Page 1 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Copyright 1998 Ford Motor Company...
Page 2: Introduction
INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation.
Page 3 Do not use this vehicle for snowplowing. Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance Preparation package. Notice to owners of utility type vehicles Before you drive your vehicle, please read this Owner’s Guide carefully.
Page 4: Instrumentation
Instrumentation Instrument panel dimmer switch (pg. 18) Headlamp control (pg. 17) PEDALS Power adjustable foot pedals* (pg. 18) Rear window defroster control (pg. 19) Instrument cluster (pg. 6) DOOR AJAR km/h Speed control (pg. 49) Turn signal and wiper/washer control (pg.
Page 5: Climate Control Systems
Electronic sound system Gearshift (includes overdrive button) (pg. 113) VOL-PUSH ON SEEK TUNE DISCS A4WD 4WD control * (pg. 115) Instrumentation (pg. 20) FM 1 FADE AUTO BASS TREB DOLBY 8 NR SCAN TAPE CD SIDE 1-2 COMP SHUFFLE PANEL COOL WARM Climate control systems...
Page 6 Instrumentation WARNING LIGHTS AND CHIMES FUEL SERVICE ENGINE SOON FUEL DOOR Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge. The light comes on when there is approximately 1/16th of a tank indicated on the fuel gauge (refer to Fuel Gauge in this chapter for more information).
Page 7 What you should do if the Service Engine Soon light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2.
Page 8 Instrumentation Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Brake system warning Momentarily illuminates when the BRAKE ignition is turned to the ON position, the engine is off and the...
Page 9 High beams Illuminates when the high beam headlamps are turned on. SecuriLock anti-theft system This light indicates the anti-theft alarm system is armed. Momentarily illuminates when the ignition is turned to ON/START. If the light fails to illuminate, continues to flash or remains on, have the system serviced.
Page 10 Instrumentation Four wheel drive low (if equipped) This light momentarily illuminates when the ignition is turned to ON. Illuminates when four-wheel drive RANGE low is engaged. If the light continues to flash have the system serviced. Four wheel drive indicator (if equipped) This light momentarily illuminates when the ignition is turned to ON.
Page 11: Headlamps On Warning Chime
Fuel reset Illuminates when the ignition is turned to the ON position and the fuel pump shut-off switch has been triggered. For more information, refer to Fuel pump shut-off switch in the Roadside emergencies chapter. Safety belt warning chime Chimes to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter.
Page 12 Instrumentation Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
Page 13 Never remove the coolant reservoir cap while the engine is running or hot. This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. If the gauge enters the red section, the oil pressure/engine coolant and Check Engine/Service Engine Soon indicators illuminate, refer to What you should know about fail-safe cooling in the Maintenance and care chapter.
Page 14 Instrumentation Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’s electrical system checked as soon as possible. Engine oil pressure gauge This shows the engine oil pressure in the system.
Page 15 Selectable features English/metric display Press this control to change the trip computer display from metric to English units. Press again to change from English to metric units. Mode control Each press of the MODE control will display a different feature as follows: Compass display.
Page 16 Instrumentation Average fuel economy. The display will indicate the vehicle’s average fuel economy in liters/100 km (or miles/gallon) since last reset. To reset the average fuel economy: 1. Press the MODE control repeatedly until AVG F/ECON is displayed (no other display is resettable).
Page 17: Controls And Features
HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: the engine must be running and the headlamp control is in the OFF or Parking lamps position.
Page 18 Controls and features PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. Rotate up to brighten. Rotate down to dim. Rotate to full down position to turn off. AUTOLAMP CONTROL The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
Page 19 Never adjust the accelerator and brake pedal with feet on pedals or while the vehicle is moving. REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog.
Page 20 Controls and features USING YOUR AUDIO SYSTEM Premium AM/FM Stereo/Cassette/Premium Sound (CD Changer Compatible) PUSH ON TAPE MUTE MACH Audio System with Premium AM/FM Stereo/ Cassette (CD Changer Compatible) PUSH ON TAPE MUTE TUNE SEEK SIDE 1 . 2 SEEK TUNE SIDE 1 .
Page 21 Your vehicle is equipped with a delayed accessory feature. This feature enables the audio playing media to continue playing up to 10 minutes after the ignition has been turned off, or until a door is opened. Volume/power control Press the control to turn the audio system on or off.
