Page 1 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Copyright 1998 Ford Motor Company Contents...
Page 2: Introduction
Introduction ICONS Indicates a safety alert. Read the following section on Warnings. Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment.
Page 3 Introduction INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. SPECIAL NOTICES Notice to owners of Cobra vehicles Before you drive your vehicle, be sure to read the “SVT Cobra Owner’s Guide Supplement.”...
Page 4: Instrumentation
Instrumentation Headlamp control (pg. 16) Turn signal and wiper/washer control (pg. 44) Instrument cluster (pg. 6) Driver side air bag (pg. 74)
Page 5 Instrumentation Climate control systems (pg. 18) Electronic sound system (pg. 21)
Page 6: Warning Lights And Chimes
Instrumentation WARNING LIGHTS AND CHIMES Base instrument cluster Optional instrument cluster Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster, check for a burned-out turn signal bulb.
Page 7 Instrumentation High beams Illuminates when the high beam headlamps are turned on. Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Charging system Illuminates when the ignition is turned to...
Page 8 Instrumentation Service engine soon Your vehicle is equipped SERVICE ENGINE with a computer that SOON monitors the engine’s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). The OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
Page 9 consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required. If the Service Engine Soon light remains on, have your vehicle serviced at the first available opportunity. Light is blinking: Engine misfire is occurring which could damage your catalytic converter.
Page 10 Instrumentation Traction Control active This light momentarily illuminates when the ignition is turned to ON. It also illuminates when the Traction Control system begins applying and releasing the brakes and adjusting the engine characteristics to limit a wheelspin condition. It will be lit for a minimum of four seconds or for the duration of the Traction Control event.
Page 11: Headlamps On Warning Chime
and more needs to be added. This lamp will also illuminate when the ignition is turned to ON and the engine is off. For more information on adding engine coolant, refer to Engine coolant in the Maintenance and care chapter. Safety belt warning chime Chimes to remind you to fasten your safety belts.
Page 12: Fuel Gauge
Instrumentation Optional instrument cluster gauges Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
Page 13: The Vehicle
Never remove the coolant reservoir cap while the engine is running or hot. This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate.
Page 14: Trip Odometer
Instrumentation Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer at the top of the scale or in the red zone may damage the engine. Base instrument cluster Standard instrument cluster Trip odometer Registers the kilometers (miles) of individual journeys.
Page 15 Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’s electrical system checked as soon as possible. Engine oil pressure gauge This shows the engine oil pressure in the...
Page 16: Controls And Features
Controls and features HEADLAMP CONTROL Pull the headlamp control toward you to the first position to turn on the parking lamps, tail lamps, license plate lamps and marker lamps. Pull the headlamp control toward you to the outer position to turn on the headlamps (in addition to the previous lamps).
Page 17 PANEL DIMMER CONTROL To adjust the brightness of the instrument panel: Rotate clockwise/ counterclockwise when the headlamp control is in the parking lamp or low-beam position. To turn on the courtesy lamps: Rotate fully counterclockwise. REAR WINDOW DEFROSTER (IF EQUIPPED) The rear defroster control is located on the instrument panel.
Page 18: Fan Speed Control
Controls and features CLIMATE CONTROL SYSTEM Manual heating and air conditioning system Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Page 19 Under normal conditions, your vehicle’s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. In snowy or dirty conditions, leave the mode selector in the OFF position when the ignition is turned off.
Page 20 Controls and features the windshield defroster ducts. If the temperature is about 10°C (50°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging. -Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield.
Page 21: Volume Control
top of your instrument panel. These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system. Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop. USING YOUR AUDIO SYSTEM AM/FM Stereo/Cassette/Premium Sound FM 1...
Page 22 Controls and features AM/FM select The AM/FM select control works in radio mode and allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. Tune adjust in radio mode Tune adjust allows you to tune in a particular radio station.
Page 23 Seek function in tape mode The Automatic Music Search (AMS) feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection. Press the AMS control. Press to listen to the previous selection on the tape.
Page 24 Controls and features Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is...
Page 25 Press (+) or (−) on the volume control to increase or decrease treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Push the AUDIO control repeatedly until the display reads BAL. Press the (+) side of the volume control to shift sound to the right speakers.
Page 26 Controls and features Rewind/fast forward The rewind and fast forward controls work in tape mode. Rewind/fast forward function in tape mode Press rewind the tape. Play will continue once the beginning of the tape is reached or rewind is stopped. Press to fast forward the tape.
