Table of Contents
Advertisement
Quick Links
Operation and Maintenance Manual
T
C
ABLE OF
ONTENTS
Warranty Information .......................... 2
Your Documentation Package ............... 3
Safety Information .............................. 4
Safety Features ................................... 4
Important Installation Instructions .......... 4
Pre-Installation Checklist ......................... 5
Adjustments ........................................ 9-10
Programming theRemote Control ....... 11
Installation of Light Bulb ....................... 19
Troubleshooting Guide .................. 20-21
Parts List and Explosion ...................... 22
Accessories .............................................. 23
For Help, call 1-800-35-GENIE
2 M 4 M
AC Powered Belt Drive
C
OMPLETE WITH
R
C
EMOTE
ONTROL AND
E
LECTRONICS
For up to 7' 6" tall Doors.
IncludedWall Control MUST be installed prior to
Operation of thisGarage Door Operator.
Safe-T-Beam ® Safety Reverse System Must be Installed
and the Force Controls MUST be Properly Set to
close door.
ThisEquipment meets or exceeds all Federal,State and
UL325 Safety Requirements.
Having Difficulty?Need Help?
Please call us: 1-800-35-GENIE (354-3643)
Please have Model information ready whencalling
3563435770
®
I
NTELLICODE
SER IES II
.
Advertisement
Table of Contents
Related Manuals for Genie Quietlift 2M
Summary of Contents for Genie Quietlift 2M
-
Page 1: Table Of Contents
Installation of Light Bulb ....... 19 UL325 Safety Requirements. Troubleshooting Guide ....20-21 Parts List and Explosion ...... 22 Having Difficulty?Need Help? Accessories ..........23 Please call us: 1-800-35-GENIE (354-3643) Please have Model information ready whencalling For Help, call 1-800-35-GENIE... -
Page 2: Warranty Information
After repairing or replacing, your Genie product, we will ship it to your home at no cost to you for parts and labor, but you will have to pay a minimum of $5.00 for shipping and IT ISCRITICALTHAT ALLSAFETY WARNINGS handling charges. -
Page 3: Safety Information
OVERVIEW OF POTENTIAL HAZARDS Garage Doorsare heavy objects that move with the help of springs under high tension and electric motors.Since moving objects,springs under tension,and electric motorscan cause injuries, your safety and thesafety of others depend on you reading the information in this man- ual. -
Page 4: Pre-Installation Checklist
ONE-PIECE DOOR, TRACKLESS Contact your Genie Factory Authorized Dealer or dealer of your Header Area garage door for any necessary bracing and a door opener reinforcement bracket (if needed) before proceeding. - Page 5 Figure 1 Checking door balance...
- Page 6 Check Step 5: HECK OWER Check Step 4: HECK EADER OUNTING NOTE Check ceiling or space above where Opener Power Head will be The header is a heavily reinforced section of the wall just mounted (Figure 5): above the top of the garage door opening. 120Volt grounded outlet or wiring box within 3 feet of Find vertical center line of door and header:...
- Page 7 Permanent wiring must be installed by a Licensed If your garage does not have a separate entry door, it is Electrician. Not all Genie Factory Authorized Dealers highly recommended to install a GenieEmergency Release Kit are Licensed Electrician's. Contact someone who is a (GER-2).
-
Page 8: Adjustments
Adjusting the beam (Figure 3). AINTENANCE AND DJUSTMENTS • Adjust the source and sensor units until the Green indicator lightsstay on. -T-B ® Step 1: LIGNING AFETY EAMS – Be sure to stay out of the path of the beam while making adjustments. - Page 9 AINTENANCE AND DJUSTMENTS WARNING Be sure the carriage is disengaged from the belt before Step ROGRAMMING EMOTE ONTROLS performing the following portion of theSafety-T-Beam® testing.The carriage is disengaged when the release WARNING lever is pointing down (Figure 4). A moving garage door may cause serious injury or death. Check the reverse function.
-
Page 10: Programming Theremote Control
PressButton again. Garage door will reverse. • SomeRemote Controls are equipped with a flashlight.The Genie logo is the button which operates the light.There is a backlight under the button. When it does not light, it AND GO OUT indicates the battery needs replaced. - Page 11 Check that the carriage is disengaged. FCC AND ICCER TIFIED • Close the garage door if not already closed • Mark the rail at the center of the carriage ( Figure 1). All devices comply with Part 15 of the FCCRules. Manually raise the door to the fully open position.FORA ONE- Operation issubject to the following two conditions: (1) PIECEDOOR,,OPEN ONLYUNTILTHEDOORISJUSTSHORTOFLEVEL.
- Page 12 Activate the opener using the remote. Adjust the close limit (Figure 3B). • • Turn the Close Limit Adjustment Screw 1/4 turn at a time Move the door in the open direction and wait for the toward the up or down to change where the bullet stops. door to stop moving (Figure 2).
- Page 13 Locate the CLOSEFORCEadjustment screw (Figure 1). Step • DJUSTING AND ESTING THE ORCE Use the remote control to cycle the door during these tests. ONTROLS ONTINUED • Start with the door open. Locate theOPENFORCEadjustment screw (Figure 3). • Turn the close force adjustment screw 1/8-turn at a time •...
- Page 14 ERIODIC AINTENANCE CHEDULE Step 7: ISENGAGING THE OOR FROM PENER ONTHLY ASKS Check the door’ s balance In case of a power failure or if the door becomes obstructed. • Close the garage door. • Pull the red carriage release knob to disengage the carriage •...
- Page 16 Have a movement and balance.Lubricate the door hardware as recommended Genie Factory Authorized Dealer make repairs to by the manufacturer. cables,spring assemblies,and other hardware.
- Page 17 PENER RUNS BY ITSELF Trouble 7: Trouble 13: HE DOOR STARTS TO CLOSE BUT REVERSESBEFORE FULL Y CLOSING Examine all remotes programmed into the opener. Check for If the opener light flashes 4 times, the close door force setting may items that might be pressing on a remote button.Look for remotes be too low.
-
Page 18: Installation Of Light Bulb
LASHING IGHT ROUBLE ODES Power Head System Status NUMBEROFFLASHES PROBLEM CAUSE REMEDY Door won’t close 2 FLASHES Shorted wall Check wall control wires.Be sure both are connected to control wire terminal screws.Check for a staple in the wires. Remove anystaplescompressing the wire. Door won’t close 3 FLASHES Safe-T-Beam®obstacle...