Page 2 The 2003 Buick Rendezvous Owner Manual Seats and Restraint Systems Front Seats Rear Seats Safety Belts Child Restraints Air Bag Systems Restraint System Check Features and Controls ... Keys Doors and Locks Windows Theft-Deterrent Systems Starting and Operating Your Vehicle...
Page 3 For vehicles first sold in Canada, substitute the name “General Motors of Canada Limited’’ for Buick Motor Division whenever it appears in this manual. Please keep this manual in your vehicle, so it will be there if you ever need it when you’re on the road.
Page 4 Index A good place to look for what you need is the Index in back of the manual. It’s an alphabetical list of what’s in the manual, and the page number where you’ll find it. Safety Warnings and Symbols You will find a number of safety cautions in this book. We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignore the warning.
Page 5 Vehicle Damage Warnings Also, in this book you will find these notices: Notice: These mean there is something that could damage your vehicle. A notice will tell you about something that can damage your vehicle. Many times, this damage would not be covered by your warranty, and it could be costly.
Page 6 These are some examples vehicle symbols you may LATCH BOTH LAP AND CAUTION SHOULDER BELTS TO POSSIBLE PROTECT OCCUPANT INJURY DO NOT TWIST SAFETY BELT WHEN ATTACHING PROTECT SHIELDING CAUSTIC MOVE SEAT \ ! $ % BAlTERY FULLY \CID COULD REARWARD* CAUSE SECURE...
Page 8: Table Of Contents
Front Seats ... Manual Passenger Seat ... 1. 3 Four-Way Manual Driver Seat ... Six-Way Power Seats Manual Lumbar ... Heated Seats Reclining Seatbacks ... Head Restraints ... Rear Seats ... Rear Seat Operation ... Split Bench Seats ... Captain Chairs ... Stowable Seat ...
Page 9 Section 1 Systems ... Air Bag Where Are the Air Bags? ... When Should an Air Bag Inflate? . What Makes an Air Bag Inflate? .. How Does an Air Bag Restrain? ... What Will You See After Air Bag Inflates? Servicing Your Air Bag-Equipped Vehicle Seats and Restraint Systems 1.74...
Page 10: Front Seats
Front Seats Manual Passenger Seat Pull up on the lever, located on the front of the seat, to unlock and move the seat. Slide the seat to where you want it and release the lever. To make sure the seat is locked into place, try to move seat back ana iorin wiiil p u r...
Page 11 To raise the seat, pull up on the lever located on the front right side the seat. To lower the seat, push the lever down. Adjust the seat and release the lever. 1 -4 lose You can adjust a manual driver’s seat while the vehicle is moving.
Page 12: Six-Way Power Seats
Six-Way Power Seats Your vehicle may have this feature. If it does, the six-way power seat control is located on the outboard sides of the driver’s and front passenger’s seats. Move the front of the control up or down to adjust the front portion of the cushion up or down.
Page 13: Heated Seats
Heated Seats Your vehicle may have heated seats. If it does, the heated seat switches are located in the instrument panel switchbank. This feature will quickly heat the lower cushions and lower back of the driver’s and front passenger’s seat. The left switch is for the driver’s seat and the right switch is for the front passenger’s seat.
Page 14 But don’t have a seatback reclined if your vehicle is moving. Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re reclined like this. The shoulder belt can’t do its job because won’t be against your body.
Page 15: Head Restraints
Head Restraints Adjust your head restraint so that the top is closest to the top of your head. This position reduces the chance of a neck injury in a crash. The front seat head restraints are adjustable. Slide the head restraint up or down to adjust On some models, the head restraints tilt forward and rearward also.
Page 16: Rear Seats
Rear Seats Rear Seat Operation The rear seats in your vehicle have seat operating features to adjust, fold, remove and reinstall the seats. By using the seat operating procedures, in the correct order, you can easily remove the seats from your vehicle.
Page 17 To recline the seatback on up-level split bench seats, push forward on the recliner lever located on the outboard side of the seatback. Up-Level Move the seatback to the desired position. It is easier to raise or lower the seatback if you lean forward and take the weight off the seatback.
