Table of Contents
Advertisement
Operating and Assembly Instructions
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and
others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for
future reference.
Airless
Paint Sprayers
For questions, parts and accessories: 1-800-626-4401
Models PS250B and PS250E
Models PS240C and PS240F
Models PS231B, PS260E, PS261C,
and PS260F
IN424700AV 12/08
© 2008 Campbell Hausfeld/Scott Fetzer
For parts, product & service information
visit www.chpower.com
Advertisement
Table of Contents
Related Manuals for Campbell Hausfeld PS240C
Summary of Contents for Campbell Hausfeld PS240C
- Page 1 Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. Airless Paint Sprayers For questions, parts and accessories: 1-800-626-4401 Models PS250B and PS250E Models PS240C and PS240F Models PS231B, PS260E, PS261C, and PS260F IN424700AV 12/08 © 2008 Campbell Hausfeld/Scott Fetzer For parts, product & service information...
-
Page 2: Table Of Contents
Operating Instructions and Assembly Instructions Airless Paint Sprayers Table of Contents Description ........2 Application Chart . -
Page 3: Safety Guidelines
Operating Instructions and Assembly Instructions Airless Paint Sprayers Safety Guidelines ImPOrTANT SAFETy INSTrUCTIONS SAvE ThESE INSTrUCTIONS This manual contains information that is very important to know and understand. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this information, observe the following symbols. - Page 4 ● Never try to stop leaks with any part of your body. ● This system is capable of producing 3000 psi (20 500 kPa). Use only Campbell Hausfeld replacement parts rated at 3000 psi (20 500 kPa) or higher. To reduce the risk of skin injection: ●...
- Page 5 ● Use only conductive or grounded high-pressure airless paint sprayer hoses specified by the manufacturer. ● Verify that all containers and collection systems are grounded to prevent static discharge.
-
Page 6: Assembly Instructions
Operating Instructions and Assembly Instructions Airless Paint Sprayers Assembly Instructions TOOlS rEqUIrED: 3/4 in. or Adjustable Wrench 5/8 in. or Adjustable Wrench ASSEmbly 1. Open packaging and check contents. 2. Remove the equipment and all parts from the carton. 3. If sprayer is on stand, no further frame assembly is necessary. - Page 7 Operating Instructions and Assembly Instructions Airless Paint Sprayers Preparation (Continued) DO NOT ATTACh ThE SUCTION ASSEmbly UNTIl INSTrUCTED TO DO SO IN STEP . 1. Remove inlet valve cap and with your smallest finger, push on inlet valve stem to ensure it moves freely. 2.
-
Page 8: Spraying Instructions
Operating Instructions and Assembly Instructions Airless Paint Sprayers Preparation (Continued) 10. After completing the flush/testing process, purge the pump of fluid. 11. Repeat the preceding steps using paint instead of cleaning solvent. NOTE: Strain and thin paint before using. All paint may have particles that will clog filter and spray tips. - Page 9 Operating Instructions and Assembly Instructions Airless Paint Sprayers Spraying Instructions (Continued) INTErmITTENT USE If you are spraying and decide to stop for several minutes, lock the spray gun trigger and submerge the tip in a container of water (See Figure on page 8).
-
Page 10: Cleanup
NOTE: Cleaning and maintenance of the pump are the most important steps you can take to ensure proper operation and a long life for your airless paint sprayer. Please follow the cleaning instructions carefully and . . . wEAr All NECESSAry SAFETy GEAr NECESSAry TOOlS / mATErIAlS: •... - Page 11 Operating Instructions and Assembly Instructions Airless Paint Sprayers ClEANUP FOr ChANGING PAINTS Or TEmPOrAry STOrAGE FOr mOrE ThAN ONE NIGhT wEAr All NECESSAry SAFETy GEAr NECESSAry TOOlS / mATErIAlS: • Pliers • Rag • Gloves • Two (2) buckets • At least one (1) gallon of cleaning fluid •...
- Page 12 Operating Instructions and Assembly Instructions Airless Paint Sprayers ClEANUP FOr ChANGING PAINTS Or TEmPOrAry STOrAGE FOr mOrE ThAN ONE NIGhT (Continued) Allow the to continue cleaning fluid circulating for approximately 10 minutes. 7. Turn pressure to HIGH (completely clockwise). 8. Turn prime/spray control to SPRAY/ ROLL position.