Page 22 Controls and features to increase volume compensation to decrease or shut off the volume compensation AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped). AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
Page 23 Press to select the next disc in the CD changer. Hold the control to fast-forward through the remaining discs. Seek function The seek function control works in radio, tape or CD mode (if equipped). Seek function in radio mode Press to find the next listenable station down the frequency band.
Page 24 Controls and features Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again.
Page 25 If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. To deactivate autoset and return to your audio system’s manually set memory stations, press the control again. Bass adjust The bass adjust control allows you to increase or decrease the audio...
Page 26 Controls and features Tape/CD select To begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function.
Page 27 Eject function Press the control to stop and eject a tape. Dolby noise reduction Dolby noise reduction operates only in tape mode. Dolby reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby noise reduction. The noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation.
Page 28 Controls and features The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend FM radio broadcasters to use RDS technology to transmit information. FM radio stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired. Press the RDS control.
Page 29 Oldies R & B Religious Rock Soft Top 40 Show With RDS activated, press the RDS control until SHOW is displayed. Use the SEL control to select TYPE, NAME or NONE. RDS clock feature Refer to Setting the clock for information. Mute mode Press the control to mute the playing media.
Page 30 Controls and features Use the SEL control to select the desired signal mode (the selected mode will appear in the display). The following signal modes can be selected: JAZZ CLUB—jazz club with clearly reflected sounds. HALL—rectangular concert hall capacity of about 2 000 CHURCH—church with a high vault.
Page 31 Rear seat controls (if equipped) The rear seat controls allow the middle seat passengers to operate the radio, tape, CD or CD changer (if equipped). To turn on the rear seat controls, press the memory preset controls 3 and 5 at the same time. The appear in the display.
Page 32 Controls and features Turning the speakers on and off Press to turn all speakers on or off. Using headphones Plug a 3.5 mm headphone (not included) into the speaker on/off control to operate the headphones. The rear speakers will cut out once the speaker on/off control is pressed. The front speaker will remain playing for the front passengers.
Page 33 Memory preset control Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2. Push the MEMORY control in CD changer mode (if equipped) to advance to the next disc. Seek function In radio mode, press the next listenable station down...
Page 34 Controls and features 2. Press to eject the magazine. 3. Turn the magazine (A) over. 4. Using the disc holder release knob (C), pull the disc holder (B) out of the magazine. If you pull too hard on the disc holder, the disc holder may come completely out of the magazine.
Page 35 5. Line up the CD with the groove of the disc holder. Ensure that the label on the CD faces downwards. 6. Press in on the disc holder until it locks securely into the magazine. If the disc holders are not fully locked into the magazine, the unit will not operate.
Page 36 Controls and features The player’s internal temperature is above 60°C (140°F). Allow the player to cool down before operating. A disc with format and dimensions not within industry standards is inserted. Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge.
Page 37 Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.9, 88.1–107.1, 107.9 MHz Not all frequencies are used in a given area.
Page 38 Controls and features CLIMATE CONTROL SYSTEM Manual heating and air conditioning system Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Page 39 Controls and features MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster. Airflow will be from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle.
Page 40 Controls and features Operating tips In humid weather, select DEF your windshield from fogging. After a few minutes, select any desired position. To prevent humidity buildup inside the vehicle, don’t drive with the climate control system in the OFF position. Don’t put objects under the front seat that will interfere with the airflow to the back seats (if equipped).
Page 41 Turning the EATC on Press AUTOMATIC, any of the override controls or the fan speed control. The EATC will only operate when the ignition is in the ON position. Turning the EATC off Press OFF. The Outside Temperature function will continue to operate until the ignition is turned off.
Page 42 Controls and features Temperature selection The display window indicates the ˚ selected temperature, function AUTO (AUTO or one of the override controls) and manual control of fan speed ( ) if automatic fan speed is not desired. To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer)
Page 43 Fan speed ( When AUTOMATIC is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, use the thumbwheel or steering wheel control to cancel automatic fan speed operation. Rotate the thumbwheel up for higher fan speed or down for lower fan speed.
Page 44 Controls and features MAX A/C-Uses recirculated air to cool the vehicle. The temperature will display 16°C (60°F). To exit, press AUTOMATIC or any other override controls. MAX A/C is noisier than normal A/C but more economical and will cool the inside of the vehicle faster. Airflow is from the instrument panel registers.