Page 18 Base-Level 4. For base-level split bench seats, pull the lever at the base of the seat on the outboard side to release the rear latches from the floor pins and flip the seat forward. L - - - L . - I - - - I ! I - e r r + - Up-level splli...
Page 19 Replacing the Split Bench Seat If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure locked. A seat that isn’t locked into place properly can move around in a collision or sudden stop.
Page 20 2. Make sure that the bench seat is angled so that the front hooks clear the floor pins. If the front legs are not attached correctly, the rear legs will not attach to the rear set of floor pins. 1. Squeeze the angled latch release bar toward the straight crossbar while placing the front hooks of onto the bench seat...
Page 21: Captain Chairs
3. Firmly push the rear hooks onto the rear floor pins by pushing down on the rear of the seat. 4. Try to raise the seat to check that it is locked down. 5. Lift the seatback recliner lever and raise the seatback until it locks upright.
Page 22 To recline the seatback, lift up on the recliner lever located on the outboard side of the seatback. Use the recliner lever to move the seatback to the desired position. It is easier to raise or lower the seatback if you lean forward and take the weight off the seatback.
Page 23 4. The seat can then be lifted off the front floor pins. 5. Remove the seat rocking it slightly toward the rear of the vehicle and then pulling it out. Repeat these steps for the other captain’s chair. 1-16 Replacing the Captain’s Chairs If the seatback isn’t locked, it forward in a sudden stop or crash.
Page 24 A safety belt that improperly routed, not properly attached, or twisted won’t provide the protection needed in a crash. The person wearing the belt could be seriously injured. After installing the seat, always check to be sure that the safety belts are properly routed and attached, and are not twisted.
Page 25: Stowable Seat
2. Push the rear of the seat down to lock the rear latches onto the rear set of floor pins. Push and pull on the seat to check that it is properly attached. 1-18 Stowable Seat The stowable seat a two passenger bench seat and comes with the rear convenience center.
Page 26 To fold the seatback down, pull up on the lever located on the back of the seat. Push down on the seatback until into place. Push and pull on the seatback to make sure that it is locked into place. To raise the seatback, do one of the following: From the rear of the vehicle, pull up on the lever to release the seatback.
Page 27 Rep’-cir the Sto---able S-7t If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure locked. A seat that isn’t locked into place properly can move around in a collision or sudden stop.
Page 28 The stowable seat has seat position labels, located on the back of the seat, showing where the seat must go. The seat must be placed in the proper location for the legs to attach correctly. Make sure that the seatback is folded forward before beginning this procedure.
Page 29: Safety Belts: They Are For Everyone
Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety also belts properly. It tells you some things you should not do with safety belts. Don’t let anyone ride where he or she can’t wear a safety belt properly.
Page 30 Your vehicle has a light that comes on as a reminder to buckle Safety Belt Reminder Light on In most states and in all Canadian provinces, the law says to wear safety belts. Here’s why: They work. After more than 30 years of safety belts in vehicles, the facts are clear.
Page 33: Questions And Answers About Safety Belts
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That’s why safety belts make such good sense. 1-26 Questions and Answers About Safety Belts...
Page 34: How To Wear Safety Belts Properly
If I’m a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you’re in an accident even one that isn’t your fault your passengers can be hurt.
Page 35 Driver Position This part describes the driver’s restraint system. Lap-Shoulder Belt The driver has a lap-shoulder belt. Here’s how to wear properly. 1. Close and lock the door. 2. Adjust the seat so you can sit up straight. To see how, see “Seats”...
Page 36 5. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder belt. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones.
Page 37 Shoulder Belt Height Adjuster Before you begin to drive, move the shoulder belt adjuster to the height that is right for you. 1-30 To move it down, push down on the button and move the height adjuster to the desired position. You can move the adjuster up just by pushing up on the shoulder belt guide.
Page 38 What's wrong with this? You can be seriously hut f y c ulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit against your body. 1-31...
