Page 1: Table Of Contents
Before driving Introduction Instrumentation Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Reporting safety defects (U. S. only) Index Contents...
Page 2: Introduction
Introduction ICONS Indicates a warning. Read the following section on Warnings for a full explanation. Indicates that vehicle information related to recycling and other environmental concerns will follow. We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps toward this...
Page 3 INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation.
Page 4: Instrumentation
Instrumentation Page 19 Rear window defroster control* Page 20 Power mirrors* Page 132 Hood release Page 17 Headlamp control/ Foglamp control* Page 30 Turn signal/high beam Page 6 Instrument cluster 60 70 80 0 0 0 1 2 3 0 0 0 0 x 1000 TRACTION CONTROL...
Page 5 Page 19 Instrument panel dimmer switch : I0 20 PNL/FLR PANEL FLOOR POWER AUDIO AM/FM VOLUME *if equipped On various models the appearance and location of some items may differ from those shown here. However, the page references given still apply. Page 45 Anti-theft system status indicator*...
Page 6: Turn Signal
Instrumentation TRACTION CONTROL TRACTION CONTROL INSTRUMENT CLUSTER LIGHTS AND CHIMES There are two different instrument cluster designs. The individual warning and indicator lights are described on the following pages. Turn signal Flashes when the left or right turn signal or hazard lights are activated.
Page 7 Charging system Briefly illuminates when the ignition is turned on and the engine is off. The light also illuminates when the battery is not charging properly and the vehicle may require electrical system service. Safety belt Illuminates when the ignition is switched on as a reminder to fasten the safety belts.
Page 8 Instrumentation TRACTION CONTROL x 1000 TRACTION CONTROL Low coolant (if equipped) Briely illuminates when the ignition is turned on and the engine is off. Illuminates when the engine coolant level is low. Refer to the Maintenance and care chapter to check the engine coolant level.
Page 9 O/D Off indicator (Automatic transaxle only) Illuminates and remains illuminated when the transaxle control switch (TCS) on the end of the gearshift lever is pressed and overdrive is turned off. Indicates the status of the transaxle and will flash steadily if a malfunction is detected.
Page 10: Front Foglamps
Instrumentation TRACTION CONTROL x 1000 TRACTION CONTROL Air bag readiness Briefly illuminates when the ignition is turned on. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately. Front foglamps Illuminates when foglamps are switched on.
Page 11 Brake system warning Extinguishes when the parking brake is released. Illuminates after releasing the parking brake to indicate low brake fluid level. Anti-lock brake system (ABS) (if equipped) Momentarily illuminates when the ignition is turned on and the engine is off. If the light stays on or continues to flash, the ABS needs to be serviced.
Page 12 Instrumentation TRACTION CONTROL TRACTION CONTROL Testing the warning and indicator lights and chimes Turn the ignition key to the on position without starting the engine. The following warning and indicator lights will illuminate briefly: charging system, safety belt (does not illuminate, if the driver’s safety belt is fastened), low coolant, low fuel, engine oil pressure, check engine and air bag...
Page 13 Instrumentation Headlamps on warning chime Sounds when the headlamps are on, the ignition is off (and the key is not in the ignition) and the driver’s door is open. Key-in-ignition warning chime Sounds when the key is left in the off/lock or accessory position and the driver’s door is open.
Page 14 Instrumentation TRACTION CONTROL TRACTION CONTROL INSTRUMENT CLUSTER GAUGES Tachometer (if equipped) Indicates the engine speed in revolutions per minute (rpm). 60 70 80 0 0 0 1 2 3 0 0 0 0 x 1000 BRAKE UNLEADED FUEL ONLY CHECK ENGINE 60 70 80 0 0 0 1 2 3...
Page 15 Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the NORMAL area. If it enters the red section, the engine is overheating. Switch off the ignition and determine the source of the problem. Refer to Checking and adding engine coolant in the Maintenance and care chapter.
Page 16: Fuel Gauge
Instrumentation TRACTION CONTROL x 1000 TRACTION CONTROL Fuel gauge The fuel gauge displays the approximate level of usable fuel left in the fuel reservoir. 60 70 80 0 0 0 1 2 3 0 0 0 0 BRAKE UNLEADED FUEL ONLY CHECK ENGINE 60 70 80...
Page 17: Controls And Features
TRACTION CONTROL INSTRUMENT PANEL CONTROLS Headlamp control Lamps off. Turn one position clockwise: Parking lamps, instrument panel lamps, license plate lamps and tail lamps on. Turn two positions clockwise: Headlamps on. Controls and features 60 70 80 0 0 0 1 2 3 BRAKE 0 0 0 0 x 1000...
Page 18 Controls and features Foglamp control (if equipped) Pull out the control while the headlamps are on to turn the foglamps on. Push in the control to deactivate the foglamps. Daytime running lights (DRL) (Canadian vehicles only) The DRL system turns on the highbeam headlamps, with a reduced light output, when: •...
Page 19 Controls and features Rear window defroster (if equipped) Press the defroster control to clear the rear window of thin ice and fog. The ignition must be in the on position to operate the rear window defroster. The defroster turns off automatically after 10 minutes or when the ignition is turned to the off position.
Page 20 Controls and features TRACTION CONTROL Power mirrors (if equipped) The control can be swivelled and turned. Turn the control counterclockwise to adjust the driver’s side mirror, clockwise to adjust the passenger side mirror. Adjust the selected mirror by moving the center control in the desired direction.
Page 21 Controls and features Digital clock Switch the ignition on: The clock can be set to either 12 or 24 hour format. Hours Minutes To toggle between 12 or 24 hour format, depress the H button and the M button simultaneously and then release them.