Page 45 Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again. If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to the window.
Page 46 Controls and features Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield). If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
Page 47 In order for the auxiliary A/C-heater controls to function, the driver’s auxiliary A/C-heater control must be set to REAR. The instrument panel climate controls must be on in order for the auxiliary A/C-heater to operate. When the auxiliary A/C-heater control is set to FLOOR, airflow only occurs from the third row seat floor vent located in the driver’s side rear quarter trim panel.
Page 48 Controls and features Anywhere between PANEL and FLOOR to vary airflow between the outlets. POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal.
Page 49 SPEED CONTROL To turn speed control on Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on.
Page 50 Controls and features To set a speed Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
Page 51 You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. To set a lower set speed Press and hold CST/COAST. Release the control when the desired speed is reached or Press and release CST/COAST.
Page 52 Controls and features To disengage speed control Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. To return to a previously set speed Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph).
Page 53 Controls and features TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control. Never adjust the steering wheel when the vehicle is moving. HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter.
Page 54 Controls and features Push the control on the end of the stalk to activate washer. Push and hold for a longer wash cycle. The washer will automatically shut off after ten seconds of continuous use. Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position.
Page 55 Controls and features FLASH TO PASS Pull toward you to activate and release to deactivate. OVERDRIVE CONTROL Activating overdrive (Overdrive) is the normal drive position for the best fuel economy. The overdrive function allows automatic upshifts to second, third and fourth gear.
Page 56 Controls and features Forward storage bin (if equipped) Press the release control to open the storage compartment. The door will open slightly and can be moved to full open. The storage compartment may be used to secure sunglasses or a similar object.
Page 57 One-touch moon roof (if equipped) Press and release the rear portion of the moon roof control to open. Press and hold (as desired) the front portion of the moon roof control to close. To halt motion at any point during one-touch opening, press the control a second time.
Page 58 Controls and features Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Locate the compass module mounted at the base of the mirror. 3. Turn ignition to the ON position. 4.
Page 59 Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Start the vehicle. 2.
Page 60 Controls and features POWER WINDOWS Press and hold the rocker switches to open and close windows. Press the top portion of the rocker switch to close. Press the bottom portion of the rocker switch to open. One touch down Press AUTO completely down and release quickly.
Page 61 Controls and features Window lock The window lock feature allows only the driver to operate the power windows. WINDOW LOCK To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls. Accessory delay With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until...
Page 62 Controls and features POWER SIDE VIEW MIRRORS The ignition must be in ACC or ON position to adjust the power side view mirrors. To adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror. 2.
Page 63 Signal mirrors (if equipped) If your vehicle is equipped with signal mirrors, the word “signal” is located at the top of the right and left side view mirrors. When the turn signal is activated, the appropriate mirror will show a blinking red arrow.
Page 64 Controls and features Rear center console features (if equipped) The rear center console incorporates the following features: utility compartment cupholders POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in.
Page 65 Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle.
Page 66 Controls and features Theft indicator The theft indicator on top of the instrument panel will operate as follows: When the ignition is OFF, the theft indicator will flash briefly every 2 seconds to indicate the SecuriLock vehicle. When the ignition is turned to ON or START, the theft indicator will light for 3 seconds and then go out.
Page 67 3. Within five seconds of turning the ignition to OFF, insert the second previously programmed SecuriLock ignition from OFF to RUN (maintain ignition in RUN for at least one second but no more than 5 seconds). 4. Turn the ignition to OFF and remove the second SecuriLock from the ignition.
Page 68 Controls and features Unlocking the doors Press this control to unlock the driver door. The interior lamps and running board lamps (if equipped) will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors or the driver’s door.
Page 69 conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Page 70 Controls and features Replacing lost transmitters If a remote transmitter has been lost or you would like to purchase additional transmitters for your vehicle (up to four may be programmed), take all your vehicle’s transmitters to your dealer for reprogramming. It will be necessary for your dealer to reprogram all the remote transmitters to your vehicle while performing this service.
Page 71 Deactivating/activating the autolock feature Before following the procedure, make sure that the ignition is OFF and all vehicle doors and the liftgate window are closed. You must complete steps 1-7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds.
Page 72 Controls and features Programming your own personal entry code To program your own code: 1. Enter factory set code (keypad will illuminate when pressed). 2. Press 1/2 control within five seconds of step 1. 3. Enter your personal 5 digit code. Enter each digit within five seconds of previous one.