Page 27 AM/FM Stereo/Cassette/MACH 460 Sound System with Premium AM/FM Stereo Cassette POWER AUDIO AM/FM VOLUME Power control Press the control to turn the audio system on or off. Volume control Press the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 28 Controls and features Tune adjust Tune adjust works in radio mode and allows you to manually tune in a particular radio station. Press the SCAN/TUNE button twice. The display reads TUNE. Press the SEEK control to move up or down through the frequencies.
Page 29 Press to listen to the next selection on the tape. Scan function The scan function works in radio, tape and CD mode (if equipped). Scan function in radio mode This feature allows you to scan the frequency band, stopping on each listenable station for approximately a five-second sampling.
Page 30 Controls and features Press to scan forward selections. Press the SCAN/TUNE button again to stop the scan mode on the current selection. Radio station memory preset The radio is equipped with five station memory preset controls. These controls can be used to select up to five preset AM stations and ten FM stations (five in FM1 and five in FM2).
Page 31 Push the AUDIO control repeatedly until the display reads TREB. Press (+) or (−) on the volume control to increase or decrease treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Push the AUDIO control repeatedly until the display reads BAL.
Page 32 Controls and features Tape play select Insert a cassette tape into the cassette deck. Push only slightly when inserting a cassette tape (with the open edge to the right). A cassette deck loading mechanism pulls the tape in the rest of the way.
Page 33: Setting The Clock
Setting the clock Press the CLOCK control while simultaneously depressing the SEEK control. Press to set the hours. Press to set the minutes. Premium AM/FM Stereo Single CD Radio/Premium Sound or MACH 460 Sound System with Single CD Radio POWER EJECT COMP AM/FM...
Page 34 Controls and features wish to maintain your preset volume level, turn the audio system off with the power control before switching off the ignition. AM/FM select The AM/FM select control works in radio mode and allows you to select AM or FM frequency bands.
Page 35 Seek function in radio mode Press to find the next listenable station down the frequency band. Press to find the next listenable station up the frequency band. Scan function The scan function works in radio mode. Scan function with compact disc radio Press the SCAN/ TUNE control once.
Page 36 Controls and features CLOCK 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. If the battery is disconnected, the memory preset stations will need to be reset. Automatic memory store (if equipped) Automatic memory store allows you to set strong radio stations without losing your original manually...
Page 37 Push the AUDIO control repeatedly until the display reads BAL. Press the (+) side of the volume control to shift sound to the right speakers. Press the (−) side of the volume control to shift sound to the left speakers. Speaker fade adjust Speaker sound distribution can be adjusted between the front and rear speakers.
Page 38 Controls and features Press the control for more than three seconds for fast forward action. CD eject Press the control to stop and eject a CD. If a disc is ejected from the CD player but is not removed within approximately 10 seconds, the player will automatically reload the disc for storage (unless the disc is automatically ejected because it was inserted upside down, in which case the disc...
Page 39: Stop Function
Single Disc CD Player (if equipped) EJECT Power and volume control The compact disc player operates when the audio system is on and a CD is inserted (label side up). The volume is controlled by the VOLUME control on the audio system. Play function The system enters the PLAY mode when a CD...
Page 40 Controls and features Scan function Press the SCAN control SCAN to enter the scan mode. The CD player will begin scanning the CD, stopping on each listenable track for approximately eight seconds. This continues until you press the SCAN control a second time or eject the CD.
Page 41 Compression adjust brings soft and loud CD passages together for a more consistent listening level. Shuffle feature The shuffle feature plays all tracks on the current CD in random order. Press the SHUFFLE control to start this feature. Random order play will continue until the control is pressed again.
Page 42 Controls and features The player’s internal temperature is above 60°C (140°F). Allow the player to cool down before operating. A disc with format and dimensions not within industry standards is inserted. Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge.
Page 43 Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.9, 88.1–107.1, 107.9 MHz Not all frequencies are used in a given area.
Page 44 Controls and features Audio system warranties and service Refer to the “Warranty Guide” for audio system warranty information. If service is necessary, see your dealer or a qualified technician. TRUNK REMOTE CONTROL Press the remote trunk release control located in the glove compartment.
Page 45 Mist Function To operate the Mist function of the windshield wipers, push and release the windshield washer control quickly. The wipers will cycle one or two times. HIGH BEAMS Push forward to activate. FLASH TO PASS Pull toward you to activate and release to deactivate.