- Page 13 Operating Instructions and Assembly Instructions Airless Paint Sprayers ClEANUP FOr ChANGING PAINTS Or TEmPOrAry STOrAGE FOr mOrE ThAN ONE NIGhT (Continued) 17. Make sure prime/spray control is in SPRAY position to reduce dribbling. 18. Turn pressure to LOW (completely counterclockwise). 19.
-
Page 14: Storage
Operating Instructions and Assembly Instructions Airless Paint Sprayers Storage ShOrT TErm (lESS ThAN ONE wEEk) wEAr All NECESSAry SAFETy GEAr NECESSAry TOOlS / mATErIAlS: • Pump Protector Solution • Plastic Wrap • 3/4 in. or Adjustable Wrench OIL OR ALKYD BASED PAINT If sprayer cleaned with mineral spirits, simply wrap suction filter housing in plastic to keep debris out of... -
Page 15: Spray Gun Maintenance
Operating Instructions and Assembly Instructions Airless Paint Sprayers Spray Gun maintenance pump damage may occur if these instructions are not followed. Before performing any maintenance, make sure to relieve pressure from system and disconnect power from sprayer. • Do not use oil based solvents to clean equipment after using latex based coatings. Use only warm soapy water. • Always replace clogged gun filters, do not attempt to clean them. -
Page 16: Maintenance Chart
Operating Instructions and Assembly Instructions Airless Paint Sprayers maintenance Item Check Before each use Product safety labels Trigger adjustment Before each use Before each use Airless hose Before each use Sealing surfaces Suction tube Before each use Before each use Bypass tube Before each use Suction filter... -
Page 17: Specifications
Operating Instructions and Assembly Instructions Airless Paint Sprayers Specifications Operating Pressure model A - D Power ratings 0-3000 psi 115 Volts AC 60 Hz 8.5 Amps weight model (lbs.) @ 0 psi PS2###B/E 49 * PS2###C/F 55 * PS2###D 55 * * Weight does not include mounting model motor kit... -
Page 18: Replacement Parts
Faceplate screws Cast faceplate Faceplate gasket Pressure valve assembly Housing kit (Includes 20,29, & 30) www.chpower.com Address parts correspondence to: Campbell Hausfeld Attn: Customer Service 100 Production Drive Harrison, OH 45030 U.S.A. 13 12 Part ref. qty. Description... -
Page 19: Replacement Parts List
Actuator, Gun Nut, #5-40 Hex Lock Kit, Gun Trigger (Trigger, Screws) AL183100SV Gun Filters, 100 Mesh (yellow) 50 Mesh (white) Address parts correspondence to: Campbell Hausfeld Attn: Customer Service 100 Production Drive Harrison, OH 45030 U.S.A. (4x) Part ref. qty. - Page 20 Knob Washer Spacer Palnut Wheel Cart By-pass Tube & Clamp Option, Solvent Resistant www.chpower.com Address parts correspondence to: Campbell Hausfeld Attn: Customer Service 100 Production Drive Harrison, OH 45030 U.S.A. Part ref. qty. AL167960AD 1 MJ103305AV 2 PM080900AV 2 ST090200AV...
-
Page 21: Troubleshooting
Operating Instructions and Assembly Instructions Troubleshooting Chart Symptom Possible Cause(s) Motor hums and does not run 1. Unit under pressure 2. Equipment has been dropped which caused motor to become misaligned 3. Supply voltage too low Motor does not run or hum 4. - Page 22 Operating Instructions and Assembly Instructions Troubleshooting Chart (Continued) Symptom Possible Cause(s) Pump primes and builds 21. Clogged gun filter pressure, however, the equipment does not spray or 22 Clogged Spray Tip produce a quality spray pattern 23 A. Tip is damaged or worn B.
-
Page 23: "Force Feeding" Pump
Operating Instructions and Assembly Instructions Airless Paint Sprayers “Force Feeding” Pump To remove trash that has been caught in the valves, the unit can be force fed. With pump on and prime/spray knob turned to “prime” position, pour the appropriate solvent into the suction tube and then fold hose as shown opposite. -
Page 24: Warranty
ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE , OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.