Page 73 Controls and features Unlocking the doors with the keyless entry system To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will also illuminate. To unlock all doors, enter the factory set code or personal code (driver door unlocks) and press the 3/4 control within five seconds.
Page 74: Seating And Safety Restraints
Seating and safety restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 75 Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Lift handle to move seat forward or backward. Pull lever up to adjust seatback. 60/40 split bench seat (if equipped) Lift the release bar to move the seat forward or backward.
Page 76 Seating and safety restraints Using the armrest (if equipped) Push the release control to move the armrest up or down. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
Page 77: Seating And Safety Restraints
Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Heated seats (if equipped) To operate the heated seats: Push control to activate. Push again to deactivate. The indicator light will illuminate when activated.
Page 78 Seating and safety restraints Push or pull the head rests to the desired position. Rear folding bench seat (if equipped) Folding down the rear seats Ensure that the headrest is in the down position and no objects such as books, purses or briefcases are on the floor in front of the second row seats before folding them down.
Page 79 Returning the seat to upright Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop. 1. Rotate the closeout panel onto the seatback and press the black control (adjacent to the green control) to lock.
Page 80 Seating and safety restraints Third row seat The third row seat is equipped with combination lap and shoulder belts in the outboard seating positions and a manual adjust tongue lap belt in the center seating position. For information on the proper operation of the safety restraints, refer to Safety Restraints in this chapter.
Page 81 Seating and safety restraints Removing the third row seat From the rear of the vehicle, with the liftgate open: 1. Disengage the lap/shoulder belt from the floor by inserting a key or small screwdriver through the hole in the boot of the detachable anchor.
Page 82 Seating and safety restraints Pull the seat release lever located on the lower right side of the seatback while pushing the seatback down into the seat cushion. The seatback will latch onto the cushion. 4. Lift the seat release bar located at the center of the seat near the floor to release the floor latches.
Page 83 When the rear of the seat is 10–13 cm (4–5 in) above the rear pins, let the seat drop. This will ensure that the seat will properly latch into the floor. 3. Locate the seat belt anchor tongue in the plastic housing on the floor. 4.
Page 84 Seating and safety restraints It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 85 The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front and rear seat passenger outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Page 86 Seating and safety restraints Grasp the shoulder portion and pull downward until the entire belt is extracted. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Page 87 Shorten and fasten the belt when not in use. Front and second row safety belt height adjustment Your vehicle has safety belt height adjustments for the driver, front passenger and second row passengers. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.
Page 88 (slide bar)(if equipped), shoulder belt height adjusters (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced.
Page 89 AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) 50 60 FUEL 0 0 0 0 0 0 DOOR AJAR BRAKE km/h P R N PULL PANEL Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
Page 90 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags...
Page 91 Seating and safety restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the...
Page 92 Seating and safety restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag is deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Page 93 Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children.
Page 94 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child.
Page 95 (passenger side front and outboard rear seating positions)(if equipped). Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps.
Page 96 Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. An air bag can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back.
Page 97 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
Page 98 Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt.
Page 99 Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. Tether anchor brackets may also be installed to the floor behind the second row seats.
Page 100 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 101 Starting 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. 4. Make sure the gearshift is in P (Park). 5. Turn the key to 4 (ON) without turning the key to 5 (START).
Page 102 Starting FUEL SERVICE ENGINE SOON FUEL DOOR Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver’s safety belt is fastened, the STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts.
Page 103 Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below.
Page 104: Starting
Starting Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Page 105 Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 106 Driving ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on and the engine is off. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced.
Page 107 Parking brake Apply the parking brake whenever the vehicle is parked. To set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released.
Page 108 Driving Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy. STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. To prevent damage to the power steering pump: Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
Page 109: Driving
Speed sensitive steering The steering in your vehicle is speed sensitive. At high speeds, steering assist will decrease to improve steering feel. At lower speeds, maneuverability will be increased. If the amount of effort required to steer your vehicle changes at a constant vehicle speed, have the power steering system checked by your dealer or a qualified service technician.
Page 110 Driving The air suspension shut-off switch is located behind an access panel underneath the passenger side instrument panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driver.
Page 111 To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire. TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift from being moved from P (Park) unless the brake pedal is depressed.