Page 22 Controls and features Climate controls Your vehicle has one of the following climate control systems: • Manual heating system • Manual heating and air conditioning system In some modes, the two systems function similarly. In modes where the systems do not function similarly, the different functions are noted.
Page 23 Temperature Turn the temperature control to the desired mix of warm or cool air (left for cooler and right for warmer). Fan speed Turn the fan speed control to the desired speed. Controlling airflow Turn the mode control to the desired airflow position.
Page 24 Controls and features Using MAX A/C mode (if equipped) The MAX A/C mode recirculates the air and directs it to flow through the instrument panel vents. This mode is noisier, but provides quicker cooling than the A/C mode. The A/C compressor only functions if the outside temperature is above 10°C (50°F).
Page 25 Using the PANEL mode The panel mode directs outside air to the panel vents. OFF mode Select the off position for all climate control functions to cease. The outside inlet door will close and the fan will shut off. Drive with the climate control system on (either in heating or A/C mode) to reduce humidity in your vehicle.
Page 26: Passenger Compartment Air Filter
Controls and features Using the FLR/DEF mode The floor/defrost mode directs outside air to flow through the floor vents and windshield defroster vents. The A/C compressor (if equipped) will function to dehumidify the windows provided the outside temperature is above 10°C (50°F).
Page 27 STEERING COLUMN CONTROLS Ignition 1. Ignition off, steering wheel locked. On vehicles with automatic transaxles, the ignition key can return to this position only if the gearshift lever is in P (Park). 2. The accessory position. Steering unlocked, radio operational. Ignition and all main electrical circuits are disabled.
Page 28 Controls and features TRACTION CONTROL Tilt steering Pull the locking lever on the steering column cover up to adjust the steering column position. Secure the wheel by pushing the locking lever down. Never adjust the steering wheel while the vehicle is moving.
Page 29 Controls and features Hazard flasher control Use only in an emergency to warn traffic of vehicle breakdown or approaching danger. Depress to activate. Depress again to switch off. The hazard lights can be operated when the ignition is off. Horn Press the pad.
Page 30 Controls and features TRACTION CONTROL Multi-function switch The turn signal functions are available only with the ignition switch on. Right turn signal Move the lever up. Left turn signal Move the lever down. Flash-to-pass Pull the lever toward you and release quickly for “flash-to-pass”...
Page 31 Windshield wipers and washer Wipers Lift the windshield wiper lever to the desired speed interval. • Intermittent: push lever up to the first position. • Low: push lever up to the second position. • High: push lever up to the third position.
Page 32 Controls and features TRACTION CONTROL Speed control (if equipped) Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. To turn speed control off • Press Off or • turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased.
Page 33 To set a speed Press Set Acc. For speed control to operate, the speed control must be on and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
Page 34 Controls and features To set a higher speed • Press and hold Set Acc. Release when the desired set speed is reached, or • press and release Set Acc. Each press will increase the set speed by 1.6 km/h (1 mph) or •...
Page 35 To return to a set speed • Press Res. For Res to operate, the vehicle speed must be faster than 48 km/h (30 mph). To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed.
Page 36 Controls and features OVERHEAD CONTROLS Interior lamps The interior lamps have three switch positions: door delay, off and on. When the control is switched to door delay (12 SEC), the interior light stays on for 12 seconds after the doors are closed with the ignition off.
Page 37 Controls and features DOOR MOUNTED CONTROLS Power door locks (if equipped) Push to lock or unlock all doors. LOCK DOOR LOCK Power windows (if equipped) The windows will only operate when the ignition is switched on. Press the appropriate control to operate the power windows at each door position.
Page 38 Controls and features Safety switch Move the switch to the right to prevent passengers from operating the windows. Move the switch to the left to allow passengers to operate the windows. Rear door childproof safety locks When the lever in the rear door lock is pushed inwards, the door can be opened only from the outside of the vehicle.
Page 39 Controls and features FLOOR MOUNTED CONTROLS Parking brake For information on the parking brake, refer to Preparing to start the vehicle in the Starting chapter. Remote luggage compartment control Pull the control located on the left of the driver’s seat to open the luggage compartment.
Page 40 Controls and features Fuel pump shut-off switch For information on the fuel pump shut-off switch, refer to Fuel pump shut-off switch in the Roadside emergencies chapter. Positive retention floor mat (if equipped) (Standard in Canada) Position the floor mat in the footwell.
Page 41 Controls and features REMOTE KEYLESS ENTRY SYSTEM (if equipped) If your vehicle has a remote entry system, you can lock and unlock the vehicle doors and open the luggage compartment without using a key. The remote also has a personal alarm feature. The remote entry feature only operates with the ignition in the off position.
Page 42 Controls and features Opening the luggage compartment Press the TRUNK control. Sounding the panic alarm Press the PANIC control. The horn will sound and the headlamps and tail lamps will flash for approximately two minutes and forty-five seconds. To deactivate the alarm, press the PANIC control again or turn the ignition key to the on position.
Page 43 Controls and features To replace the batteries: 1. Twist a thin coin between the two halves of the transmitter. Do not take the front part of the transmitter apart. 2. Remove the old batteries. 3. Place the positive (+) side of the new batteries down.
Page 44 Controls and features PASSIVE ANTI-THEFT SYSTEM (if equipped) The Passive Anti-Theft-System (PATS) is an engine immobilization system. It is an additional theft protection feature which prevents the engine from being started unless a coded key is used. This system is only available with 2.5 l engines.
Page 45 Controls and features Functional check When the ignition is switched on, : I0 20 the control light in the digital clock will illuminate for approximately three seconds to indicate that the system is operating correctly. If the control light flashes rapidly for approximately one minute and then repeatedly at irregular intervals, the system did not...