Page 39 What’s wrong with this? The belt is buckled in the wrong place. You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 40 What’s wrong with this? You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. a crash, you can slide under the belt. The belt force would then be applied at the abdomen, not at the pelvic bones, and that could cause serious or fatal injuries.
Page 41 What’s wrong with this? The shoulder belt is worn under the arm. be worn over the shoulder at all times. You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 42 What’s wrong with this? is twisted across the body. The belt You can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to fix it.
Page 43 To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door it, you can damage both the belt and your vehicle.
Page 44: Right Front Passenger Position
The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Page 45 Rear Seat Outside Passenger Positions Rear Seat Passengers It’s very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who aren’t safety belted can be thrown out of the vehicle in a crash.
Page 46 Lap-Shoulder Belt The positions next to the windows have lap-shoulder belts. Here’s how to wear one properly. 1. Pick up the latch plate and pull the belt across you. Don’t let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly.
Page 47 3. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder part. 1-40 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the pelvic bones.
Page 48 The safety belt locks if there’s a sudden stop or a crash, or if you pull the belt very quickly out of the retractor. Each position next to the windows in the second row has a shoulder belt height adjuster. Move the shoulder belt adjuster to the height that is right for you.
Page 49: Center Rear Passenger Position
Center Rear Passenger Position Lap-Shoulder Belt If your vehicle has a bench seat, someone can sit in the center position. When you sit in the center seating position, you have a lap safety belt, which has no retractor. You have a shoulder belt, which has a retractor. In order to have the protection of the shoulder belt, you must first connect it to the lap belt.
Page 50 3. To make the lap belt longer, tilt the latch plate and 2. Insert the metal knob on the shoulder belt into the pull it along the belt. keyhole on the lap belt buckle as shown. Be sure to slide the shoulder belt part into the keyhole until it locks into place.
Page 51: Rear Safety Belt Comfort Guides For Children And Small Adults
To make the belt shorter, pull its free end as shown until the belt is snug 4. Buckle, position and release the lap-shoulder belt the same way as the other lap-shoulder belts. If the belt isn’t long enough, see Safety Belt Extender on page 1-48.
Page 52 Second Row Outside Positions 2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide. For second row outside positions do the following: 1. Remove the guide from its storage clip located on the sidewall next to the outer side of each outslcle passenger position.
Page 53 3. Be sure that the belt is not twisted and it lies flat. The guide must be on top of the belt. 1 -46 4. Buckle, position and release the safety belt as described in Rear Seat Passengers on page Make sure that the shoulder belt crosses the shoulder.
Page 55: Safety Belt Extender
3. Be sure that the belt is not twisted and it lies flat. The guide must be on top of the belt. 4. Buckle, position and release the safety belt as described in Center Rear Passenger Position on page 7-42. Make sure that the shoulder belt crosses the shoulder.
Page 56: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle's safety belts. What is the proper way to wear safety belts? If possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide.
Page 57 1-50 Never do this. Here two children are wearing the same belt. The belt can’t properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck?
Page 58 Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt.
Page 59: Infants And Young Children
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 60 it. For example, in a crash at only 25 mph (40 km/h), a 12-lb. (5.5 kg) baby will suddenly become a 240-lb. (110 kg) force on a person’s arms. A baby should be secured in an appropriate restraint. Children who are up against, or very close to, any air bag when it inflates can be seriously injured or killed.
Page 61 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 62: Child Restraint Systems
The body structure of a young child is quite unlike that of an adult or older child, for whom the safely belts are designed. A young child's hip bones are still so small that the vehicle's regular safety belt may not remain low on the hip bones, as should.
Page 63 A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. 1 -56 A forward-facing child seat (C-E) provides restraint for the child's body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields.
Page 64 A booster seat (F-G) is a child restraint designed to improve the fit of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and high-bsck ,hcc+er rezts hal~e cnmn - v . A booster seat can also help a child to see out the window.