Page 46 Controls and features 5. START, cranks the engine. Release the key as soon as the engine starts. TILT STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the...
Page 47 To turn speed control off Press OFF or Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed Press SET/SET ACC/ SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle...
Page 48 Controls and features To set a higher set speed Press and hold SET/ SET ACC/SET ACCEL. Release the control when the desired vehicle speed is reached or Press and release SET/SET ACC/SET ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or Accelerate with your accelerator pedal.
Page 49 To disengage speed control Depress the brake pedal or Depress the clutch pedal (if equipped) Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. To return to a previously set speed Press RES/RSM/ RESUME.
Page 50 Controls and features INTERIOR LAMPS Map lamps (if equipped) If equipped with a convertible top the map lamps and controls are located on the rearview mirror. Press the controls on either side of each map lamp to activate the lamps. POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows.
Page 51 Controls and features Express down To make the driver window open fully without holding the window control, press the driver window control completely down and release quickly. Depress again to stop window operation. Window lock The window lock feature allows only the driver to operate the power windows.
Page 52 Controls and features 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in.
Page 53 Controls and features Foglamp control (if equipped) Turn on the parking lamps or the low-beam headlamps. Press the top portion of the foglamp control, located on the center console, to activate the foglamps. The foglamp LED will illuminate when the foglamps are on. Press the bottom portion of the foglamp control to deactivate the foglamps.
Page 54 Controls and features 2. Check the convertible top stowage compartment behind the rear seat to be sure it is empty and ready to receive the top. 3. Unclamp the top from the windshield header at both the right and left sides by pulling each clamp rearward until the hook in the windshield header is free.
Page 55 Controls and features 2. Push boot forward until rear attachment engages under molding. 3. Push forward flap of boot until both clips engage under trim panel edge. Repeat on other side of vehicle. 4. Tuck side attachments under molding. Repeat on other side of vehicle.
Page 56 Controls and features Raising the convertible top The convertible top will not operate unless the parking brake is engaged. Do not raise the top while the vehicle is moving because the top may be severely damaged. To raise the convertible top: 1.
Page 57 confirms that the vehicle is locked with a short “beep” from the horn. The remote entry features only operate with the ignition in the OFF position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting.
Page 58 Controls and features Opening the trunk Press the control once to open the trunk. Ensure that the trunk is closed and latched before driving your vehicle. Failure to latch the trunk may cause objects to fall out of the trunk or block the rear view. Sounding a panic alarm Press this control to activate the alarm.
Page 59 The inside lights will not turn off if: they have been turned on with the dimmer control or any door is open. The battery saver will shut off the interior lamps 30 minutes after the ignition has been turned to the OFF position, 10 minutes after if the door is left open, and 30 minutes after if the trunk is left open or the dome lamp switch is left on.
Page 60 Controls and features weather conditions nearby radio towers structures around the vehicle other vehicles parked next to the vehicle To replace the batteries: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER...
Page 61 The SecuriLock compatible with aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Large metallic objects or devices such as the Mobil Speedpass on the same key ring as your SecuriLock key may cause vehicle starting problems.
Page 62 Controls and features Programming spare SecuriLock Spare SecuriLock your dealership and programmed to your SecuriLock passive anti-theft system (up to a total of 8 keys). Your dealership can program your new SecuriLock key(s) to your vehicle or you can do it yourself using the following simple procedure.
Page 63 4. Turn the ignition to OFF and remove the second SecuriLock key from the ignition. 5. Within 10 seconds of turning the ignition to OFF, insert the unprogrammed SecuriLock key/valet key) into the ignition and turn the ignition from OFF to RUN (maintain ignition in RUN for at least one second).
Page 64: Seating And Safety Restraints
Seating and safety restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 65 Seating and safety restraints Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
Page 66 Seating and safety restraints Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Using the power lumbar support (if equipped) The power lumbar control is located on...
Page 67 Seating and safety restraints Using the manual lumbar support (if equipped) The lumbar control is located on the inboard side of the driver’s seatback. Move the control up to increase firmness and down to decrease firmness. Rear seat entry/exit Use the seatback release to fold the back of the front seat forward for rear seat passenger entry or exit.
Page 68 Seating and safety restraints 2nd seat/Split-folding rear seat (if equipped) One or both rear seatbacks can be folded down to provide additional cargo space. To lower the seatback(s) from inside the vehicle, pull tab to release seat back and then fold seatback down.