Page 46 Controls and features Key coding Replacement keys or a maximum of 15 duplicate keys can be coded. To program a key, cycle ignition switch from (3) to (1) with a programmed key. Within five seconds of this cycle, insert a new PATS key into ignition and turn to (3) or (4).
Page 47: Seating And Safety Restraints
HEAD RESTRAINTS Adjusting the head restraints Push or pull the head restraint to the desired height. Swivel the head restraint forward or backward to the desired angle. SEATING Manually adjusting the seats Pull the lever located inside the front edge of the seat to move the seat forward or backward.
Page 48 Adjusting the power seats (if equipped) Move the relevant control in the respective direction to adjust the seat, seatback and lumbar as follows: Seat (1) Forward and backward (2) Height of the entire seat (3) Height of the front of the seat (4) Height of the rear of the seat Seatback (5) Seatback inclination...
Page 49 Folding rear seats (if equipped) Pull the release knob located in the luggage compartment. Fold down the seat. The seatback cannot be released while the built-in childseat (if equipped) is open. If you are carrying objects that might damage the center rear three-point safety belt, you can unbuckle the end of the belt from the small buckle on the seat...
Page 50 Seating and safety restraints SAFETY RESTRAINTS Important safety restraints precautions The use of safety belts helps to restrain both driver and passenger in case of a collision. In most states and Canada, the law requires the use of safety belts. Front and rear seat occupants including pregnant women, should wear...
Page 51 Using safety restraints properly Combination lap and shoulder belt Insert the tongue into the slot in the buckle to fasten. Push the red release button and remove the tongue from the slot to unfasten. The passenger safety restraints in the vehicle are combination lap and shoulder belts.
Page 52 Seating and safety restraints Vehicle sensitive (emergency) locking mode The vehicle sensitive mode is the normal retractor mode which locks the belts in response to vehicle movement. For example, if the driver brakes suddenly, turns a corner sharply or your vehicle receives an impact of 8 km/h (5 mph) or more the combination safety belts will lock to help reduce...
Page 53 Seating and safety restraints Using automatic locking mode The automatic locking mode must be used when installing a child safety seat in any passenger seat. 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder belt portion and pull downward until the entire belt is extracted.
Page 54 Seating and safety restraints Front seat safety belt height adjustment Position the shoulder belt height adjuster so that the belt rests across the middle of your shoulder. Be sure the shoulder belt is properly positioned on your shoulder each time you use the belt. If the shoulder belt is off your shoulder, on your upper arm or neck, there is a greater risk of severe injury in...
Page 55 Seating and safety restraints Center position three-point safety belts If the lower end of the belt has been unbuckled, pull the belt steadily from the reel and insert the small tongue into the small buckle until a distinct “click” is heard.
Page 56 Seating and safety restraints Conditions of operation If the driver’s safety belt is not buckled before the ignition key is turned to on, the safety belt indicator illuminates for 1-2 minutes and the warning chime sounds for 4-8 seconds. If the driver’s safety belt is buckled while the indicator light is illuminated and the reminder chime is sounding, the safety belt...
Page 57: Care Of Safety Belts
Care of safety belts Periodically check the belts for damage or fraying. Check the security of the anchorage points and the locking action of the inertia reels by giving each belt a sharp tug. Belts subjected to strain, as in the result of an accident, should be replaced and the anchorages checked by your dealer or a...
Page 58 Seating and safety restraints x 1000 TRACTION CONTROL AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to: • work with the safety belt to protect the driver and right front passenger.
Page 59 Do not attempt to service, repair, or modify the air bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags For additional important safety information, read all information on safety restraints in this guide.
Page 60 Seating and safety restraints How does the air bag supplemental restraint system (SRS) work? The SRS is designed to activate when the vehicle is in a collision, similar to hitting a fixed barrier head on at 12-24 km/h (8-14 mph). The fact that the air bags did not inflate in a collision does not mean that something is wrong with the...
Page 61 Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag is inflated, air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Page 62 Seating and safety restraints Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a chime to indicate the condition of the system. Refer to the Air bag readiness section in the Instrumentation chapter. Routine maintenance of the air bag is not required.
Page 63 Seating and safety restraints Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or a qualified technician. Air bags MUST BE disposed of by qualified personnel.
Page 64 Seating and safety restraints CHILDREN AND SAFETY RESTRAINTS To prevent the risk of injury, make sure children sit where they can be properly restrained. Whenever possible, put children in one of the rear seats in your vehicle. Accident statistics indicate that children are safer when properly restrained in the rear seats than in the front seats.
Page 65 Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children.
Page 66 Seating and safety restraints Children and safety belts Children who are too large for child safety seats (as specified by the child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraints and air bag precautions that apply to adult passengers in your vehicle.
Page 67 Seating and safety restraints To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt- positioning booster seat that is labelled as conforming to all federal motor vehicle safety standards.
Page 68 Seating and safety restraints Built-in child seats Built-in child safety seat (if equipped) The rear seat may include a built-in child seat. This child seat conforms to all Federal and local motor vehicle safety standards. Read the labels located on the child seat cushion and shoulder belt for information on the built-in child seat.
Page 69 Seating and safety restraints Child seat interlock safety feature The interlock ensures that a child is not placed in the integrated child seat when the folding seatback is not securely latched. It prevents the seatback from being unlatched while the child seat is in use.
Page 70 Seating and safety restraints Placing your child in the built-in child seat Failure to follow all of the instructions on the use of this child restraint system can result in your child striking the vehicle’s interior during a sudden stop or crash. Never use the built-in child seat as a booster cushion with the adult safety belts.
Page 71 Seating and safety restraints 3. Read all the information and warnings on the child seat cushion and shoulder safety belt. Make sure the child is not too large for the child seat. 4. If connected, squeeze the tabs on the top and bottom of the chest clip and pull the halves apart to open the chest clip.
