Table of Contents
Advertisement
1 Antenna Receptacle
2 Dimmer Lead (Orange) (CDM-9807RB/CDE-
9802RB only)
This lead may be connected to the vehicle's
instrument cluster illumination lead. This will enable
the vehicle's dimmer control to dim the backlighting
of the unit.
3 Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio Interface output of a
cellular phone which provides ground shorting when
a call is received.
If a device having the interrupt feature is connected,
audio will be automatically muted whenever the
interrupt signal is received from the device.
4 Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
5 Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle's
fuse box or another unused power source which
provides (+) 12V only when the ignition is turned on
or in the accessory position.
6 Ground Lead (Black)
Connect this lead to a good chassis ground on the
vehicle. Make sure the connection is made to bare
metal and is securely fastened using the sheet metal
screw provided.
7 Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power
antenna, if applicable.
NOTE
This lead should be used only for controlling the
vehicle's power antenna. Do not use this lead to turn on
an amplifier or a signal processor, etc.
8 Fuse Holder
(CDM-9807RB: 20A
CDM-9805R/CDM-9803RM/CDM-9803R/CDE-
9802RB/CDE-9801R: 15A)
9 Battery Lead (Yellow)
Connect this lead to the positive (+) post of the
vehicle's battery.
! ISO Power Supply Connector
" Remote Control Interface Connector
(CDM-9807RB/CDM-9805R/CDM-9803RM/
CDM-9803R only)
To remote control interface box.
For details on how to set the Subwoofer to ON/OFF, see "Subwoofer On and Off" on page 16.
To prevent external noise from entering the audio system.
• Locate the unit and route the leads at least 10 cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car
chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries
various noise suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
# Front Output RCA Connectors (CDM-9807RB/
CDM-9805R/CDM-9803RM/CDM-9803R only)
RED is right and WHITE is left.
# Rear/Subwoofer* Output RCA Connectors
(CDE-9802RB/CDE-9801R only)
RED is right and WHITE is left.
When Subwoofer is set to OFF: Output is from Rear
*
speakers.
When Subwoofer is set to ON: Output is from Subwoofer.
$ Rear Output RCA Connectors
(CDM-9807RB/CDM-9805R only)
RED is right and WHITE is left.
$ Rear/Subwoofer* Output RCA Connectors
(CDM-9803RM/CDM-9803R only)
RED is right and WHITE is left.
*
When Subwoofer is set to OFF: Output is from Rear
speakers.
When Subwoofer is set to ON: Output is from Subwoofer.
% Power Supply Connector
& DIN Connector (CDM-9807RB/CDM-9805R/
CDM-9803RM/CDM-9803R only)
Connect this to the DIN connector on the CD changer.
( Left Rear (+) Speaker Output Lead (Green)
) Left Rear (–) Speaker Output Lead (Green/
Black)
~ Left Front (+) Speaker Output Lead (White)
+ Left Front (–) Speaker Output Lead (White/Black)
, Right Front (–) Speaker Output Lead (Grey/
Black)
- Right Front (+) Speaker Output Lead (Grey)
. Right Rear (–) Speaker Output Lead (Violet/
Black)
/ Right Rear (+) Speaker Output Lead (Violet)
: ISO Connector (Speaker Output)
; DIN Extension Cable (Included with CD changer)
NOTE
Older Alpine CD changer came with standard, straight
type DIN connectors. In installations where an L-type
connector would simplify installation, the Alpine 4910
Adaptor can be used (sold separately).
< Subwoofer Output RCA Connectors
(CDM-9807RB/CDM-9805R only)
RED is right and WHITE is left.
= RCA Extension Cable (sold separately)
02
23
-EN
Advertisement
Table of Contents