Page 69 Seating and safety restraints It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 70 Seating and safety restraints 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Page 71 Seating and safety restraints The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode When a tight lap/shoulder fit is desired. Anytime a child safety seat is installed in a passenger front or outboard rear seating position (if equipped).
Page 72 Seating and safety restraints Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Page 73 (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a...
Page 74 Seating and safety restraints Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. Refer to Cleaning and maintaining the safety belts in the Maintenance and care section. AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS)
Page 75 Seating and safety restraints All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag SRS is provided. Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.
Page 76 Seating and safety restraints Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags For additional important safety information, read all information on safety restraints in this guide.
Page 77 Seating and safety restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation.
Page 78 Seating and safety restraints considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control.
Page 79 Seating and safety restraints A difficulty with the system is indicated by one or more of the following: The readiness light will either flash or stay lit. The readiness light will not illuminate immediately after ignition is turned on. A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and light are repaired.
Page 80 Do not leave children, unreliable adults, or pets unattended in your vehicle. To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor...
Page 81 Seating and safety restraints seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child. A belt-positioning booster should be used if the shoulder belt rests in front of the child’s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the...
Page 82 Refer to Automatic locking mode (passenger side front and outboard rear seating positions)(if equipped). Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 83 Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions If you must use a forward facing child seat in the front seat (reminder children 12 years old and unders should always be properly restrained in the rear seat).
Page 84 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction...
Page 85 Tether anchorage hardware Attachment holes (at each rear seating position) have been provided in your vehicle to attach anchor hardware, if desired. Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or...
Page 86 Seating and safety restraints Lincoln-Mercury dealer. All vehicles built for sale in Canada include a tether anchor hardware kit. Be sure to follow the child safety seat manufacturer’s instructions. Tighten the anchor according to specifications. Otherwise, the safety seat may not be properly secured and the child may be injured in a sudden stop or collision.
Page 87: Starting
PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine.
Page 88 Starting Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Do not allow the vehicle to idle for more than ten minutes at high engine RPM.
Page 89 3. Turn the key to 4 (ON) without turning the key to 5 (START). Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver’s safety belt is fastened, the may not illuminate. 60 70 RPMX1000 80 100 120...
Page 90 Starting STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 2. If the temperature is above –12°C (10°F) and the engine does not start within five seconds on the first try, turn the key to OFF, wait ten seconds and try again.
Page 91 Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes.
Page 92: Driving
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 93 The ABS operates by detecting the onset of wheel lockup during brake applications and compensating for this tendency. The wheels are prevented from locking even when the brakes are firmly applied. The accompanying illustration depicts the advantage of an ABS equipped vehicle (on bottom) to a non-ABS equipped vehicle (on top) during hard braking with loss of front braking traction.
Page 94 Driving stopping distance. Always leave enough room between your vehicle and the vehicle in front of you to stop. We recommend that you familiarize yourself with this braking technique. However, avoid taking any unnecessary risks. Hydraulic brake booster system (Hydroboost) The Hydroboost system receives fluid pressure from the power steering pump to provide power assist during braking.
Page 95 (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First Gear) (manual transmission). The parking brake is not recommended to stop a moving vehicle.
Page 96 Driving controlled by automatically applying and releasing the rear brakes in conjunction with engine torque reductions. Engine torque reduction is realized via the fully electronic spark and fuel injection systems. This process is very sensitive to driving conditions and very fast acting. The rear wheels “search” for optimum traction several times a second and adjustments are made accordingly.
Page 97 To prevent damage to the power steering pump: Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running. Do not operate the vehicle with a low power steering pump fluid level.
Page 98 Driving Do not drive your vehicle until you verify that the brakelamps are working. If your vehicle gets stuck in mud or snow it may be rocked out by shifting from forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear.
Page 99 P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift is securely latched in P (Park). This position locks the transmission and prevents the rear wheels from turning. Always set the parking brake fully and make sure the gearshift is securely latched in P...
Page 100 Driving N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through four.
Page 101 instrument cluster. Transmission operates in gears one through three. braking than (Overdrive) and is useful when: driving with a heavy load towing a trailer up or down steep hills additional engine braking is desired. If towing a trailer, refer to Driving while you tow in the Trailer Towing chapter.
Page 102 Driving MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch Vehicles equipped with a manual transmission have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. When starting a vehicle with a manual transmission, you must: 1.
Page 103 Recommended shift speeds Do not downshift into 1 (first) when your vehicle is moving faster then 24 km/h (15 mph). This will damage the clutch. Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) 1 - 2 2 - 3 3 - 4 4 - 5...