Page 65: Where To Put The Restraint
When choosing a child restraint, be sure the child restraint is designed to be used in a vehicle. If it is, it will have a label saying that it meets federal motor vehicle safety standards. Then follow the instructions for the restraint. You may find these instructions on the restraint itself or in a booklet, or both.
Page 66: Top Strap
Top Strap Some child restraints have a top strap, or “top tether.” can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle. Some top strap-equipped child restraints are designed for use with or without the top strap being anchored.
Page 67: Top Strap Anchor Location
Anchor the top strap to one of the following anchor points. Be sure to use an anchor point located on the same side of the vehicle as the seating position where the child restraint will be placed. If you have an adjustable head restraint, route the top strap under it.
Page 68 Second Row Outside Positions Bench Seat Second Row Center Position Bench Seat without Third Row Seat 1-61...
Page 69 Your vehicle has top strap anchors already installed for the rear seating positions. An anchor bar for a top strap is located at the rear of the seat cushion for each second row outboard seating position and the anchor bar for the center position for the bench seat on the floor behind the second row seats.
Page 70 Second Row Center Position Bench Seat with Third Row Seat Folded Down If the vehicle has a third row seat and the seatback is folded, there is anchor on the back for the second row center position bench seat. Third Row Passenger’s Side Outside Position There is also a top strap anchor for third row passenger’s side outside position.
Page 71: Lower Anchorages And Top Tethers For Children (Latch System)
Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle has the LATCH system. You’ll find anchors (A) in the second row outside passenger positions. To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system will have latches between the seatback and cushion.
Page 72 With this system, use the LATCH system instead of the vehicle’s safety belts to secure a child restraint. If a LATCH-type child restraint isn’t attached to its anchorage points, the restraint won’t be able to protect a child sitting there. In a crash, the child could be seriously injured or killed.
Page 73: Securing A Child Restraint Designed
Securing a Child Restraint Designed for the LATCH System 1. Find the anchors for the seating position you want to use, where the bottom of the seatback meets the back of the seat cushion. 2. Put the child restraint on the seat. Attach the anchor points on the child restraint anchors in the vehicle.
Page 74 You'll be using the lap-shoulder belt. See Top Strap page 1-59 if the child restraint has one. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say. 1.
Page 75 3. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 1-68 To tighten the belt, pull up on the shoulder belt while you push down on the child restraint. If you're using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 76: Securing A Child Restraint In A
Securing a Child Restraint in Center Rear Seat Position The center rear seating position has a lap-shoulder belt. To secure a child restraint in this position, you'll use only the lap part of the belt. Disconnect the shoulder part of the belt and store it before securing child restraint. See Center Rear Passenger Position on page 1-42.
Page 77 1 -70 4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 5. To tighten the belt, pull its free end while you push down on the child restraint.
Page 78: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Right Front Seat Position Your vehicle has a front passenger air bag. Never put a rear facing child restraint in this seat. Here’s why: A child in a rear-facing h i l d restraint can be seriously injured or killed if the front passenger’s air bag inflates.
Page 79 If the shoulder belt goes in front of the child’s face 4. Buckle the belt. Make sure the release button is or neck, put it behind the child restraint. positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 1-72...
Page 80 To tighten the belt, pull up on the shoulder belt while you push down on the child restraint. You may find it helpful to use your knee to push down on the child restraint as you tighten the belt. Push and pull the child restraint in different directions to be sure it is secure.
Page 81: Air Bag Systems
Air Bag Systems This part explains the frontal and side impact air bag systems. Your vehicle has air bags a frontal air bag for the driver and another frontal air bag passenger. Your vehicle may also have a side impact air bag.
Page 82 Here are the most important things to know about the air bag systems: You can be severely injured if you aren’t wearing your safety belt you have air bags. Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from Air bags are designed to work...
Page 83 Both frontal and side impact air bags inflate with great force, faster than the blink of an eye. If you’re too close to an inflating air bag, as you would be if you were leaning forward, it could seriously injure you. Safety belts help keep you in position for air bag inflation before and during a crash.