Page 72 Seating and safety restraints 6. Insert either the left or the right safety belt tongue into the single opening of the crotch safety belt buckle (it doesn’t matter which tongue is inserted first). Insert the other tongue. The color green must appear in the indicator window on each tongue when buckled.
Page 73 If the child seat was in use during a collision, Ford recommends replacing it. Built-in child restraints not in use during a collision should be inspected and replaced if either damage or improper operation is noted.
Page 74 Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 75 Installing child safety seats in combination lap and shoulder belt seat positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. When using forward-facing child seats move the passenger seat as far back from the instrument panel as possible.
Page 76 Seating and safety restraints 4. Insert the belt tongue into the proper buckle for that seating position until you hear and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt...
Page 77 Seating and safety restraints 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. 10.
Page 78 Tether anchor hardware Tether anchor hardware kits (part number 613D74), including instructions, may be obtained at no charge from any Ford or Lincoln- Mercury dealer. All vehicles built for sale in Canada include a tether anchor hardware kit.
Page 79: Starting
IMPORTANT SAFETY PRECAUTIONS A computer system controls the engine’s idle revolutions per minute (rpm). When the engine starts, the idle rpm runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked by your dealer or a qualified service technician.
Page 80 Starting Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. IMPORTANT VENTILATION INFORMATION If the engine is idling while the...
Page 81 Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle...
Page 82 Starting PREPARING TO START THE VEHICLE Engine starting is controlled by the spark ignition system. This system meets all Canadian Interference- Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator pedal before or during starting.
Page 83 If starting a vehicle with an automatic transaxle: • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). If starting a vehicle with a manual transaxle: • Make sure the parking brake is set.
Page 84 Starting 3. Turn the key to the on position (without turning the key to start). Make sure the following lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced by your dealer or a qualified service technician. •...
Page 85 Starting STARTING THE ENGINE 1. Turn the key to the start position (4) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to the on (3) position. 2. If the engine does not start within five seconds, wait ten seconds and try again.
Page 86 Starting USING THE ENGINE BLOCK HEATER (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater- defroster system to respond quickly. It is strongly recommended if you live in a region where temperatures reach –23°C (–10°F) or below.
Page 87: Driving
Driving BRAKES Your brakes are self-adjusting. Refer to the “Service Guide” for maintenance intervals. Anti-lock braking system (ABS) (if equipped) The ABS operates by detecting the onset of wheel lock up during brake applications and compensating for this tendency. The wheels are prevented from locking even when the brakes are firmly applied, helping to ensure that the vehicle can be steered and...
Page 88 Driving Braking with ABS • In an emergency, apply full force on the brake pedal. In vehicles with manual transaxles, you must also depress the clutch pedal. The anti-lock braking system will be activated immediately, allowing you to retain full steering control of your vehicle and, providing there is sufficient space, will enable you to avoid...
Page 89 Parking brake To engage the parking brake: Pull the handle upward. To release the parking brake: 1. Press and hold the release button. 2. Pull the handle upward to disengage the brake. 3. Push handle downward to the off position. Always set the parking brake fully and make sure that the gearshift is securely latched in P...
Page 90 Driving TRANSAXLE OPERATION Automatic transaxle (if equipped) Vehicles equipped with an automatic transaxle are equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from the P (Park) position unless the brake pedal is depressed. Putting your vehicle in gear You must push the thumb button to move the gearshift to the position you choose.
Page 91 Driving Overriding the brake-shift interlock feature If it is necessary to use this procedure to move the gearshift lever, it is possible that a fuse has blown and the vehicle’s brakelamps may not be working. Refer to Fuses and relays in the Roadside emergencies chapter.
Page 92 Driving The console-mounted gearshift will lock when you turn the key to the lock position. When the gearshift is in any position except P (Park), the ignition key cannot be turned to lock or removed from the steering column. To remove the key, the gearshift lever must be in P (Park).
Page 93 Driving • N (Neutral) The wheels of the transaxle are not locked. Your vehicle will roll freely, even on the slightest incline, unless the parking brake or brakes are on. • D (Overdrive) Note that the vehicle’s gearshift is console-mounted on the floor. The transaxle control switch (TCS) is located on the gearshift handle.
Page 94 Driving • D (Drive) D (Drive) provides more engine braking than overdrive and is useful when driving through hilly terrain or if your vehicle requires additional power for climbing hills. Activate by pressing the transaxle control switch (TCS) located on the gearshift handle.
Page 95 Driving • 2 (Second) Use the 2 (Second) position to start up on slippery roads or to provide additional braking on downgrades. When your vehicle is in 2 (Second), it automatically starts off in second gear. Do not go faster than 90 km/h (55 mph) in this gear.
Page 96 Driving Manual transaxle (if equipped) Vehicles equipped with a manual transaxle have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. Using the clutch When starting a vehicle with a manual transaxle: 1. Hold down the brake pedal. 2.
Page 97 Recommended shift speeds 2.0 litre engine 5-speed transaxle Recommended upshifts: Shift from First to second Second to third Third to fourth Fourth to fifth 2.5 litre engine 5-speed transaxle Recommended upshifts: Shift from First to second Second to third Third to fourth Fourth to fifth *The vehicle can be shifted at lower speeds to improve fuel economy.
Page 98 Driving Parking 1. Apply the brake and the clutch and shift into neutral. 2. Engage the parking brake. 3. Shift into 1 (First) or R (Reverse). 4. Turn the ignition off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone.
Page 99 Driving LOADING YOUR VEHICLE Before loading your vehicle, familiarize yourself with these terms. Base curb weight Weight of the vehicle including any standard equipment, fluids and lubricants. It does not include passengers or aftermarket equipment. Payload Combined maximum allowable weight of passengers, cargo and optional equipment.