Page 112 Driving If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician. Driving with a 4–speed automatic transmission Understanding gearshift positions Pull the gearshift lever towards you and downward to move the automatic gearshift.
Page 113 N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through four. (Overdrive) can be deactivated by pressing the Transmission Control Switch (TCS) on the end of...
Page 114 Driving 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive).
Page 115 CONTROL-TRAC AUTOMATIC FOUR-WHEEL DRIVE SYSTEM (IF EQUIPPED) Your 4x4 features the heavy-duty Control-Trac system which includes a computer-operated transfer case. This unique system is interactive with the road, continually monitoring and adjusting torque delivery to the front and rear wheels to optimize vehicle control. Positions of the Control-Trac system The Control-Trac A4WD system functions in three modes:...
Page 116 Driving Using the Control-Trac system Shifting from A4WD to 4H Move the 4WD control from A4WD to 4H at any forward speed up to 88 km/h (55 mph). At temperatures below 0°C (32°F), shifts from A4WD to 4H should not be performed above 72 km/h (45 mph).
Page 117 Driving off-road with 4WD Your vehicle is specially equipped for driving on sand, snow, mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside.
Page 118 Driving Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. After driving through mud, clean off residue stuck to rotating driveshafts, halfshafts and tires.
Page 119 Driving on snow and ice A 4WD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. Avoid sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop.
Page 120 Driving GVW (Gross Vehicle Weight) : Base curb weight plus payload weight. The GVW is not a limit or a specification. GVWR (Gross Vehicle Weight Rating) : Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver’s door pillar.
Page 121 Driving The Certification Label, found on the inside pillar of the driver’s door, lists several important vehicle weight rating limitations. Before adding any additional equipment, refer to these limitations. If you are adding weight to the front of your vehicle, (potentially including weight added to the cab), the weight added should not exceed the Front Axle Reserve Capacity (FARC).
Page 122 Driving TRAILER TOWING Trailer towing with your vehicle may require the use of a trailer tow option package. Trailer towing puts additional loads on your vehicle’s engine, transmission, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing.
Page 123 Trailer towing table (with heavy duty trailer tow option) GCWR (Gross Combined Weight Rating)/trailer weights Rear Engine axle Tire size ratio 4.6L 3.31 5.4L 3.31 5.4L 3.73 4.6L 3.55 4.6L 3.55 5.4L 3.31 5.4L 3.73 5.4L 3.73 Maximum frontal area of trailer is 5.6 square meters (60 square feet) Do not exceed the maximum loads listed on the Safety Compliance Certification label.
Page 124 Driving Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. If your vehicle is not equipped with the factory heavy duty trailer tow option, auxiliary coolers are recommended for the automatic transmission system if you are planning on: traveling farther than 80 km (50 miles)
Page 125 Safety chains Always connect the trailer’s safety chains to the vehicle. To connect the trailer’s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agency gives to you.
Page 126 Driving Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer. Speed control may shut off if you are towing on long, steep grades. When towing a trailer: Use a lower gear when towing up or down steep hills. This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling.
Page 127 Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, Do not allow the static water level to rise above the bottom edge of the rear bumper and Do not allow waves to break higher than 15 cm (six inches) above the bottom edge of the rear bumper.
Page 128: Roadside Emergencies
Roadside emergencies HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. The hazard lights control is located on top of the steering column.
Page 129 The fuel pump shut-off switch is located in the passenger’s foot well, behind the kick panel. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse.
Page 130 Roadside emergencies Standard fuse amperage rating and color Fuse Mini Rating Fuses Grey Violet Pink 7.5A Brown Blue Yellow Natural Green — — — — — Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal.
Page 131: Roadside Emergencies
The fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating Roadside emergencies Description Audio Overhead Trip Computer, Electronic Automatic Temperature Control (EATC), Powertrain Control Module (PCM), Cluster Cigar Lighter, OBD-II Scan Tool Connector Autolamp Module, Remote Entry Module, Mirrors, Air Suspension Switch AC Clutch Relay, Speed Control Module, Reverse Lamp, EVO Module, Climate Mode Switch (Front Blower Relay), Daytime...
