Tail Support / 尾管支撐架組裝 - THUNDER TIGER mini Titan V2 Series Instruction Manual

TAIL SUPPORT / 尾管支撐架組裝
Bag P
No. Material No. Description
1 BK1026 BRACKET
2 BK1027 ROD ø3×255mm
3 BK1025 TAIL SUPPORT ROD END
4 BK1889 FRAME SPACER
5 HMC2-10B SOCKET SCREW M2×10
6 HMC2-14B SOCKET SCREW M2×14
Secure all screws shown on this page with a drop of thredlocker.
本頁顯示之螺絲請使用適量防鬆膠鎖固。
Step 1 / 步驟一
HMC2-10B
SOCKET SCREW M2×10
1. Apply CA or Epoxy when assembling the Tail Support Rod End.
M2×10
內六角螺絲
2. Install the Tail Support Bracket and fit the Tail Support Rod.
1. 使用快乾膠接合尾支撐桿接頭與碳纖棒。
2. 將支撐桿座與支撐桿接合。
HMC2-14B
SOCKET SCREW M2×14
M2×14
內六角螺絲
HML2
M2 NUT
M2
螺帽
BK0922
BALL LINK D3.8x12mm
D3.8x12mm
單頭連接桿
HSP16-6N
COUNTERSUNK SCREW M1.6×6
Step 2 / 步驟二
M1.6×6
圓頭十字螺絲
1. Remove the tail servo wheel prior to attaching the Linkage Ball.
2. For the rudder servo, mount the Linkage Ball at 10.5mm from
BK1203
3. Secure the servo to the Tail Servo Tray and attach the
LINKAGE BALL (ø3.8)
(ø3.8)
連接頭
1. 從尾舵伺服機上將伺服機擺臂拆下，安裝連桿頭。
2. 將連桿頭安裝於距離擺臂中心位置10.5mm處作為初始設定，
3. 將伺服機安裝於尾舵伺服機固定座，並與連桿連接。
HNN2-10B
TAPPING SCREW(W/WASHER) M2×10
圓頭墊圈自攻螺絲 M2×10
All manuals and user guides at all-guides.com
Qty
名稱
1
尾支撐桿座
ø3×255mm 2
碳纖棒
4
尾支撐桿接頭
1
機身支柱
M2×10 2
內六角螺絲
M2×14 1
內六角螺絲
(3)
(5)
CA
CA or Epoxy
瞬間膠或環氧樹脂
Apply C.A Glue
使用快乾膠黏合
the center of the servo arm as beginning. Please refer to the
manual of your gyro to choose the length of the arm.
rod to the servo arm.
建議您參考陀螺儀說明書安裝。
(12)
(12)
(11)
(10)
No. Material No. Description
7 HML2 M2 NUT
8 BK1071 TAIL LINKAGE ROD ø1.3
9 BK0922 BALL LINK D3.8x12mm
10 HSP16-6N COUNTERSUNK SCREW M1.6×6
11 BK1203 LINKAGE BALL (ø3.8)
12 HNN2-10B TAPPING SCREW(W/WASHER) M2×10
(4)
(2)
(2)
(3)
(7)
Apply threadlocker
使用螺絲防鬆膠
(9)
-19-
Qty
名稱
M2
螺帽
ø1.3
尾拉桿
D3.8x12mm
單頭連接桿
M1.6×6
圓頭十字螺絲
(ø3.8)
連接頭
M2×10
圓頭墊圈自攻螺絲
(6)
T22
(1)
(9)
(8)
1
1
2
1
1
2