Advertisement
Safety Instructions (continued)
8. Follow all local electrical and safety
codes, as well as the National
Electrical Code (NEC) and the
Occupational Safety and Health Act
(OSHA).
9. Wiring and fuses should follow electri-
cal codes, current capacity, and be
properly grounded.
10. Electric motors must be securely and
adequately grounded. See grounding
instructions and extension cord infor-
mation in this manual.
11. Always disconnect power source
before working on or near a motor, or
its connected load. If power discon-
nect point is out-of-sight, lock it in the
open position and tag to prevent
unexpected application of power.
12. Guard all moving parts; keep visitors
away. Never allow children in work
area.
13. Use only a properly grounded outlet
that will accept a three pronged plug,
and wear shoes to prevent shock
hazards.
14. Be careful when touching exterior of
operating motor; it may be hot
enough to cause injury.
15. Protect power cable from coming in
contact with sharp objects.
16. Clean electrical or electronic equip-
ment with an approved cleaning
agent, such as dry, nonflammable
cleaning solvent.
17. To avoid spontaneous combustion,
discard waste rags into approved
metal waste cans.
18. Never store flammable liquids or
gases in vicinity of compressor.
19. When spraying with solvent of toxic
chemicals, follow instructions provid-
ed by the chemical manufacturer.
20. Spray in a well ventilated area, to
keep fumes from collecting and caus-
ing health and fire hazards.
21. Do not spray in vicinity of open
flames or other places where a spark
can cause ignition. Do not smoke
when spraying paint, insecticides, or
other flammable substances.
22. Use a respirator when spraying.
23. NEVER reset safety valve or pres-
sure switch. Keep safety valve free
from paint and other accumulations.
This provides safety against over
pressure.
24. Do regular maintenance; keep all
nuts, bolts, and screws tight, to be
sure equipment is in safe working
condition .
25. Keep cleaning rags and other flam-
mable waste materials in a tightly
closed metal container and dispose of
later in the proper fashion.
26. Drain tanks of moisture after each
day's use. If unit will not be used for a
while, it is best to leave drain cock
open until such time as it is to be
used. This will allow moisture to com-
pletely drain out and help prevent
corrosion of inside of tank.
27. Inspect tank yearly for rust, pin holes
or any other imperfections that could
cause it to become unsafe. NEVER
weld or drill holes in air tank.
4
Pièces de rechange
Pour les pièces de rechange, appeler le 1-800-4-RIDGID
S'il vous plaît fournir l'information suivante:
-Numéro du modèle
-Numéro de série (si applicable)
-Description de la pièce et son numéro sur la liste de pièces
No.
No de
Numéro
Ref.
catalogue
de pièce
1
25673
WL373001AV
* Montage pompe/moteur
2
20448
ST085700AV
3
17713
ST158000AV
4
17718
WL003202AV
5
17723
WL003203AV
6
17728
CV223800AV
* Clapet
L
7
25678
L
8
—
L
9
—
10
—
ST188800AV
11
17753
ST209800AV
12
17758
CW209600AV
13
17763
EC012600AV
14
17773
GA016709AV
* Jauge du réservoir
N/D
15
—
16
17793
WL024501AV
* Ensemble rég. (inclut jauge du réservoir, raccord et
17
17798
V-215106AV
18
17808
ST185600AV
* Prise
19
17813
WL025900AV
20
17838
WL025800AV
21
17848
ST073276AV
22
17853
ST158300AV
G
23
25003
24
17863
ST074415AV
G
25
24998
26
17873
HF203300AV
* Raccord
* Jauge de sortie
27
17878
GA016705AV
28
17883
CW210001AV
* Soupape de déchargement
29
17888
ST022500AV
30
17898
HF002401AV
31
36208
CW217800AV
* Couvercle de manostat
32
17908
CW211300AV
* Manostat (inclut soupape de déchargement et
33
17913
D-1403
* Robinet de vidange du réservoir
34
17918
ST073612AV
35
17923
AR052700OE
36
17928
ST129301AV
37
17933
ST129302AV
38
17938
WL012406AV
39
17943
ST188900AV
L
WL029600AV
G
ST170400AV
Pièces considérées comme sujettes à l'usure normale
*
N/D = articles de quincaillerie standard
Description
Filtre
Embase de bouton
Douille en caouct chouc (Arrière)
Douille en caouct chouc [avant]
Tuyau d'echappement (écrous et viroles inclus)
Écrou
Virole
Tuyau de déchargement
(insert de tuyau, écrou et virole inclus)
Vis de décharge de tension
Décharge de tension
Cordon
Vis de 1/4 po - 20 x 1/2 po
jauge de sortie)
Soupape de sûreté 1138 kPa
Arceau de sécurité
Fixation de panneau de contrôle
Vis de pied
Pare chocs en caoutchouc mouté
Tuyau de panneau de commande (inserts de tuyau inclus)
Vis autotaraudeuse de 1/4 po - 20 x 1/2 po
Raccord de compression à coude (inclut raccord et
virole inclus)
Bouchon
Raccord
couvercle de manostat)
Bouchon
Double réservoir 15,14 L
Vis de couvercle de protection
Vis de couvercle de protection
Couvercle
Raccord d'échappement
Trousse de tuyaux d'échappement (sans soupape de clapet)
Trousse de tuyau de panneau de commande
(inserts, écrous et viroles inclus)
Fr 21
Qte
1
1
3
1
2
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
4
4
1
4
2
2
1
1
1
1
1
1
1
1
1
1
2
1
1
Advertisement
Chapters