Page 132 Roadside emergencies Fuse/Relay Fuse Amp Location Rating — — — — Description Aux A/C Blower Relay, Console Blower Radio, Remote Entry Module, GEM Module Not Used Not Used Front Washer Pump Relay, Wiper Run/Park Relay, Wiper Hi/LO Relay, Windshield Wiper Motor, Rear Washer Pump Relay Not Used Stop Lamp Switch (Lamps), Turn/Hazard...
Page 133 Fuse/Relay Fuse Amp Location Rating Relay 1 — Relay 2 — Relay 3 — Relay 4 — Relay 5 — Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.
Page 134 Roadside emergencies If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Care chapter. The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating 25A * 30A* 30A* 25A* 20A* 15A* 20A* 30A* 15A*...
Page 135 Fuse/Relay Fuse Amp Location Rating 10A* — — 10A* — — 15A* 10A* 10A* — — 15A* 15A* 30A** 50A** 50A** 30A** 40A** — — 30A** 50A** 30A** 50A** 30A** 50A** 30A** — Roadside emergencies Description Rear Wipers Not Used Not Used Running Board Lamps Not Used...
Page 136 Roadside emergencies Fuse/Relay Fuse Amp Location Rating 40A** — — — — — — — — — — — — — — — — — — — — — — — — *Mini fuses **Maxi fuses Relays Relays are located in the power distribution box and should be replaced by qualified technicians.
Page 137 CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Spare tire information Your vehicle is equipped with a spare tire that may be used as a spare or a regular tire.
Page 138 Roadside emergencies Removing the spare tire 1. Open the liftgate. 2. Twist counterclockwise and remove access plug (if equipped) from guide tube located just above the rear bumper. 3. Insert the straight end of the jack handle into the guide tube. Forward motion will stop and resistance to turning will be felt when properly engaged.
Page 139 On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Refer to the instruction sheet (located behind the interior trim access panel with the jack) for detailed tire change instructions. 1.
Page 140 Roadside emergencies 7. Turn OFF the air suspension switch (if equipped). 8. Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground. When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the...
Page 141 Front (4x4) Rear To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.
Page 142 Roadside emergencies 12. Remove the jack and fully tighten the lug nuts in the order shown. 13. Put flat tire, jack and lug wrench away. Make sure the jack is fastened so it does not rattle when you drive. 14. Unblock the wheels. 15.
Page 143 Roadside emergencies Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 144 Roadside emergencies 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
Page 145 Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for a further three minutes before disconnecting the jumper cables.
Page 146 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 147 It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Page 148: Maintenance And Care
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
Page 149 Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2.
Page 150 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L V8 and 5.4L V8 engines 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Engine oil dipstick 5. Power steering fluid reservoir 6. Brake fluid reservoir 7.
Page 151: Maintenance And Care
2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5.
Page 152 Change your engine oil and filter according to the appropriate schedule listed in the Scheduled Maintenance Guide. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced.
Page 153 3. If necessary, add brake fluid until the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter. Brake fluid is toxic.
Page 154 Maintenance and care WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way.
Page 155 If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become empty. If this occurs, add engine coolant to the reservoir. For more information on engine coolant maintenance, refer to Adding engine coolant in this chapter. Automotive fluids are not interchangeable;...
Page 156 Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44–A, and use of such coolant may harm engine and cooling system components.
Page 157 level in which you drive during winter months. Never increase the engine coolant concentration above 60%. Leave a 50/50 mixture of engine coolant and water in your vehicle year-round in non-extreme climates. What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred.
Page 158 Check the power steering fluid. Refer to the Scheduled Maintenance Guide for the service interval schedules. If adding fluid is necessary, use only Ford Premium Power Steering Fluid. 1. Start the engine and let it run until it reaches normal operating...
Page 159 Maintenance and care 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and...
Page 160 Maintenance and care 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated area for normal operating temperature (H) or ambient temperature (C).
Page 161 High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used.
Page 162 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules.
Page 163 When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 164 Maintenance and care If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected.
Page 165 Maintenance and care 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the open end of the air filter housing. 4. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing.
Page 166 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.
Page 167 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Page 168 Maintenance and care SERVICING YOUR TIRES Checking the tire pressure Use an accurate tire pressure gauge. Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
Page 169 Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.), as originally offered by Ford. Do not replace your tires with “high performance” tires or larger size tires.
Page 170 Follow these guidelines when using snow tires and chains: Use only cable type chains offered by Ford as an accessory or equivalent. SAE class “S” or other conventional link type chains may contact and cause damage to the vehicle’s wheel house and/or body.
