Related Manuals for Gree GPC08AL-A3NNA2B
Summary of Contents for Gree GPC08AL-A3NNA2B
- Page 1 MODEL : GPC08AL-A3NNA2B www.gree.ca Saint-Mathieu-de-Beloeil (Quebec) Canada Made in China 042021 © Copyright, GREE Canada, 2021...
- Page 2 model no 043-6138-6 / 043-5443-4 contact us: 1.866.523.5218 sAFETy WARNiNG ..................1 PART's NAmE ....................2 CLEAN ANd mAiNTENANCE ..............3 mALFuNCTioN ANALysis ................5 iNsTALLATioN PRECAuTioN ..............8 PREPARATioN BEFoRE iNsTALLATioN ..........9 iNsTALLiNG WiRE THE HooK ..............10 REmoviNG CoLLECTEd WATER ..............11 iNsTALLATioN iN A douBLE-HuNG sAsH WiNdoW ......14 iNsTALLATioN iN A sLidiNG sAsH WiNdoW ..........18 iNsTALLATioN ANd disAssEmBLy oF HEAT disCHARGE PiPE ..22 oPERATioN iNTRoduCTioN FoR CoNTRoL PANEL ......25...
- Page 3 � DANGER Indicates a hazardous situation that, if not avoided, will result in death or serious injury. � WARNING Indicates a hazardous situation that, if not avoided, could result in death or serious injury. � CAUTION Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury.
- Page 4 contact us: 1.866.680.4733 • This appliance can be used by children aged from 8 years and above and people with reduced physical ,sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
-
Page 6: Clean Filter
contact us: � .866.680.4733 WARNING • Before cleaning the air conditioner, please turn off the unit and disconnect power. Otherwise, it may cause electric shock. • Do not wash air conditioner with water. Otherwise, it may cause electric shock. • Do not use volatile liquid (such as thinner or gas) to clean the air conditioner. Otherwise, it may damage the appearance of air conditioner. -
Page 7: Checking Before Use-Season
Clean heat discharge pipe Remove the heat discharge pipe from air conditioner, clean and dry it , and then reinstall it. (For the method of installation and removal , please refer to the instruction for "installation and disassembly of heat discharge pipe"). Checking before use-season 1. - Page 8 contact us: 1.866.680.4733 Please check below items before asking for maintenance. if the malfunction still can't be eliminated, please contact local dealer or qualified professionals. Solution Troubleshooting Phenomenon • Power failure? • Wait after power recovery. • is plug loose? •...
- Page 9 Solution Troubleshooting Phenomenon • Whether air outlet or air • Eliminate the obstacles. inlet is blocked? • under heating mode, • mobile unit will stop blo whether indoor temperatu- wing fan after reaching No fan blowed re ireaches set set temperature. out from air temperature? conditioner...
-
Page 10: Malfunction Code
contact us: 1.866.680.4733 Malfunction code 1. Pour out the water inside chassis. 2. if "H8" still exits, please contact Chassis is full of water. professional person to maintain the unit. malfunction of ambient Please contact professional temperature sensor. person to deal with it. malfunction of evaporator Please contact professional temperature sensor. -
Page 11: Selection Of Installation Location
WARNING • observe all governing codes and ordinances. • do not use damaged or non-standard power cord. • Be caution during installation and maintenance. Prohibit incorrect operation to prevent electric shock, casualty and other accidents. Selection of installation location basic requirement installing the unit in the following places may cause malfunction. - Page 12 heat discharge joint A pipe joint B joint C wire hook (2) pipe clip screw(8) drainage pipe rubber plug pipe hoop (2) Window panel Exhaust cover Extension panel Adjustment panel foam seal A (2) Insect guard net Rain guard (2) Bracket Window kit battery (2)
- Page 13 • Assemble the wire hook at the back of the unit with screws (the direction of wire hook is as shown in following fig). direction of wire hook is upward Wire hook screw direction of wire hook is downward • Wind the power cord around the wire hook.
- Page 14 contact us: 1.866.680.4733 There are 2 ways to remove collected water: use the continuous drainage option from the bottom hole. Note: When using the continuous drainage option from the bottom hole, install drainage pipe before using, otherwise poor drainage will affect normal operation of the unit.
