Related Manuals for Gree GPC08AI-K3NNC6A
Summary of Contents for Gree GPC08AI-K3NNC6A
-
Page 1: Service Manual
Change for Life Service Manual GREE ELECTRIC APPLIANCES,INC.OF ZHUHAI... - Page 3 Cool Heat MODE High Auto ON/OFF Fan only T-ON T-OFF AUTO SWING COOL SLEEP LOCK SPEED HEAT ON/OFF MODE SWING SLEEP TIMER...
- Page 7 Front Cool Heat MODE High Auto ON/OFF Fan only Rear...
- Page 8 Cool MODE SPEED Heat Auto High ON/OFF Fan only Cool Heat MODE SPEED High Auto ON/OFF Fan only...
- Page 9 HEAT HEAT EXCHANGE EXCHANGE (CONDENSER) (EVAPORATOR) COMPRESSOR Capillary Strainer...
- Page 10 POWER BN(BK) TUBE TEMP. ROOM TEMP. WATER MOTOR SENSOR SENSOR BU(WH) YEGN YEGN(GN) TUBE ROOM L(3) WATER1 COMP. C(T,U) K201 DISP2 MOTOR YEGN DISP2 COMP COMP(4) R(M,V) S(W,X) DISP1 ELECTRIC BOX DISP1 HIGH-WP YEGN WATER LEVEL SWITCH UP FAN MOTOR...
- Page 11 POWER BN(BK) TUBE TEMP. ROOM TEMP. WATER MOTOR SENSOR SENSOR BU(WH) YEGN YEGN(GN) TUBE ROOM L(3) WATER(WATER1) COMP. C(T,U) K201 DISP2 MOTOR YEGN DISP2 COMP COMP(4) R(M,V) S(W,X) DISP1 ELECTRIC BOX DISP1 HIGH-WP YEBK WH YEGN WATER LEVEL SWITCH UP FAN MOTOR Wire connection among display panel...
- Page 12 Indoor fan Fuse Copper fin N3 of neutral wire Piezoresistor Copper fin N1 of neutral wire Rectifier Buzzer Interface of display board High water-level inspection interface Ambient temperature sensor Tube temperature sensor...
- Page 13 ON/OFF Press it to start or stop operation. MODE Press it to select operation mode(AUTO/COOL/DRY/FAN/HEAT). : Press it to increase temperature setting. : Press it to decrease temperature setting. Press it to set fan speed. SWING Press it set swing angle. SLEEP TIMER Press it set auto-on/auto-off timer.
-
Page 14: Replacement Of Batteries
SWING Press this button to activate or deactivate the swing. SLEEP: Press this button, Sleep On and Sleep Off can be selected. After powered on,Sleep Off is defaulted. After the unit is turned off, the Sleep function is canceled. After Sleep function set up, the signal of Sleep will display. In this mode, the time of timer can be adjusted. - Page 15 Panel LED window Temperature selection button COOL mode lamp Receiver window DRY mode lamp Cool Mode speed Auto High ON/OFF Fan only FAN Speed lamp Fan speed button ON/OFF button MODE button FAN mode lamp the button the buzzer will give out .
-
Page 16: Set Speed
The temperature in this manual is expressed by Centigrade. If Fahrenheit is used, the switchover between them is Tf=TcX1.8+32 1. Temperature Parameters ■Indoor preset temperature (Tpreset) ■Indoor ambient temperature (Tamb.) 2. Basic functions 2.1 Cool Mode Once the compressor is energized, there should be a minimum interval of 3 minutes between two start-ups. Once the compressor operates, the unit will not stop within 6 minutes due to temperature change. - Page 17 Tpreset<Tamb.<Tpreset + 4°F(2°C) Medium speed; Tamb.≤Tpreset Low speed; (b) There is 210s’ delay for switch of Auto Fan mode. 3.4 Timer Function General Timer Timer ON can be set at unit OFF. If selected ON time is reached, the unit will start to operate according to previous setting status. Time setting range is 0.5-24hr in 30-minute increments.
- Page 18 Install Exhaust Hose and Adapter 1. Roll air conditioner to its selected location. See Location Requirements. 2. Insert one end of the flexible exhaust hose into the exhaust adapter. 3. Twist clockwise to lock hose into place. 4. Insert the other end of the flexible exhaust hose into the window exhaust adapter. 5.
- Page 19 If the pipe are to be bent, please install it by considering following dimension. 55cm 55cm Wrong installation is shown in following figure (If the pipe is bent too much, it would easily cause malfunction.)
- Page 26 Energize and turn on the unit Check the connection Indoor unit status of indoor display F1-F2 ? temperature sensor Indoor unit whether it's displays F3/F4/ connected tightly? Check the connection status Adjust the of outdoor connection status temperature sensor Replace Whether it's Is malfunction temperatur...
- Page 27 Turn on the unit Display Refer to the indication of If the defrosting instruction to tray is over-blow discharge the water of chassis. Connection line of water Failure is cancelled . level switch is tight. Adjustcon nection Replace thes Failure is Failure is witch of water cancelled.
- Page 28 Turn on the unit Motor does not rotate If the Replace connection control line is board tight. Adjustcon nection Failure is cancelled. Replace Failure is cancelled control board Failure is Replace cancelled. motor...
- Page 29 Start Normal fluctuation is within 10% of the rated voltage on the Is the supply voltage unstable with big fluctuation? Malfunction is eliminated. nameplate Is the supply voltage too low with overload? Adjust the supply voltage to maintain it within normal range Malfunction is eliminated.
- Page 30 mode occures...
- Page 31 Steps Procedure 1.Remove front panel Remove 2 retaining screws on front panel and then lift the front panel up to remove it. front panel screws 2.Remove wire-passing plate wire-passing plate Remove retaining screws on wire-passing plate. Then remove the plate. screw...
- Page 32 Steps Procedure 4.Remove rear plate Remove 6 retaining screws on rear plate. screws Then remove rear plate. rear plate front case 5.Remove front case screws screws Remove retaining screws on front case. Then remove front case. 6.Remove display panel display panel screws Remove retaining screws on display panel.
- Page 33 Procedure Steps 8.Remove cover of propeller housing cover of propeller housing Remove screws on cover of propeller housing. Then remove the cover. screws 9.Remove support plate 1 support plate 1 Remove screws on support plate and then remove support plate 1. screws 10.Remove connecting pipe Unsolder each welding point of connecting...
- Page 34 Steps Procedure 12.Remove air duct air duct Remove 4 retaining screws on air duct. Then remove air duct. screws 13.Remove propeller housing (upper) screws propeller housing Remove 4 screws of propeller housing (upper) (upper). Then remove propeller housing (upper). 14.Remove centrifugal fan blade (upper) centrifugal fan blade Remove nuts and washer of centrifugal fan (upper)
- Page 35 Procedure Steps 18.Remove motor water tray Remove water tray, and then remove 3 motor screws support plates 2, 3 19.Remove splash plate and support plates 2, 3 splash plate Remove screws of splash plate and then remove splash plate. Remove screws on support plates 2,3.
- Page 36 Add: West Jinji Rd, Qianshan, Zhuhai, Guangdong, China, 519070 Tel: (+86-756) 8522218 Fax: (+86-756) 8669426 E-mail: gree@gree.com.cn www.gree.com For continuous improvement in the products, Gree reserves the right to modidy the product specification and appearance in this manual without notice and without incurring any obligations.