Page 171 Automotive fuels can cause serious injury or death if misused or mishandled. Observe the following guidelines when handling automotive fuel: Extinguish all smoking materials and any open flames before fueling your vehicle. Always turn off the vehicle before fueling. Automotive fuels can be harmful or fatal if swallowed.
Page 172 Maintenance and care Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. Do not use gasolines containing methanol. It can damage critical fuel systems components. Vehicles certified to meet California emission standards (indicated on the underhood Vehicle Emissions Control Information label) are designed to operate on California cleaner-burning, low-sulfur gasolines.
Page 173 It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high-quality fuel. Cleaner air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates up to 10% ethanol or 15% MTBE.
Page 174 If you must replace the fuel filler cap, replace it with a genuine Ford or Motorcraft part. The customer warranty may be void for any damage to the fuel tank or fuel system if a genuine Ford or Motorcraft fuel filler cap is not used.
Page 175 Capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty. Empty Reserve is the small amount of usable fuel remaining in the fuel tank after the fuel gauge indicates empty.
Page 176 Maintenance and care show how temperature impacts fuel economy. In general, lower temperatures give lower fuel economy. Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy.
Page 177 Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle Scheduled Maintenance Guide. Conditions Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. Carrying unnecessary weight may reduce fuel economy (approximately 2 km/h [1 mpg] is lost for every 180 kg [400 lb] of weight carried).
Page 178 Guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 179 Please consult your “Warranty Guide” for complete emission warranty information. Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the Warning Lights and Chimes section of the Instrumentation chapter.
Page 180 Maintenance and care Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance. Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’s reach.
Page 181 Maintenance and care 8. Insert the glass end of the new bulb into the headlamp assembly. When the grooves in the plastic base are aligned, push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly.
Page 182 Maintenance and care Replacing tail lamp/backup lamp bulbs The tail lamp/backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies.
Page 183 Maintenance and care High-mount brakelamp To change the high-mount brakelamp bulbs: 1. Remove the four screws from the high-mount brakelamp assembly. 2. Carefully pull the lamp assembly away from the vehicle to access the bulbs. 3. Remove the bulb socket by turning counterclockwise and a careful pull.
Page 184 Maintenance and care Using the right bulbs Function Headlamps Front park/turn lamps Front sidemarker Foglamps Turn/tail/brake lamps Liftgate lamp Backup lamp License lamp High-mount brake lamp To replace all instrument panel lights - see your dealer REPLACING THE INTERIOR BULBS Check the operation of the following interior bulbs frequently: interior overhead lamp map lamp...
Page 185 The headlamp beams are pointed substantially away from a slightly down and to the right position. CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water.
Page 186 Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up paint, repair foil or aerosol paint spray from the Ford Car Care Chemicals line. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately.
Page 187 Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage. Do not spray with cold water to avoid cracking the engine block or other engine components.
Page 188 Maintenance and care Cleaning the wiper blades and windshield If the wiper blades do not wipe properly, clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents.
Page 189 For tougher soiling concerns, Ford recommends using the leather cleaning kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label.
Page 190: Capacities And Specifications
Capacities and specifications Motorcraft part numbers Component Air filter element Battery Fuel filter Oil filter PCV valve Spark plugs* * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. ** If a spark plug is removed for inspection, it must be reinstalled in the same cylinder.
Page 191 REFILL CAPACITIES Ford Part Fluid Name Brake fluid High Performance DOT 3 Motor Vehicle Brake Fluid Engine oil Motorcraft (includes filter 5W-30 Super change) Premium Motor Fuel tank Power steering Premium Power fluid Steering Fluid Transmission Motorcraft fluid MERCON V...
Page 192 Capacities and specifications Ford Part Fluid Name Engine coolant Premium Engine Coolant Front axle Motorcraft SAE lubricant 75W90 Axle Lubricant Application Capacity 4.6L V8 engine 20.5 L with 1 row (21.7 quarts) radiator 4.6L V8 engine 21.8L with 2 row (23.0 quarts)
Page 193: Capacities And Specifications
Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter.
Page 194 Engine coolant Engine oil 4x4 front wheel bearings, 4x4 spindle needle bearings, spindle thrust bearings & front drive axle u-joint/slip spline Automatic transmission (4R100) Ford part Ford part name number Multi-Purpose DOAZ- Grease 19584-AA or F5AZ- 19G209-AA Penetrating and...
