again.
button to select the disc.
4 Press í or ë (or Digit 0-9 on the
Note:
remote control) to select the desired
– Pressing í during shuffling can only skip
track.
to the beginning of the current track.
5 Press PROG to store the track.
• Repeat steps 3 to 5 to store other discs
and tracks.
6 Press Ç once to end programming.
™ The total number of tracks
programmed and total playing time
appear on the display.
Notes:
– If the total playing time is more than
" 99:59 " or if one of the programmed
tracks has a number greater than 30,
then " --:-- " appears on the display
instead of the total playing time.
– If the system is reading the disc,
programming is not possible,
" READING " will be displayed and
followed by " DISC X " . " X " is the
current read disc number.
– During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
Reviewing the program
starts flashing.
PROGRAM
Reviewing of the program is possible only
when playback is stopped.
repeat mode.
1 Press í or ë repeatedly to review
the programmed tracks.
2 Press Ç once to exit review mode.
3/6/00, 1:53 PM
3139 116 19701