Page 100 Driving GVWR (Gross Vehicle Weight Rating) Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Compliance Certification Label on the driver’s door pillar. GAWR (Gross Axle Weight Rating) Carrying capacity for each axle system (front and rear).
Page 101 Payload = GVWR minus Base curb weight To obtain the correct weight for your vehicle, try taking your vehicle to a shipping company or an inspection station for trucks. Do not use replacement tires with lower weight capacities than the originals because they might lower the vehicle’s GVWR and GAWR.
Page 102 Driving It is extremly dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 103 454 kg (1 000 lb) trailer. Your vehicle does not come from the factory fully equipped to tow. No towing packages are available through Ford or Lincoln/Mercury dealers. Trailer towing puts additional loads on your vehicle’s engine, transaxle, axle, brakes, tires, and suspension.
Page 104 Driving Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’s load limits. • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter. • Use extra caution when driving while trailer towing. Refer to Driving while towing a trailer in this chapter.
Page 105 Do not exceed the maximum loads listed on the Safety Compliance Certification Label. For load specification terms found on the label, refer to Loading your vehicle in this chapter. Remember to figure in the tongue load of your loaded vehicle when figuring the total weight.
Page 106 Driving Using a hitch Do not use hitches that: • Clamp onto the vehicle bumper. • Attach to the axle. Distribute the load so that only 10 to 15% of the total weight of the trailer is on the tongue. Tie down the load so that it does not shift and change weight on the hitch.
Page 107 Using trailer brakes Use electric brakes or manual, automatic or surge type hydraulic brakes that meet Federal and local regulations. Install and adjust brakes according to the manufacturer’s instructions. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system.
Page 108 Driving Driving while towing a trailer Do not drive faster than 72 km/h (45 mph) while towing a 454 kg (1 000 lb) trailer. Do not drive faster than 72 km/h (45 mph) with any weight trailer while towing in hilly terrain or on hot days.
Page 109 FUEL CONSUMPTION Fuel economy can be improved by avoiding: • lack of regular, scheduled maintenance, • excessive speed, • rapid acceleration, • driving with the brake pedal depressed, • sudden stops, • extended engine idling, • use of speed control in hilly terrain, •...
Page 110: Roadside Emergencies
Roadside emergencies HAZARD FLASHER CONTROL Use only in an emergency to warn traffic of vehicle breakdown or approaching danger. Depress to activate. Depress again to switch off. The hazard lights can be operated when the ignition is off. FUEL PUMP SHUT-OFF SWITCH If the engine cranks, but does not start or does not start after a collision, the fuel pump shut-off...
Page 111 If you see or smell fuel, do not reset the switch or try to start your vehicle. Have all the passengers get out of the vehicle and call the local fire department or a towing service. If your engine cranks but does not start after a collision or substantial jolt: 1.
Page 112 Roadside emergencies FUSES AND RELAYS If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire. Check the appropriate fuses before replacing any electrical components. Always replace a fuse with one that has the specified amperage rating.
Page 113 Power distribution box To check or replace a fuse or a relay, remove the cover of the fuse box in the engine compartment by releasing the latch (1) and lifting A blown fuse can be identified by a break in the wire. Use the fuse puller (2) attached to the cover of the power distribution box to change a fuse.
Page 114 Roadside emergencies Power distribution box Ampere Fuse rating — — * Have these fuses replaced by your dealer or qualified technician. (engine compartment) Color Circuits protected black Main power supply to vehicle electrical system yellow Engine cooling fan yellow ABS braking system, heater blower yellow Ignition and EEC module...
Page 115 Power distribution box (engine compartment) Circuits switched Relay Daytime running lights Radiator fan relay (high speed) Air conditioning Air conditioning clutch relay Radiator fan relay (low speed) Starter solenoid Horn Electrically operated fuel pump Low beam headlamps R 10 High beam headlamps R 11 EEC module Reverse voltage protection...
Page 116 Roadside emergencies A blown fuse can be identified by a break in the wire. Use the fuse puller (2) attached to the cover of the power distribution box to change a fuse. All fuses are a push fit. Five reserve fuses with different current ratings are attached to the inside cover of the power distribution box in case of...
Page 117 Passenger compartment fuse panel (below instrument panel) Ampere Fuse Color rating — black orange brown light blue light blue yellow brown light blue light green light green brown brown brown brown brown brown light green — Roadside emergencies Circuits protected —...
Page 118 Roadside emergencies Standard fuse amperage ratings and colors Fuse rating 3 amp 7.5 amp 10 amp 15 amp 20 amp 30 amp 30 amp fuse link 40 amp 60 amp fuse link 80 amp fuse link 100 amp fuse link Auxiliary relays (outside of fuse boxes) Relay Circuits switched...
Page 119 Roadside emergencies CHANGING TIRES Park your vehicle in such a position that neither the traffic nor you are hindered or endangered when changing the tire. Ensure that the vehicle is on firm, level ground. If necessary, secure your vehicle further by blocking the wheels with chocks.
Page 120 Roadside emergencies The temporary spare tire The vehicle may have a high pressure temporary spare tire. This spare is smaller than a regular tire and is designed for emergency use only. This tire should be replaced as soon as possible. If you use the temporary spare tire continuously or do not follow these precautions, the...
Page 121 Roadside emergencies Spare tire location The spare tire and tools are located under the floor cover in the luggage compartment. Removing the spare tire and tools 1. Raise the rear of the floor cover in the luggage compartment and fold it forward. 2.
Page 122 Roadside emergencies Tire changing procedure Removing a tire 1. Apply the parking brake and 1 (first) gear (manual transaxle) or the P (Park) position (automatic transaxle). 2. Activate the hazard flashers. 3. The driver and all passengers must leave the vehicle. 4.