Page 104 Driving 4. Turn the ignition key to position 3 (OFF). Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Reverse You can shift into R (Reverse) only by moving the gearshift to the right of 5 (Fifth) gear before you shift into R (Reverse).
Page 105 gearshift back into Neutral. Then, release the clutch pedal for a moment and repeat steps 2 through 4. Removing key from ignition Turn the ignition key to position 3 (OFF). Push the release lever forward and rotate the key towards you and remove.
Page 106 Driving VEHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: Base Curb Weight: Weight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include passengers or aftermarket equipment. Payload: Combined maximum allowable weight of cargo, passengers and optional equipment.
Page 107 Maximum Trailer Weight: maximum weight of a trailer the loaded vehicle (including passengers and cargo) is permitted to tow. It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle. Trailer Weight Range: Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating.
Page 108 Driving Always ensure that the weight of passengers, cargo and equipment being carried is within the weight limitations that have been established for your vehicle including both Gross Vehicle Weight and Front and Rear Gross Axle Weight Rating limits. Under no circumstance should these limitations be exceeded.
Page 109 If you use a rental trailer, follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type brakes are safe if installed properly and adjusted to the manufacturer’s specifications.
Page 110 Driving Exceeding the GCWR rating may cause internal transmission damage and void your warranty coverage. Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your Scheduled Maintenance guide for more information.
Page 111 Driving DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall. Water may also enter your engine’s air intake and severely damage your engine.
Page 112: Hazard Flasher
Roadside emergencies HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. The hazard lights control is located on top of the steering column.
Page 113 Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4.
Page 114 Roadside emergencies Standard fuse amperage rating and color Fuse Mini Rat- Fuses Grey Violet Pink 7.5A Brown Blue Yellow Natural Natural Green — — — — — Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal.
Page 115: Cigar Lighter
OWNERS The fuses are coded as follows: Fuse/Relay Fuse Amp Location Roadside emergencies MANUAL FUSE Rating Cigar Lighter Engine Controls — Not Used RH Low Beam Headlamp Instrument Cluster, Traction Control Switch Starter Motor Relay GEM, Interior Lamps Engine C ontrols —...
Page 116 Roadside emergencies Fuse/Relay Fuse Amp Location Rating — Not Used Speed Control Servo, Shift Lock Actuator Electronic Flasher Power Mirror Switch, GEM, Anti-Theft Relay, Power Door Locks, Door Ajar Switches Convertible Top Switch Instrument Cluster and Engine Control Memory — Not Used A/C Clutch, Defogger Switch...
Page 117 Fuse/Relay Fuse Amp Location Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Page 118: Power Distribution Box
Roadside emergencies GUIDE The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Location Relay 1 Relay 2 Relay 3 Relay 4 Relay 5 (4.6L), 30A CB (3.8L) CONSULTER MANUAL OWNERS Rating — Fog Lamp Interrupt — Int. Wiper — Wiper HI/LO —...
Page 119 Fuse/Relay Fuse Amp Location * Mini Fuses ** Maxi Fuses CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Roadside emergencies Rating 20A**...
Page 120 Roadside emergencies Temporary spare tire information Your vehicle may have a temporary spare tire. The temporary spare tire for your vehicle is labeled as such. It is smaller than a regular tire and is designed for emergency use only. Replace this tire with a full-size tire as soon as possible.
Page 121 Roadside emergencies 1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park) or R (manual transmission), turn engine OFF, and block the diagonally opposite wheel. 3. Remove the spare tire, jack and lug wrench.
Page 122 Roadside emergencies Never use the rear differential as a jacking point. To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack.
Page 123 (not the dealer) to get a replacement key. If the lug wrench/lug nut key assembly is lost, see your nearest Ford or Lincoln/Mercury dealer who has access to the master set of keys. Do not use an impact wrench with the anti-theft key.
Page 124 Roadside emergencies Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted. Do not attempt to push start your vehicle. Automatic transmissions do not have push-start capability.
Page 125 Roadside emergencies Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 126 Roadside emergencies 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. The preferred locations of an exposed metal part (to ground the circuit) are the alternator mounting brackets or an engine lifting eye.
Page 127 Roadside emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery. 3.
Page 128 Roadside emergencies 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 129 It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If your vehicle is to be towed from the rear using...
Page 130: Maintenance And Care
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
Page 131 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift in 1 (First). 3. Turn off the engine and remove the key. 4.
