Presetting Service; Tuning To Preset Service; Service Component/Pty Search Function; Service Search Function - Alpine OWNER'S MANUAL Owner's Manual

4
Touch [ ] / [ ], [ ] / [
the Service or Ensemble up or down respectively.
Touch and hold to change the Service or Ensemble continuously.
• The , buttons provide the same functions above.

Presetting Service

1
Select the band and ensemble, and then tune in a
desired service you wish to store in the preset memory.
2
Touch the preset number you want to store, for at least 2
seconds.
The selected station is stored.
The display shows the service label or channel number
memorised.
3
Repeat the procedure to store up to 17 other stations
onto the same band.
To use this procedure for other bands, simply select the desired
band and repeat the procedure.
• A total of 18 services can be stored in the preset memory.
• If you store a service in a preset memory which already has a service,
the current service will be cleared and replaced with the new service.
• For details on switching to the Preset mode screen, see
main screen example" (page 51).

Tuning to Preset Service

You can tune in the preset stations in memory on either band using its
preset number.
Touch any one of the preset buttons that has a service stored
to it.
The preset service is received.
• For details on switching to the Preset mode screen, see
main screen example" (page 51).

Service Component/PTY Search Function

You can select your favourite Service Component from the All Service
list, Current Ensemble Service list or PTY Search list.

Service Search Function

1
Touch [ ] (Search).
2
Touch [ ] (All) or [
The All Service list or Current Ensemble list in the Full Search
mode screen is displayed.
ALL: All the currently available Service Component (Primary/
Secondary) lists are displayed.
Current Selectable Service Component (Primary/Secondary) lists
Ensemble: from the Ensemble currently being received are
displayed.
3
Touch the desired Service component.
The Selected service component is received.
• A Secondary Service list that was derived from the Primary Services is
displayed in the Service Component list.
• The TP indicator is displayed in the Service Component (Primary) list
currently being received.
52
] or [ ] / [ ] to change
in "DAB
in "DAB
] (Current Ensemble).
• The PTY is displayed in the Service Component (Primary) list currently
being received.
• You can also narrow down the options and search the Service name
using the alphabet search function. (Primary Component only) For
details, see "Alphabet Search Function" (page 59).

PTY Search Function

1
Touch [ ] (PTY Search).
A programme type list that was derived from the Primary
Services currently being received as Service components is
displayed.
• When the All Service list or Current Ensemble list screen is being
displayed, touch [ ] (PTY).
2
Touch the desired programme type.
The Service Component list that corresponds with the selected
programme type is displayed.
3
Touch the desired Service Component.
The selected Service Component is received.
List Update Function
You can update each list while it is being displayed.
Touch [ ] (List Update).
The list is updated to the currently available list.

Interruption Function

If Interruption Function is enabled, when the following broadcast is
received, the unit switches to the DAB source screen automatically, and
will receive broadcasts.
- Alarm (Emergency Broadcast)*
- TA(Traffic Announcement)*
2, 3
- Announcement*
2
- News Announcement*
*1 Set Alarm to "On" in "Setting Alarm (Emergency Broadcast)
Reception" (page 39).
*2 Not interrupted during the RDS broadcast reception.
*3 Select the Announcement type received in "Setting Announcement
Reception" (page 39), then set the Announcement setting to "On. "
*4 The Interruption Function for Traffic Announcements works with RDS
broadcasts. Therefore, even if the current source is DAB, a Traffic
Announcement by RDS broadcast may interrupt.
• "DAB Alarm"/"DAB T.Info"/"DAB News" is displayed respectively on
the Source title section during each broadcast reception.
The display differs during announcement reception depending on the
announcement type set in "Setting Announcement Reception"
(page 39).
• To cancel the Interruption function, touch the DAB main screen or press
any of the following buttons.
(MENU)/ / /
• When the interruption broadcast is over, the unit returns to the
previous screen.
• Does not interrupted during Hands-free phone talk. During camera
image display, only the sound may be interrupted.
• The volume level will be memorised if the volume is adjusted during
interruption broadcast reception. When an interruption broadcast is
received the next time, the volume level is automatically adjusted to the
memorised level.
1, 2
4
(NAVI)