Page 123 Roadside emergencies Replacing a tire 1. Push the spare tire onto the wheel studs. 2. Screw on the wheel nuts, ensuring the tapered end of the wheel nuts are facing the wheel, and secure in a clockwise direction. 3. Lower the vehicle and remove the jack by turning the handle counterclockwise.
Page 124 Roadside emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. For further information, see cables in the index.
Page 125 Connecting jumper cables 1. Position the vehicles so that they do not touch one another. 2. Switch off the engine. Switch off any unnecessary electrical equipment. 3. Connect the positive (+) terminal of the discharged battery to the positive (+) terminal of the booster battery (1).
Page 126 Roadside emergencies Jump starting 1. Start the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the vehicle with the discharged battery. 3. Once the engine has been started, run both vehicles for an additional three minutes before disconnecting the cable leads.
Page 127 If towing is necessary, it is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with slingbelt equipment. Ford Motor Company has not developed or approved a T-hook or slingbelt towing procedure. TOWING YOUR VEHICLE...
Page 128: Maintenance And Care
• We provide you with a “Service Guide” which makes tracking routine service for your vehicle easy. If your vehicle requires professional service, your Ford dealership can provide necessary parts and service. Check your “Warranty Guide” to find out which parts and services are covered.
Page 129 Precautions when servicing your vehicle Be especially careful when inspecting or servicing your vehicle. Here are some general precautions for your safety: • Do not work on a hot engine. The cooling fan is automatic and may come on at any time.
Page 130 Maintenance and care Working with engine off (automatic transaxle) 1. Set the parking brake fully and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly.
Page 131 Working with engine on (automatic transaxle) 1. Set the parking brake fully and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly. Do not start your engine with the air cleaner removed and do not remove it while the engine is running.
Page 132 • Pull the handle (1) located under the instrument panel. • Release the safety catch by reaching under the hood (2) (adjacent to the Ford emblem) and pushing it up. • Raise the hood and support it with the strut (3) in the yellow colored retainer, ensuring it is secure.
Page 133 2.0 litre EFI-engine compartment Power Engine steering coolant reservoir reservoir Windshield Engine oil washer fluid dipstick reservoir For ease of identification, all filler caps and the engine oil dipstick are marked yellow/black. Maintenance and care Automatic Brake fluid transaxle reservoir dipstick (if equipped) Engine oil...
Page 134 Maintenance and care 2.5 litre EFI-engine compartment Power Engine steering coolant reservoir reservoir Windshield Engine oil washer fluid dipstick reservoir For ease of identification, all filler caps and the engine oil dipstick are marked yellow/black. Automatic Brake fluid transaxle reservoir dipstick (if equipped) Engine oil...
Page 135 Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by Ford Warranty. Checking the engine oil Check the engine oil each time you fuel your vehicle.
Page 136 Maintenance and care 6. If the oil level is below the minimum line, add engine oil as necessary. If the oil level is beyond the maximum line, engine damage or high oil consumption may occur and some oil must be removed from the engine by a service technician.
Page 137 Refer to the ”Maintenance Schedule” booklet for additional information. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application. Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for...
Page 138 MIN mark, the brake fluid level warning light on the instrument panel will illuminate. Add only brake fluid that meets the Ford specification (see the chapter Capacities and specifications). Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes.
Page 139 Engine coolant maintenance Checking and adding engine coolant Check the level of the coolant in the reservoir at least once a month. Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked for a long period of time, the engine coolant reservoir may eventually empty.
Page 140 Ford recommends Ford Premium Cooling System Fluid, which is an optimized formula that will protect all metals and rubber elastomers used in Ford engines for four years or 80 000 km (50 000 miles). It is neither necessary nor recommended to use supplemental coolant additives in your gasoline- powered vehicle.
Page 141 Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specifications ESE- M97B44-A, and use of such coolant may harm engine and cooling system components.
Page 142 Maintenance and care Adding engine coolant 1. Before removing the engine coolant recovery cap, turn the engine off and allow it to cool. 2. When the engine is cool, turn and remove the cap. Never remove the coolant recovery cap while the engine is running or hot.
Page 143 Maintenance and care Severe winter climate If you drive in extremely cold climates (less than -36°C [-34°F]), it may be necessary to increase the coolant concentration above 50%. Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle is such that the coolant will not freeze at the temperature level in...
Page 144 Maintenance and care Automatic transaxle fluid Check the automatic transaxle fluid according to the scheduled intervals in the “Service Guide”. However, if the transaxle is not working properly (slipping, shifting slowly or fluid leakage) the fluid level should be checked. Adding automatic transaxle fluid Before adding any fluid, make sure...
Page 145 Maintenance and care Checking the automatic transaxle fluid With the vehicle on a level surface and the brake fully applied, start the engine and move the gearshift lever through all of the gears. Securely latch the lever in P (Park). Set parking brake and leave the engine running.
Page 146 Maintenance and care Battery Your vehicle may be equipped with a Motorcraft maintenance-free battery. The Motorcraft maintenance-free battery normally M o t o r does not require additional water c r a f t during its life of service. However, S U P E R S T A R T for severe service usage or in high...
Page 147 Maintenance and care Battery replacement If your original equipment battery requires replacement while under warranty, it will be replaced with a Motorcraft service battery, identical in design technology. Like the original equipment battery, it should not require water addition during its normal life of service; however, for severe service usage or in high temperature climates, check your battery electrolyte...
Page 148 Maintenance and care Applying too much pressure on the ends when lifting a battery could cause acid to spill. Lift the battery with a carrier or with your hands on the opposite corners. Batteries normally produce explosive gases which can cause personal injury.
Page 149 Relearning the idle function Because your vehicle’s engine is electronically controlled, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the computer must “relearn” its idle conditions before your vehicle can drive properly.