Page 132 Maintenance and care OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. HOOD 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.
Page 133 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.8L OHV V6 engine 1. Engine oil filler cap 2. Engine oil dipstick 3. Brake fluid reservoir 4. Power distribution box 5. Windshield washer fluid reservoir 6. Battery 7. Power steering fluid reservoir 8.
Page 134 Maintenance and care 4.6L SOHC V8 engine 1. Engine oil dipstick 2. Brake fluid reservoir 3. Power distribution box 4. Windshield washer fluid reservoir 5. Battery 6. Engine coolant reservoir 7. Power steering fluid reservoir 8. Engine oil filler cap 9.
Page 135 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4.
Page 136 Maintenance and care If the oil level is below the MIN mark, add enough oil to raise the level within the MIN—MAX range. Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician.
Page 137 Ford material and design specifications, startup engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application. BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed.
Page 138 3. If necessary, add brake fluid until the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter.
Page 139 Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail. CLUTCH ADJUSTMENT (IF EQUIPPED) Check the clutch adjustment.
Page 140 Maintenance and care WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way.
Page 141 ENGINE COOLANT 3.8L OHV V6 engine 4.6L V8 engine Check the level of the engine coolant in the reservoir. Refer to the Scheduled Maintenance Guide for service interval schedules. Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become empty.
Page 142 E2FZ-19549–AA (in Oregon, F5FZ-19549–CC, in Canada, Motorcraft CXC-10) or a premium engine coolant that meets Ford specification ESE-M97B44–A. DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544–AA (orange in color). DO NOT USE a DEX-COOL engine coolant or an equivalent engine coolant that meets Ford specification WSS-M97B44–D.
Page 143 Change your engine coolant according to the appropriate schedule listed in the Scheduled Maintenance Guide. Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44–A, and...
Page 144 Maintenance and care Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter.
Page 145: Checking Power Steering Fluid Level
Maintenance and care If your vehicle is equipped with the 3.8L V6 engine, check the power steering fluid level with the engine at normal operating temperature. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near...
Page 146 Maintenance and care If your vehicle is equipped with a 4.6L V8 engine, check the power steering fluid level with the engine at ambient temperature. Allow at least one-half hour after driving for the power steering fluid to cool. 1. Start the engine and allow the engine to idle.
Page 147 Maintenance and care been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature.
Page 148 Maintenance and care could result when the vehicle reaches normal operating temperature. The transmission fluid should be in this range if at normal operating temperature (66°C-77°C [150°F-170°F]). The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result...
Page 149 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
Page 150 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules.
Page 151 Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation. When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting...
Page 152 Maintenance and care 4. The relearning process will automatically complete as you drive the vehicle. The vehicle may need to be driven 16 km (10 miles) or more to relearn the idle and fuel trim strategy. If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
Page 153: To Replace The Wiper Blades
10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information...
Page 154: Treadwear
Maintenance and care about tire grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Page 155 Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.
Page 156 Maintenance and care 15 or 16 inch four tire rotation 17 inch four tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads.
Page 157 Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.), as originally offered by Ford. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over.
Page 158 Maintenance and care The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. Use chains on the tires only in an emergency or if the law requires them.
Page 159 The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel...
Page 160 Maintenance and care Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. Fuels can also be harmful if absorbed through the skin.
Page 161 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If...
Page 162 Maintenance and care If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel system to work improperly in a collision, which may result in possible personal injury. Choosing the right fuel Use only UNLEADED FUEL.
Page 163 Cleaner air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates up to 10% ethanol or 15% MTBE. Running out of fuel Avoid running out fuel because this situation may have an adverse affect on powertrain components.
Page 164 Maintenance and care ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy.
Page 165 Use a known quality gasoline, preferably a national brand. Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent.
Page 166 Maintenance and care Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy. Habits Smooth, moderate operation can yield up to 10% savings in fuel.
Page 167 Combine errands and minimize stop-and-go driving. Maintenance Keep tires properly inflated and use only recommended size. Operating a vehicle with the wheels out of alignment will reduce fuel economy. Use recommended engine oil. Refer to Lubricant Specifications. Perform all regularly scheduled maintenance items.
Page 168 If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 169 Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the charging system warning light, “Service Engine Soon” light or the temperature warning light, fluid leaks, strange odors, smoke or loss of oil pressure, could indicate that the emission control system is not working properly.
Page 170 Maintenance and care If the vehicle’s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition. To ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: First, at least 10 minutes of driving on an expressway or highway.
