Table of Contents
Related Manuals for Schlage AD-201
Summary of Contents for Schlage AD-201
- Page 1 *P516-129* P516-129 AD-200 AD-201 Offline lock user guide Instructions for AD-Series offline locks Para el idioma español, navegue hacia www.schlage.com/support. Pour la portion française, veuillez consulter le site www.schlage.com/support.
-
Page 2: Table Of Contents
UL Listed product, in accordance with the requirements of the Standards UL 294 and ULC S319. This product has been evaluated for CAN/ULC-S319 Class 1. 2 • Schlage • AD-200 user guide... -
Page 3: Overview
Overview The Schlage AD-200/AD-201 is an off-line electronic lock in the AD-Series product line. The Schlage AD-201 is a FIPS-201 certified off-line electronic lock. • May be powered by batteries or connected to external power using a UL294 or ULC S318/ULC S319 listed power supply capable of sourcing at least 250 mA @ 12 or 24 VDC. -
Page 4: Getting Started
Save this user guide for future reference. Schlage Utility Software (SUS) The Schlage Utility Software is used for programming and setup only. The (SUS) is used to configure locks. This includes transferring data files between the access control software and locks. For information about the SUS, refer to the SUS user guide. -
Page 5: Construction Access Mode
PIN of 13579 and “#”, which can be used for installation, testing and construction access. To test, enter default PIN. The Schlage button will blink and the lock will unlock. The default PIN, 13579 and “#” is automatically deleted when a construction access user credential is added to the lock, or a new programming credential is created, or the lock is programmed with the SUS. -
Page 6: Manual Lock Programming
Left LED Right LED The Schlage button has two different LEDs, one on the left and one on the right. Press the Schlage button to activate the keypad backlight. All locks have a default programming code of 97531 and “... - Page 7 Schlage button, three left and nine right at the same time. An incorrect entry is indicated on the Schlage button by a solid red left LED, and a blinking green right LED. To interpret blink patterns, refer to Error codes on page 9.
- Page 8 Credential [PIN] between each delete another step. to finish credential 1 Other lights may show before the final confirmation. Wait for the final confirmation before continuing to the next step. 8 • Schlage • AD-200 user guide...
-
Page 9: Error Codes
1 Other lights may show before the final confirmation. Wait for the final confirmation before continuing to the next step. Error codes All error codes are indicated on the Schlage button by a solid red left LED, and a blinking green right LED. The number of green blinks indicates the error code. Number of... -
Page 10: Test Lock Operation
3. For locks with a card reader, present a credential to the reader. The lock will beep and the left side of the Schlage button will blink red one time. When the lock is in factory default mode, no credentials are accepted. -
Page 11: Normal Lock Operation
5. The Schlage button and IPB will both light green for one second and a one-second beep will be heard. This indicates that the lock has been reset. -
Page 12: Batteries
Solution Batteries low After credential is presented, 9 red Replace batteries immediately to avoid blinks of Schlage button. (Left = AA, battery failure. Lock is intended to Right = Coin Cell), then normal operate for 500 cycles in low battery indicator. -
Page 13: Battery Failure Modes
1 Fail Unlocked and Fail Locked modes are not available if the lock is externally powered. External power supply The AD-200/AD-201 may be connected to external power using a UL294 listed Power Supply for UL installations, and a power supply that complies with CAN/UL-S318 or CAN/ULC-S319 for cUL installations. -
Page 14: Led Reference
With door closed, press IPB to release 4 red blinks privacy 1 If DPS is used, then opening the door will also release privacy. If mortise deadbolt is used, then retracting the deadbolt will also release privacy. 14 • Schlage • AD-200 user guide... -
Page 15: Troubleshooting
The batteries may be the correct polarity. inserted with incorrect Refer to the installation instructions polarity. that came with the AD-200/AD-201 lock, or this user guide for details on the above mentioned procedures. The reader is not The through hole ribbon Check that the through hole ribbon working. -
Page 16: Fcc Statements
FCC Statements Allegion Agency Statements Compliance Statement (Part 15.19) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Customer Service ©...