Page 150 Traces of grease, silicone and fuel prevent wiper blades from functioning properly. We recommend Ford cleaning solutions or equivalent to clean wiper blades. Change the wiper blades on your vehicle at least once a year.
Page 151 Maintenance and care 2. Remove the plastic caps from the screws on the grille. Remove the screws. 3. Open the hood. Pull off the rubber weatherstrip at the back of the engine compartment. Remove the screws that hold the grille, separate the two halves and remove the grille.
Page 152 Title 49 Code of Federal Regulation Part 575.104(c)(2). U.S. Department of Transportation – Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.
Page 153 Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire grade of 150 would wear one and one-half (1 1/2) times as well on the government course as a tire grade 100.
Page 154 Maintenance and care Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excess temperature can lead to...
Page 155 Checking tire pressure Check the tire pressure periodically and inflate the tires as necessary. To check the tire pressure, insert the tire pressure gauge into the valve. The cold pressure amount is listed on the Safety Compliance Certification label. Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly resulting in loss of vehicle control.
Page 156 Maintenance and care Replacing tires Replace tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial, bias- belted, or bias-type tires. Use only the tire sizes that are listed on the tire pressure decal.
Page 157 Dispose of worn tires in accordance with local environmental regulations. Refer to the Safety Compliance Certification label to determine the specific size tire and wheel Ford Motor Company recommends for use on this vehicle. When purchasing replacement tires for your vehicle, consult your...
Page 158 However, in some climates, using snow tires and chains may be necessary. Ford offers snow chains as a Ford approved accessory and recommends use of these or their equivalents on approved tires. See...
Page 159 • Drive cautiously. If you hear the chains rub or bang against the vehicle, stop and retighten them. If this does not work, remove the chains to prevent vehicle damage. • Local regulations may prohibit or restrict the use of tire chains. Investigate the laws and regulations in your area before installing chains.
Page 160 Maintenance and care IMPORTANT FUEL INFORMATON Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision.
Page 161 Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Make sure the fuel cap is correctly fitted after fueling. Failure to do so may cause the on board diagnostic system to illuminate the CHECK ENGINE...
Page 162 Maintenance and care Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. The damage may not be covered by your warranty. Your vehicle was not designed to use fuel containing manganese- based additives such as MMT.
Page 163 Maintenance and care Octane recommendations Your vehicle is designed to use MINIMUM OCTANE RATING regular gasoline with an (R+M)/2 (R+M)/2 Method octane rating of 87. We do not recommend gasolines labeled as “regular” in high altitude areas that are sold with octane ratings of 86 or even less.
Page 164 Cleaner air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates such as a maximum of 10% ethanol or 15% MTBE. There...
Page 165 Maintenance and care Calculating fuel economy To accurately calculate your vehicle’s fuel economy: 1. Fill the tank completely and record the initial odometer reading. 2. Each time you fill the tank, record the amount of fuel added (in litres or gallons). 3.
Page 166 Maintenance and care WHAT YOU SHOULD KNOW ABOUT THE EMISSION CONTROL SYSTEM For more information about your vehicle’s emission control system, refer to the Vehicle Emission Control Information Decal located on the inside, left of the engine compartment. The catalytic converter enables the vehicle’s emission control system to operate properly.
Page 167 If you notice one or more of the following, the emission system may not be functioning properly; have the vehicle serviced as soon as possible: • Fluid leaks. • The charging system, engine oil pressure or low coolant warning lights illuminate in the instrument cluster and remain lit.
Page 168 Maintenance and care Important emission control imformation By law, anyone who manufactures, repairs, services, leases, trades vehicles or supervises a fleet of vehicles is not permitted to intentionally remove an emission control device or prevent it from working. Do not make any unauthorized changes to the vehicle or engine.
Page 169 Preparing your vehicle for inspection/maintenance (I/M) testing In some localities it may be a legal requirement to pass an I/M test of the on-board diagnostic(OBD) II system. If your vehicle’s powertrain system or battery has just been serviced, the OBD II system is reset to a condition unready for I/M testing.
Page 170 Maintenance and care BULB REPLACEMENT Removing the headlamps assembly Handle a halogen headlamp bulb carefully and keep out of children’s reach.Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
Page 171 Maintenance and care Reinstalling the headlamp assembly The gasket lining must be seated properly around the lamp assembly when reinstalling. All bulb connectors must be correctly connected. Install in the reverse order. Headlamps – low beam Disconnect the electrical connector and replace the bulb.
Page 172 Maintenance and care Front turn signal/side lamps Pull the socket out. Pull the bulb out and replace it. Foglamps (if equipped) 1. Detach the cover (access at bottom of front bumper). 2. Turn the bulb counterclockwise and pull it out of the light assembly. 3.
Page 173 Maintenance and care Brake/turn signal/tail lamps 1. Disconnect the electrical conector. 2. Turn the socket counterclockwise and pull it out. 3. Turn the bulb counterclockwise and pull it out. 4. To install, fit the new bulb in reverse order. Backup lamps The backup lamps are located in the trunk lid.
Page 174 Maintenance and care High-mounted brake lamp Enter the rear seat compartment. Unscrew both screws and remove the complete lamp assembly. Bend the housing outwards to unclip the lamp module. Press the reflector fitting from the four locking points and pull it off. Pull out the wedge base bulb and replace.
Page 175 Interior lamps Switch off the interior lamps (middle switch position). Pry out the lamp assembly with a flat screwdriver, release the reflector at the side and replace the festoon bulb. To install, fit the new bulb in reverse sequence. Reading lamps (if equipped) Open the lamp assembly.