Page 84: Where Are The Air Bags
There is a air bag readiness light on the instrument panel cluster, which shows the air bag symbol. The system checks the air bag electrical system for malfunctions. The light tells you if there is an electrical problem. See Air Bag Readiness Light on page for more information.
Page 85 The right front passenger’s frontal air bag is in the If your vehicle has one, the driver’s side impact air bag instrument panel on the passenger’s side. is in the side of the driver’s seatback closest to the door. 1-78...
Page 86 If your vehicle has one, the right front passenger’s side impact air bag is in the side of the passenger’s seatback closest to the door. If something is between an occupant and an air bag, the bag might not inflate properly or it might force the object into that person causing severe injury or even death.
Page 87: When Should An Air Bag Inflate
When Should an Air Bag Inflate? The driver’s and right front passenger’s frontal air bags are designed to inflate in moderate to severe frontal or near-frontal crashes. But they are designed to inflate only if the impact speed is above the system’s designed “threshold level.”...
Page 88: What Makes An Air Bag Inflate
What Makes an Air Bag Inflate? In an impact of sufficient severity, the air bag sensing system detects that the vehicle is in a crash. For both frontal and side impact air bags, the sensing system triggers a release of gas from the inflator, which inflates the air bag.
Page 89: What Will You See After An Air Bag Inflates
What Will You See After an Air Bag Inflates? After the air bag inflates, it quickly deflates, so quickly that some people may not even realize the air bag inflated. Some components of the air bag module will be hot for a short time. These components include the steering wheel hub for the driver’s frontal air bag and the instrument panel for the right front passenger’s frontal air bag.
Page 90: Servicing Your Air Bag-Equipped Vehicle
Your vehicle is equipped with an electronic frontal sensor, which helps the sensing system distinguish between a moderate frontal impact and a more severe frontal impact. Your vehicle is also equipped with a crash sensing and diagnostic module, which records information about the frontal air bag system. The module records information about the readiness of the system, when the system commands air bag inflation and driver’s safety belt usage at deployment.
Page 91: Restraint System Check
Restraint System Check Checking Your Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Page 92 If the LATCH system was being used during a more severe crash, you may need new LATCH system parts. If you ever see a label on the driver’s or right front passenger’s safety belt that says to replace the belt, be sure to do so.
Page 94: Features And Controls
Section 2 Keys Remote Keyless Entry System Remote Keyless Entry System Doors and Locks Door Locks Power Door Locks Delayed Locking Programmable Automatic Door Locks Rear Door Security Locks Lockout Protection Leaving Your Vehicle Liftgate ... 2.11 Windows ... Power Windows Sun Visors Theft-Deterrent Systems Content Theft-Deterrent ...
Page 95 Section Onstar@ ... Onstar@ System HomeLink@ Transmitter ... Programming the HomeLink@ Transmitter ... 2.38 Storage Areas Glove Box ... Cupholder(s) ... Cell Phone Storage Area Overhead Console ... Floor Console Storage Area Front Armrest Storage Area Roof Rack System ... Rear Storage Area Features and Controls Convenience Net ...
Page 96: Keys
Keys Leaving children in a vehicle with the i,..ition key is dangerous for many reasons. A child or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. Don’t leave the keys in a vehicle with children.
Page 97: Remote Keyless Entry System
You may even have to damage your vehicle to get in. So be sure you have spare keys. If you ever do get locked out of your vehicle, call Buick Roadside Assistance. See Roadside Assistance Program page 7-5 for more information.
Page 98: Remote Keyless Entry System Operation
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment.
Page 99 The UNLOCK button on the remote keyless entry transmitter will disarm the content theft-deterrent system. See Content Theft-Deterrent on page 2- 16 for more information. If you would like to program the way the headlamps and parking lamps operate with remote unlock confirmation, see Vehicle Personalization on page 2-50.
Page 100 Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about three years. KEY FOB BATTERY United States You can tell the battery is weak if the KEY FOB BATTERY LOW message appears in the message center.