Page 195 Use of any fluid other than the recommended fluid may cause transmission damage. Add 118 ml (4 oz.) of EST-M2C118–A (friction modifier Part No. C8AZ-19B546–A) for complete refill of Ford Traction-Lok rear axles. Capacities and specifications Ford part...
Page 196 Capacities and specifications ENGINE DATA Engine Cubic inches Horsepower Torque Recommended fuel Firing order Spark plug gap Ignition system Compression ratio VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Vehicle width *width including mirrors *with optional running boards (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear...
Page 197 Capacities and specifications...
Page 198: Certification Label
Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block and transmission. MFD. BY FORD MOTOR CO. IN U.S.A. DATE: XXXXX GVWR:XXXXX LB/ XXXXX KG FGAWR: XXXXXX/XXXXXXX RGAWR: XXXXXXX/XXXXXXX...
Page 199: Customer Assistance
GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: 24–hours, seven days a week for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.) of three years or 60,000 km (36,000 miles),...
Page 200 5,200 participating Ford, Lincoln-Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Please contact your dealer for further information. Since this information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options.
Page 201: Customer Assistance
Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to return to it for that service, but you may also take your vehicle to another Ford Motor Company dealership authorized for warranty repairs.
Page 202 Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Page 203 Your application is reviewed and, if it is determined to be eligible, you will receive an acknowledgment indicating: the file number assigned to your application the toll-free phone number of the DSB’s independent administrator Your dealership and a Ford Motor Company representative are asked to submit statements at this time. Customer assistance...
Page 204 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to...
Page 205 The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by using improper fuel.
Page 206 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY...
Page 207 In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigid engineering and safety specifications. Ford accessories are warranted for up to 12 months or 20,000 km (12,000 miles)
Page 208 Customer assistance Travel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adaptors Fog lights Framed luggage covers Heavy-duty battery Neutral towing transfer case kit (Explorer 4.0L only) Off road lights Pickup box rails Removable luggage rack Removable luggage rack adapters Retractable bed hooks and loops Running boards...
Page 209 Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers (full and mini) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rallye bars Rear air deflectors Rear decklid spoilers Side window air deflectors Spare tire lock Step bumpers Step/sill plates...
Page 210 (Citizens band [CB] transceivers, garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your vehicle’s operation.) Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment. ORDERING ADDITIONAL OWNER’S LITERATURE...
Page 211: Reporting Safety Defects
However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.
Page 212 ...155 refill capacities ...156 Customer Assistance Ford accessories for your vehicle ...206,207,208 Ford Extended Service Plan .200 Getting assistance outside the U.S. and Canada ...205 Getting roadside assistance ...199 Getting the service you need ...201 Ordering additional owner’s literature ...210...
Page 213 Engine oil checking and adding ...152 dipstick ...150 specifications ...150,152 Exhaust fumes ...103 Fail safe cooling ...157 Floor mats ...64 Four-Wheel Drive vehicles ..10,114 control trac ...115 description ...115 driving off road ...117 electronic shift ...19,116,117 indicator light ...10 Fuel choosing the right fuel ...172 comparisons with EPA fuel economy estimates ...177...
Page 214 Index fuel reset ...11 low fuel ...6 low washer fluid ...10 safety belt ...8 service engine soon ...6,7 turn signal indicator ...8 Locks childproof ...61 doors ...61 Lumbar support, seats ...74,75 Message center ...14,57 english/metric button ...15 menu button ...15 Mirrors fold away ...63 heated ...62,63...
Page 215: Index
Ventilating your vehicle ...104 Warning chimes ...11 Washer fluid ...154 Water, Driving through ...119 Windows ...59,60,61 rear wiper/washer ...54 Windshield washer fluid and wipers checking and cleaning ...165 operation ...53 replacing wiper blades ...166 Index...
Page 216: Filling Station Information
(4x2) Automatic transmission fluid capacity-4R100 (4x4) Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. Ensure correct automatic transmission fluid is used for a specific application.

This manual is also suitable for:

Expedition 1999

Ford 1998 Expedition Owner's Manual

Quick Links

Related Manuals for Ford 1998 Expedition

Summary of Contents for Ford 1998 Expedition

This manual is also suitable for:

Table of Contents