Page 176 Maintenance and care AIMING THE HEADLAMPS The alignment of your headlamps should be checked if: • Oncoming motorists frequently signal you to deactivate your high beams, and your high beams are not activated. • The headlamps do not seem to provide enough light for clear night vision.
Page 177 Maintenance and care The horizontal aim must be adjusted first. You will need one 7 mm box wrench, open end wrench or T-15 Torx drive. The following procedures assumes that the vehicle’s front structure is properly aligned. If the vehicle has been in an accident requiring the front end of the vehicle to be repaired, the horizontal indicator...
Page 178 Maintenance and care Adjusting the vertical aim The numbers shown on the vial indicate beam direction in degrees up or down. 1. Do not adjust the vertical aim until after adjusting the horizontal aim. 2. With the hood open, locate the bubble level vertical aim indicator.
Page 179 Maintenance and care VEHICLE CARE Washing your vehicle Only use car washing areas that have environmentally friendly drainage systems. Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent.
Page 180 Maintenance and care During winter months, it is especially important to wash the vehicle on a regular basis. Large quantities of dirt and road salt are difficult to remove, and they also cause damage to the vehicle. Remove or lower any exterior accessories, such as antennas, before entering a car wash.
Page 181 Maintenance and care Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up paint, paint repair foil or aerosol spray from the Ford accessories line. Observe the application instructions on the products. Cleaning the wheels...
Page 182 Maintenance and care Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup act as insulators and keep the engine warmer than normal. Follow these guidelines to clean your engine: • Take care when using a power washer to clean the engine.
Page 183 Maintenance and care Cleaning plastic exterior parts Use a vinyl cleaner for routine cleaning of plastic. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps Wash the exterior lamps with the same detergent you use to wash the exterior of your vehicle.
Page 184 Maintenance and care Cleaning the instrument panel Clean the instrument panel with a damp cloth, then dry with a dry cloth. Any cleaner or polish that increases the gloss of the upper portion of the instrument panel should be avoided. The dull finish in this area is to help protect the driver from undesirable windshield reflection.
Page 185 Cleaning and caring for your vehicle Refer to the “Customer Assistance Guide” for a list of Ford-approved cleaners, polishes and waxes. Maintenance and care...
Page 186: Capacities And Specifications
Capacities and specifications Motorcraft parts Component Spark plug* Air filter Passenger compartment air filter Fuel filter Oil filter Battery PCV valve Crankcase ventilation filter * Refer to Vehicle Emission Control Information (VECI) decal for spark plug and gap specifications. ** If a spark plug is removed for examination, it must be reinstalled in the same cylinder. If a spark plug needs to be replaced, use only spark plugs with the service part number suffix letter “FE”...
Page 187 Capacities Engine oil - with filter - without Manual transaxle Automatic transaxle with oil cooler Power steering Cooling system with heating Windshield washer fluid Fuel tank Braking system * Total capacity ** with automatic transaxle Capacities and specifications 2.0 litre engine 4.25 l (4.5 qts) 3.75 l (4.0 qts)
Page 188 Capacities and specifications Lubricant Specifications Ford part name Item or equivalent High performance Brake fluid DOT 3 brake fluid Premium engine Engine coolant Motorcraft motor Engine oil oil 5W-30 super Power steering power steering fluid Transaxle fluid automatic/ MERCON 5-speed manual...
Page 189 Engine data Engine Capacity Power output Nm (lb-ft) Max. torque Fuel required Continuous engine speed Max. intermittent engine speed Idle speed (manual transaxle) Mixture preparation Firing order Spark plug gap Ignition system Valve Inlet clearances Exhaust * Mechanical valve adjuster Capacities and specifications 2.0 litre Engine...
Page 190 Capacities and specifications Dimensions A = Maximum length B = Overall width (without mirrors) C = Overall height (curb weight) D = Wheelbase E = Track * Dependent on tire size mm (inches) 1380 - 1427 (54.3 - 56.2) Front 1499 - 1518* (59.0 - 59.8) Rear 1483 - 1502* (58.4 - 59.1)
Page 191 Capacities and specifications VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is attached to a metal tag and is located on the front driver’s side of the instrument panel. The VIN tag may be seen by looking through the windshield from the outside of the vehicle.
Page 192: Reporting Safety Defects (U. S. Only)
National Highway Traffic Safety Administration (NHTSA) in addition to Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 193: Index
Accessory position on the ignition ....27 Additives, engine oil ..135 Air bag supplemental restraint system and child safety seats .
Page 194 Index Child safety restraints built-in child seat ...68 child safety seats ... .74 children and safety belts . . .64, 66 Child safety seats and air bags .
Page 195 Engine oil changing oil and filter ..136 checking and adding ..135 dipstick ....133 disposal .
Page 196 Index High-mount brakelamp ..174 Hood latch location ....132 release lever ....132 Horn .
Page 197 Maintenance (see Servicing) Manual transaxle backing up (reverse) ..98 clutch .....96 fluid, capacity ... . .187 fluid, checking and adding .
Page 198 Index Safety belts (see Safety restraints) Safety chains, when towing a trailer ....107 Safety Compliance Certification Label ..... .105 Safety defects, reporting .
Page 199 Tires changing ....122 checking tire pressure ..155 cleaning ....181 inspection and maintenance .
Page 200: Filling Station Information
Fuel filler location UNLEADED FUEL ONLY Octane 87 61.5 litres (16.3 gallons) Use Motorcraft 5W-30 Formula E Fuel Economy Motor Oil, Ford specification WSS-M2C153-G. Refer to Safety Compliance Certification label on driver’s door pillar Pull handle under the left side of...

This manual is also suitable for:

Contour 1998

Ford 1998 Contour Manual

Quick Links

Related Manuals for Ford 1998 Contour

Summary of Contents for Ford 1998 Contour

This manual is also suitable for:

Table of Contents