Page 101: Doors And Locks
Doors and Locks Door Locks Unlocked doors can be dangerous. Passengers especially children easily open the doors and fall out of a moving vehicle. When a door is locked, the handle won’t open it. You increase the chance of being thrown out of the vehicle in a crash if the doors aren’t locked.
Page 102: Power Door Locks
Power Door Locks The power door lock switch is located on the driver's and front passenger's doors next to the door handle. Press the front of the switch to lock all doors, or press the back of the switch to unlock all doors. The rear doors do not have power door lock switches.
Page 103: Rear Door Security Locks
To program the automatic door lock feature, see Vehicle Personalization on page 2-50 If your vehicle is equipped with the Driver Information Center (DIC), see Vehicle Personalization on page 3-59. Rear Door Security Locks Your vehicle is equipped with rear door security locks that help prevent passengers from opening the rear doors on your vehicle from the inside.
Page 104: Lockout Protection
Lockout Protection The lockout protection feature makes it difficult for you to lock your keys in your vehicle. If any door is open while the key is in the ignition, pressing the front of a power door lock switch will lock all doors, then unlock the driver’s door.
Page 105 Liftgate Release Liftgate Handle 2-1 2 Your vehicle may have either a liftgate release button, located in the instrument panel switchbank, or a release button located on the inner side of the liftgate handle. Instrument Panel Switchbank To open the liftgate, the transaxle must be in PARK (P) and all of the doors must be unlocked.
Page 106: Windows
Windows Leaving children in a vehicle with the windows closed is dangerous. A child can be overcome by the extreme heat and can suffer permanent injuries or even death from heat stroke. Never leave a child alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 107: Power Windows
Power Windows Switches on the driver’s door armrest control each of the windows when the ignition is in ON, ACCESSORY, or when retained accessory power is active. See “Retained Accessory Power (RAP)” under Positions on page 2-20 for more information. In addition, each passenger’s door has a window switch.
Page 108: Sun Visors
Window Lock Out The driver’s window controls also include a lock-out switch. Press the right side of the WDO LOCK switch to stop rear passengers from lowering their window. The driver can still control all of the windows with the lock on.
Page 109: Theft-Deterrent Systems
Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Content Theft-Deterrent Your vehicle may have a theft-deterrent alarm system. A light located on top of your instrument panel (near the center of...
Page 110: Pass-Key@ Ill
Arming with the Power Lock Switch Your alarm system will arm when you use either power door lock switch to lock the doors while any door or the liftgate is open and the key is removed from the ignition. The security light will start flashing to let you know the system is armed.
Page 111: Pass-Key@ Ill Operation
PASS-Key@ 111 Operation Your vehicle is equipped with the PASS-Key@ Ill (Personalized Automotive Security System) theft-deterrent system. PASS-Key@ Ill is a passive theft deterrent system. This means you don’t have to do anything different to arm or disarm the system. It works when you insert or remove the key from the ignition.
Page 112 Canadian Owners: If you lose or damage your keys, only a GM dealer can service PASS-Key@ Ill to have new keys made. To program additional keys you will need two current driver’s keys (black in color). You must add a step to the following procedure. After Step 3 repeat Steps 1 through 3 with the second current driver’s key.
Page 113: Starting And Operating Your Vehicle
Starting and Operating Your Vehicle New Vehicle Break-In Notice; Your vehicle doesn’t need an elaborate “break-in.” But it will perform better in the long run if you follow these guidelines: If you have all-wheel drive, keep your speed at 55 mph (88 km/h) or less for the first 500 miles (805 km).
Page 114: Starting Your Engine
Notice: If your key seems stuck in OFF and you can’t turn it, be sure you are using the correct key; if so, is it all the way in? If is, then turn the steering wheel left and right while you turn the key hard.
Page 115: Engine Coolant Heater
Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter.
Page 116: Automatic Transaxle Operation
Plugging the cord into an unground,, could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured. Plug the cord into a properly grounded three-prong 11 0-volt AC outlet. If the cord won’t reach, use a heavy-duty three-prong extension cord rated for at least 15 amps.
