Table of Contents
Advertisement
Innovative Hearth Products
DRT35ST and DRT35PF Direct-Vent Gas Fireplaces
Ground Wire
Connection
White
(supply)
Black
(supply)
NOTE: Supply wires may be alternatively con-
nected to the outlet using the screw terminals,
however the black supply wire must be wired to
a terminal that is opposite (across the outlet) the
point where the white supply wire is connected.
Figure 44
Receptacle, Junction Box
and Cover Plate Installation
Outlet Receptacle
Junction Box
View Of Left
Bottom Corner Of Unit
Metal Junction Box
Cover Plate With Screw
Junction Box
knock-out (2
places each side)
Press snap
bushing into the
knock-out for
control switch
wires.
Figure 45
30
Step 6. WIRING - OPTIONAL FORCED AIR
BLOWER KIT
FBK-100, FBK-200 and FBK-250 Kits
(See Figure 46 for wiring) -
An electrical receptacle is provided for the instal-
lation of the FBK-100, FBK-200 and FBK-250
forced air blower kits. Electrical power must be
connected to this receptacle in order to operate
Bipolar
these blowers.
Terminal
Screw
Latching magnet
not shown
Pilot Burner
Assembly
Fireplace
Side
Optional Control Switch
Electronic Wiring Diagram (Honeywell) Showing Blower Wiring for Optional FBK-100, FBK-200 & FBK-250 Kits
Figure 46
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Plug blower
Green
into this
receptacle
Blower
Ground
Tab Intact
Green
Neutral
Ground
Side of
Screw
Receptacle
View A
J-Box Wiring when
Relay Module C/W FBK-250 only. Plug blower
using unit mounted
into J-Box receptacle for FBK-100 or FBK-200
relay module.
application. See View A for J-Box wiring.
BK
W
G
Optional Blower
Junction Box
*OFF/ON Switch
(Integral with
Gas Valve)
Honeywell
Electronic
Gas
Valve
Igniter
Connector
BL
BL
BK
R
BK
BK
W
Schematic Representation Only
Installation and Operation Instructions
Install the blower kits according to the instal-
lation instructions provided with the kits. See
Figure 12 on Page 14 showing where blower
should be located on unit.
CAUTION
Remove the carton support from
the control compartment before
operating the appliance.
White
Black
Tab
Broken
Red
J-BOX WIRING FOR
Hot
WALL SWITCH
Side of
BLOWER CONTROL
Receptacle
* Leave the OFF/ON switch, which is
integral with the gas valve, in the ON
GROUND
position.
Transformer
**Optional Control Switches: Wall
Switch, Wall Thermostat or Remote
BL
Control Receiver.
24 V
120 VAC
Secondary
Notes:
Primary
1. If any of the original wire as supplied
must be replaced, use Type AWM 105°C
- 18 gage wire ONLY.
BK = BLACK BL = BLUE
2. 120 VAC, 60 Hz - Less than 3 Amps.
R = RED
W = WHITE
Caution: label all wires prior to
G = GREEN
disconnection when servicing controls.
Field Wired
Wiring errors can cause improper and
Factory
dangerous operation.
Wired
900300-00, 01/2019
G
o r
n u
- d
G
e r
n e
N
e
t u
a r
- l
W
h
e t i
120 VAC - Black
Junction Box
* Wall-mounted
ON/ OFF Blower
Switch or Variable
Speed Control Switch.
Advertisement
Table of Contents