Page 171 Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
Page 172 Maintenance and care To install the new bulb: 1. With the flat side of the new bulb’s plastic base facing upward, insert the glass end of the bulb into the lamp assembly. You may need to turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly.
Page 173 Maintenance and care 5. Rotate the bulb socket counterclockwise about ⁄ turn and remove from lamp assembly. 6. Carefully pull the bulb straight out from the socket and push in the new bulb. 7. To complete installation, follow the removal procedure in reverse order.
Page 174 Maintenance and care 1. Rotate the foglamp bulb counterclockwise and remove from foglamp (the rear side of the foglamp is shown). 2. Disconnect the electrical connector from the foglamp bulb. 3. Connect the electrical connector to the new foglamp bulb. 4.
Page 175 Map lamps For bulb replacement, see a qualified service technician or your dealer. Using the right bulbs Function Tail lamp, brakelamp, turn lamp Park lamp, turn lamp, side marker (front) Backup lamp License plate lamp High-mount brakelamp Headlamps Luggage compartment lamp Dome lamp Map lamp Visor vanity lamp...
Page 176 6. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUSTABLE. 7. Close the hood and turn off the lamps. CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes.
Page 177 Maintenance and care Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results.
Page 178 Ultra Touch Prep and Finishing Kit (#F7AZ-19K507–BA), touch-up paint (#ALBZ-19500–XXXXA), or aerosol paint spray (#ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring.
Page 179 Cover the highlighted areas to prevent water damage when cleaning the engine. Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary.
Page 180 Dry with a soft cloth. For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label.
Page 181 Convertible top and padded molding care To avoid damage to the vinyl top and moldings, use only an approved Ford cleaner, or equivalent. Do not use stiff bristle brushes or abrasive materials or cleaners. Hot waxes applied by commercial car washes can affect the cleanability of vinyl material.
Page 182: Capacities And Specifications
Capacities and specifications MOTORCRAFT PART NUMBERS Component Air filter element Fuel filter Battery Oil filter PCV valve Spark plugs* * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. **If a spark plug is removed for inspection, it must be reinstalled in the same cylinder.
Page 183: Refill Capacities
Capacities and specifications REFILL CAPACITIES Fluid Ford Part Name Brake fluid High Per- formance DOT 3 Motor Vehicle Brake Fluid Engine oil Motorcraft (includes 5W-30 filter Super change) Premium Motor Oil Engine Premium coolant Engine Coolant Power Motorcraft steering MERCON...
Page 184 Washer Concentrate Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. Rear axle lubricants do not need to be checked or...
Page 185 Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface. LUBRICANT SPECIFICATIONS Item Ford part name Brake fluid High Per- formance DOT 3 Motor...
Page 186 Capacities and specifications Item Ford part name Engine Ford coolant Premium Engine Coolant Engine oil Motorcraft 5W-30 Super Premium Motor Oil Lock Penetrating cylinders and Lock Lubricant Power Motorcraft steering MERCON fluid and convertible top fluid (if equipped) Rear axle...
Page 187 Add 118 ml (4 oz.) of additive friction modifier C8AZ-19B546–A, Ford specification EST-M2C118–A for complete refill of Traction-Lok axles. Ford design rear axles contain a synthetic lubricant that does not require changing unless the axle has been submerged in water.
Page 188 Capacities and specifications ENGINE DATA Engine Cubic inches Horsepower Torque Required fuel Firing order Spark plug gap Ignition system Compression ratio VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear 1 358.9 mm (53.5 in) for Mustang GT...
Page 189 Capacities and specifications...
Page 190: Certification Label
The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped). MFD. BY FORD MOTOR CO. IN U.S.A. DATE: XXXXX GVWR:XXXXX LB/ XXXXX KG FGAWR: XXXXXX/XXXXXXX...
Page 191: Customer Assistance
80,000 km (50,000 miles) on Lincoln vehicles In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln-Mercury dealer. Roadside assistance will cover: changing a flat tire...
Page 192 There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage. (In Hawaii, rules vary. See your dealer for details.)
Page 193 Ford. At Ford Motor Company and Ford of Canada, we are dedicated to providing Ford, Lincoln and Mercury vehicle owners with programs that will enhance your ownership experience and protect you from unexpected repair bills.
Page 194 Customer assistance general manager of the dealership. In most cases, your concern will be resolved at this level. Ford Motor Company and Ford of Canada dealerships also carry genuine Ford parts and accessories, providing you with original equipment reliability. Away from home...
