Genie Industries in the U.S.A. and many other countries. "GS" is a trademark of Genie Industries. These machines comply with ANSI/SIA 92.6-1999. Printed on recycled paper Printed in U.S.A. Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Manufacturer's instructions and safety rules—safety and operator's manuals and machine decals employer's safety rules and worksite regulations applicable governmental regulations You are properly trained to safely operate the machine. Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
Page 4
Do not operate the machine during lightning or storms. Do not use the machine as a ground for welding. Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Page 5
Maximum occupants - CE and Australia Outdoor use Indoor use only 700 lbs / 318 kg Extension only Platform only 250 lbs / 113 kg 450 lbs / 204 kg Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
Page 6
Australia - Indoor use only - 2 person 90 lbs / 400 N the surface area of the platform or the load. Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Page 8
Observe and use the color-coded direction arrows on the platform controls and platform decal plate for drive and steer functions. No stunt driving or horseplay while operating a machine. Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Page 9
An air leak or hydraulic leak can penetrate presence of a potentially and/or burn skin. hazardous situation which, if not avoided, may result in property damage. Green—used to indicate operation or maintenance information. Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
Page 10
The battery tray should remain open during the entire charging cycle. Do not contact the battery terminals or the cable clamps with tools that may cause sparks. Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
6 Key switch for platform/off/ 1 Auxiliary lowering/manual ground selection lowering toggle switch or 4 Breaker for electrical circuits knob or button 5 Platform up/down toggle 2 Hour meter switch Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Page 13
Emergency Stop button in upper left corner One function select button and Emergency Stop button in upper left corner Emergency Stop button in lower right corner Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
Scheduled maintenance inspections shall be performed by qualified service technicians, according to the manufacturer's specifications and the requirements listed in the responsibilities manual. Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Page 15
Platform entry chain (if equipped) o Platform entry gate (if equipped) o Beacon and alarms (if equipped) o Brake release components o Safety arm o Pothole guards Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
Indicates that tools will be required to perform this procedure. Indicates that new parts will be required to perform this procedure. Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Page 17
5 Check the battery acid level of each battery. If needed, replenish with distilled water to the bottom of the battery fill tube. Do not overfill. 6 Install the vent caps. Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
Emergency Stop button in upper left corner One function select button and Emergency Stop button in upper left corner Controller with Emergency Stop button in lower right corner Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Page 19
8 Activate the up function. Result: The platform should raise. 9 Activate the down function. Result: The platform should lower. The descent alarm should sound while the platform is lowering. Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
Page 20
Be sure the area below the platform is clear of personnel and obstructions before continuing. To continue lowering, release the control handle, wait 5 seconds, then move the control handle again. Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Page 21
Raise the platform the lift function will not operate. approximately 4 feet / 1.2 m from the ground. Proceed to step 38. Result: The pothole guards should deploy. Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
Page 22
40 Press on the pothole guards on one side, and then the other. Result: The drive function should not operate. Result: The pothole guards should not move. Lower the platform to drive. Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
It is the operator's responsibility to read and remember the workplace hazards, then watch for and avoid them while moving, setting up and operating the machine. Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
4 Inspect the workplace. inspection, function tests, and a workplace 5 Only use the machine as it was intended. inspection before using the machine. Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Page 25
2 Pull out the ground and platform red Emergency Stop buttons to the on position. 3 Be sure the battery pack is connected before operating the machine. Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
Page 26
Machine drive speed and function speed will drop when the low battery indicator light is on or when the last light on the battery level indicator is flashing. Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Page 27
4 Chock the wheels. the platform is raised above 26 ft / 7.9 m. Lower the 5 Charge the batteries. platform or retract the platform extension to drive the machine. Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
Page 28
8 Check the battery acid level when the charging cycle is complete. Replenish with distilled water to the bottom of the fill tube. Do not overfill. Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Use chains or straps of ample load capacity. Turn the key switch to the off position and remove the key before transporting. Inspect the entire machine for loose or unsecured items. Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
It should be used only with adequate safety factors. Controls Proportional Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice or obligation. Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Page 35
It should be used only with adequate safety factors. Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice or obligation. Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
Page 36
Ground clearance 2.22 cm It should be used only with adequate safety factors. Pothole guards deployed Weight See Serial Plate (Machine weights vary with option configurations) Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Page 37
Note: Floor loading information is approximate and Weight See Serial Plate does not incorporate different option configurations. (Machine weights vary with option configurations) It should be used only with adequate safety factors. Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246...
Page 38
Ground clearance 2.2 cm It should be used only with adequate safety factors. Pothole guards deployed Weight See Serial Plate (Machine weights vary with option configurations) Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281...
Page 39
Genie North America Phone 425.881.1800 Toll Free USA and Canada 800.536.1800 425.883.3475 Genie Holland Genie Australia Pty Ltd. Phone + Phone + 31 70 51 78836 61 7 3375 1660 Fax + Fax + 31 70 51 13993 61 7 3375 1002...