Page 117 If you cannot shift out of PARK (P), ease pressure on the shift lever push the shift lever all the way into PARK (P) as you maintain brake application. Then move the shift lever into the gear you wish. See Shifting Out of Park (P) on page for more information.
Page 118 Notice: Damage to your transaxle caused by shifting into a drive gear with the engine racing isn't covered by your warranty. AUTOMATIC OVERDRIVE (D): This position is for normal driving. If you need more power for passing, and you're: Going less than 35 mph (55 km/h), push your accelerator pedal about halfway down.
Page 119: Parking Brake
SECOND This position gives you more power, but ( 2 ) : lower fuel economy. You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use your brakes off and on.
Page 120: Shifting Into Park (P)
If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 3-40. To release the parking brake, hold the regular brake pedal down with your right foot while you push down on the parking brake pedal with your left foot.
Page 121 2. Move the shift lever into PARK (P) like this: Pull the lever toward you. 2-28 Move the lever up as far as it will go. 3. Turn the ignition key to LOCK. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P).
Page 122 Leaving Your Vehicle With the Engine Running It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire.
Page 123: Shiftng Out Of Park (P)
Shiftng Out of Park (P) Your vehicle has an automatic transaxle shift lock control system. You have to fully apply your regular brakes before you can shift from PARK (P), when the ignition is in ON. As you step on the brake pedal, while in PARK (P), you may hear a click from the solenoid of the system.
Page 124: Engine Exhaust
Engine Exhaust Engine exhaust can kill. contains the gas carbon monoxide (CO), which you can’t see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: Your exhaust system sounds strange or different. .” .,-h;-l- rusty underneath.
Page 125: Running Your Engine While You Are Parked
Running Your Engine While You Are Parked It’s better not to park with the engine running. But if you ever have to, 1 e are some things to know. Idling the engine with the clin system off could allow dangerous exhaust into your vehicle.
Page 126: Mirrors
Mirrors Manual Rearview Mirror To reduce glare from headlamps behind you, pull the lever toward you (to the night position). To return the mirror to the day position, push the lever away from you. Automatic Dimming Rearview Mirror Your vehicle may have an automatic dimming rearview mirror.
Page 127: Outside Curb View Assist Mirror
Outside Curb View Assist Mirror If your vehicle has this feature, the passenger’s outside rearview mirror will tilt towards the curb when the vehicle shifted into REVERSE (R) and return to its previous position when the vehicle is shifted out of REVERSE (R).
Page 128: Onstar@ System
Onstar* System Onstar@ uses global positioning system (GPS) satellite technology, wireless communications, and state of the art call centers to provide you with a wide range of safety, security, information and convenience services. An Onstar@ subscription plan is included in the price of your vehicle.
Page 129 Onstar@ Personal Calling With Onstar@ Personal Calling, you have a safer way to stay connected while driving. It’s a hands-free wireless phone that’s integrated into your vehicle. You can place calls nationwide using voice-activated dialing with no contracts, no roaming charges and no access fees. To find out more about Onstar@ Personal Calling, refer to the Onstar@ owner’s guide in your vehicle’s glove box, or call Onstar@ at 1-888-4-ONSTAR...
Page 130: Homelink@ Transmitter
HomeLink@ Transmitter HomeLin!P, CGmbined unilfersa! transmitter and receiver, provides a convenient way to replace up to three hand-held transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems and home lighting. Additional HomeLink@ information can be found on the internet at www.homelink.com or by calling 1-800-355-351 5.
Page 131: Programming The Homelink@ Transmitter
Programming the HomeLink@ Transmitter Do not use the HomeLink@ Transmitter with any garage door opener that does not have the “stop and reverse” feature. This includes any garage door opener model manufactured before April 1, 1982. Keep the original transmitter for use in other vehicles as well as for future HomeLink@ programming.
Page 132 To program the remaining two HomeLink@ buttons, begin with Step 2 under “Programming HomeLink@.” Do not repeat Step 1 as this will erase all of the programmed channels. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Steps 6 through 8 following to complete the programming of a rolling-code equipped device (most commonly a garage door opener).