Page 195 Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Page 196 West Virginia, Georgia and Wisconsin purchasers/lessees. Board membership The Board consists of: three consumer representatives a Ford or Lincoln/Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln-Mercury dealership management, recognized for their business leadership qualities.
Page 197 DSB’s independent administrator Your dealership and a Ford Motor Company representative are asked to submit statements at this time. To properly review your case, the Board needs the...
Page 198 Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 199 Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. In the United States, using leaded fuel may also result in difficulty importing your vehicle back into the U.S.
Page 200 Ford Motor Company Worldwide Direct Market Operations. FORD ACCESSORIES FOR YOUR VEHICLE Ford has many quality products available from your dealer to clean your vehicle and protect its finishes. For best results, use the following or products of equivalent quality:...
Page 201 Ford’s rigid engineering and safety specifications. Ford accessories are warranted for up to 12 months or 20,000 km (12,000 miles) on all cars and light trucks and 12 months with unlimited distance on...
Page 202 Customer assistance Travel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adaptors Fog lights Framed luggage covers Heavy-duty battery Neutral towing transfer case kit (Explorer 4.0L only) Off road lights Pickup box rails Removable luggage rack Removable luggage rack adapters Retractable bed hooks and loops Running boards...
Page 203 Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers (full and mini) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rallye bars Rear air deflectors Rear decklid spoilers Side window air deflectors Spare tire lock Step bumpers Step/sill plates...
Page 204 (Citizens band [CB] transceivers, garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your vehicle’s operation.) Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment.
Page 205 Monday-Friday 8:00 a.m. - 6:00 p.m. EST, for credit card holders only To order the publications in this portfolio in Canada: Make cheques payable to: Ford Motor Company of Canada, Ltd. Service Publications P.O. Box 1580, Station B Mississauga, Ontario, Canada L4Y 4G3 or order toll free: 1-800-387-4966 Monday-Friday 8:00 a.m.
Page 206: Reporting Safety Defects
National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 207: Index
Air bag supplemental restraint system ... 74 and child safety seats ... 76 description ... 74 disposal ... 79 driver air bag ... 77 indicator light ... 7,78 operation ... 77 passenger air bag ... 77 Air cleaner filter ... 182 Air conditioning ...
Page 208 ... 142 low coolant light ... 10 refill capacities ... 144,183 specifications . 185,188 Customer Assistance 191 Ford accessories for your vehicle ... 200 Ford Extended Service Plan ... 192 Getting assistance outside the U.S. and Canada ... 199 Getting roadside assistance ...
Page 209 Fluid capacities ... 183 Foglamps ... 53 Fuel ... 158 calculating fuel economy ... 164 cap ... 161 capacity ... 183 choosing the right fuel ... 162 comparisons with EPA fuel economy estimates ... 168 detergent in fuel ... 163 filling your vehicle with fuel ..
Page 210 Index Infant seats (see Safety seats) ... 81 Inspection/maintenance (I/M) testing ... 169 Instrument panel ... 6 cleaning ... 180 lighting up panel and interior ... 17 location of components ... 6 Jump-starting your vehicle ... 123 Keys key in ignition chime ...
Page 211 Power distribution box (see Fuses) ... 117 Power door locks ... 51 Power steering ... 96 fluid, checking and adding ... 144 fluid, refill capacity ... 183 fluid, specifications . 185,188 Radio ... 21 Relays ... 113 Remote entry system ... 56,58 illuminated entry ...
Page 212 Index Traction control ... 95 active light ... 10 Traction-lok rear axle ... 105 Transmission automatic operation ... 97 fluid, checking and adding (automatic) ... 146 fluid, checking and adding (manual) ... 149 fluid, refill capacities ... 183 lubricant specifications ... 188 manual operation ..
Page 215: Filling Station Information
Information Unleaded fuel only - 87 octane 58.7L (15.5 gallons) 4.7L (5.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford specification WSS-M2C153-G Refer to the Certification Label. Pull handle under the left side of the instrument panel. 11.2L (11.8 quarts) 13.3L (14.1 quarts)
Page 216 Filling station information Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface.

This manual is also suitable for:

1998 mustang gt

Ford 1999 Mustang Owner's Manual

Quick Links

Related Manuals for Ford 1999 Mustang

Summary of Contents for Ford 1999 Mustang

This manual is also suitable for:

Table of Contents