- Page 15 Drainage way as follows. 1. in cooling or drying operation, the condensation water will be drained to the chassis and spattered by water-striking motor. As the temperature of condenser is high, most of the condensation water will be evaporated and drained to outdoor.
- Page 16 contact us: 1.866.680.4733 use the continuous drainage option from the middle hole. Note: Water can be automatically emptied into a floor drain by attaching 14mm inner diameter hose (not included). 1. Remove the continuous drain cap 1 by turning it counter clockwise then remove the rubber stopper 2 from the spout.
- Page 17 Note: if the inner width of window is below 20.5" 520mm, please remove the adjusting panel from window frame and then cut the window frame to make its width the same as the width of window. Adjusting panel Window frame 1.
- Page 18 contact us: 1.866.680.4733 spring washer support Washer Bolt 5. Fix the rain shield on the support with 2 nuts, spring washer, washer and bolt. screws screws spring washer Note: protective grille, support, rain shield, nut, bolt, spring washer and washer are optional accessories;...
- Page 19 38.5 980 38.5 38.5 980 59 1500 38.5...
-
Page 20: Installation In A Sliding Sash Window
contact us: 1.866.680.4733 9. Close the window sash securely against the Window panel. 10. Cut the sponge A to a proper length and seal the gap between upper part of inner window sash and outer window sash. 11. Fix the inner window with window bracket and screw, so that it can not slide vertically.dow sash securely against the Window panel. - Page 21 Window frame Joint B+C 3. Fix the protective grille on joint B+C with 2 screws. screws Protective grille 4. Fix the support on the outer side of window frame with 2 nuts, spring washer, washer and bolt. Washer spring washer Bolt 5.
- Page 22 38.5 980 38.5...
- Page 23 38.5 1500 38.5...
- Page 24 contact us: 1.866.680.4733 10. Cut the sponge A to a proper length and seal the gap between left side of inner window sash and outer window sash. 11. Fix the inner window with window bracket and screw, so that it can not slide horizontally.
- Page 25 Install heat discharge pipe 1. Rotate joint A clockwise into the heat discharge pipe. Heat discharge pipe Join A Clockwise 2. install another side of heat discharge pipe clockwise into protective grille sub-assy. Heat discharge pipe Join A 3. insert joint A of heat Clasp discharge pipe (the The side with "ToP"...
- Page 26 contact us: 1.866.680.4733 Note on Installing heat discharge pipe) in order to improve cooling efficiency, the heat discharge pipe should be as short as possible and flat without curve to ensure smooth heat discharge. correct correct correct wrong • The length of the heat discharge pipe is less than 1m. it is recommended to use it with shortest length.
- Page 27 • Correct installation is shown in figure below (when installing it through a wall, height of air outlet should be about 40-130cm above floor). • Wrong installation is shown in following figure (if the pipe is bent too much, it would easily cause malfunction.) Disassemble heat discharge pipe 1.
- Page 28 indicator Heat...
- Page 29 MODE button Press this button and the mode will circulate according to below sequence: CooL COOL: under this mode, the cooling mode indicator lights up. The screen dis- plays set temperature. Temperature setting range is 61°F (16°C) - 86°F (30°C). DRy: under this mode, drying mode indicator lights up;...
- Page 30 Timer Timer...
- Page 31 .----- + BUTTON Press this button to increase the temperature setting. Hold the button down for two seconds to change the numbers quickly. When the button is released, the �� ° F) symbol will be displayed. 1:..1 � Temperature adjustment is unavalaible in the Auto mode, UL.J LJ!_J...
- Page 32 Bouton SWING left and right...
- Page 33 User Guide-General use 1. After turned on, press the <!.l button, to run the unit. (Note: When it is powered on, the guide louver of main unit will close automatically.) G)--1.J!U �------® 2. Press the MODE button to select the desired running L Jb..J mode.
- Page 34 contact us: 1.866.680.4733 • About Lock Press the + and - buttons simultaneously to lock or unlock the keyboard. If the remote control is locked, the icon will be displayed. When any button is pressed, the icon will flash three times. When the keyboard is unlocked, the icon will disappear. •...
- Page 35 (1) yEAR from the date of original purchase in Canada. during the warranty period, if this Air Conditioner fails under normal use, GREE will, at its option, either repair the unit or replace it, free of charge, within a reasonable period of time after the Air Conditioner is returned.