Page 133 Using HomeLink@ Press and hold the appropriate HomeLink@ button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing HomeLink@ Buttons To erase programming from the three buttons do the following: 1.
Page 134: Storage Areas
Storage Areas Glove Box If the glove box has a lock, put your key into the lock and turn the key counterclockwise. To open the glovebox, pull the latch release. The glove box door has a detent to prevent the door To close the glove box, the door must be pushed up past the detent.
Page 135: Floor Console Storage Area
Sunglasses Storage Compartment To open the sunglasses storage compartment in the overhead console, press the release button. Then pull the compartment down to the full open position. Floor Console Storage Area The floor console storage contains two cupholders, an ashtray and a cellular phone storage compartment with a cigarette lighter/accessory power outlet.
Page 136 If you have the luggage carrier, you can load things on top of your vehicle. If you do load things on the top of your vehicle, you must load them on the luggage carrier crossrails. Notice: Damage may be caused to the roof of your : + 1 - l - - a c l - - - # - ! - I -...
Page 137 To prevent damage or loss of cargo as you’re driving, check now and then to make sure the luggage carrier and cargo are still securely fastened. Loading things onto the luggage carrier can interfere with the performance of your XMTM Satellite Radio System.
Page 138: Convenience Net
To adjust the crossrails, lift the release levers on each side to unlock them. Slide the crossrails forward or backward, as needed, to accommodate loads of various sizes. After repositioning the crossrails, engage the release lever. This will lock the crossrails in place. Notice;...
Page 139 R-Br C-rvenience Cent-r any removable convenience item isn’t secured properly, it can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to secure any such item properly. Your vehicle may have a rear convenience center. The rear convenience center can be used and store items in your vehicle.
Page 140 Replacing the Extended Rear Convenience Center 1. Make sure that all items have been removed from the rear of the vehicle. 2. Remove the carpeted mat from the vehicle..3. Lift the forward bin into the back of the vehicle. Place the mounting brackets onto the forward mounting bolts on the floor of the vehicle.
Page 141 Removing the Rear Convenience Center on Vehicles with the Third Row Stowable Seat 1. Make sure that all items have been removed from the top and the inside of the rear convenience center. 2. Lift the handle(s) on the top of the lid to open the storage bin.
Page 142: Sunroof
Sunroof If your vehicle has a sunroof, the switch is located between the sun visors. The sunroof switch will only work when the ignition is on or when the ignition is off and retained accessory power is active. See “Retained Accessory Power” under lgnition Positions on page 2-20 for more information.
Page 143: Vehicle Personalization
Vehicle Personalization Some of your vehicle’s features can be reset or customized according to your preference. The features you can program depend on the options that came with your vehicle. If your vehicle has a DIC, see DIC Vehicle Personalization on page 3-59 to customize your features.
Page 144: Headlamp Exit Delay
Headlamp Exit Delay This feature allows you to customize the headlamps and parking lamps. Programmable Modes Mode 1: Off (The headlamps and parking lamps will turn off at the same time that the ignition is turned to OFF.) Mode 2: 15-Second Activation (The headlamps and parking lamps will stay on for 15 seconds when the ignition is turned to OFF.) Mode...
Page 145: Automatic Door Locwunlock
Automatic Door LocWUnlock This feature allows you to lock and unlock your doors automatically. Programmable Modes Mode Automatic Door Locking Only Shift out of PARK (P) with the ignition on and the driver’s door closed; all doors will lock automatically. The automatic door unlock feature is turned off.
Page 146: Delayed Locking
3. Count the number of chimes you hear. The number of chimes indicates the vehicle's current programmed mode. If you do not wish to change the current mode, you can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
Page 147: Remote Driver Unlock Control
Remote Driver Unlock Control This feature allows you to customize the UNLOCK button on the remote keyless entry transmitter. Programmable Modes Your vehicle can be programmed to one of the following modes. Mode 1: Remote All Doors Unlock (When you press UNLOCK on your remote keyless entry transmitter, all doors will unlock.) Mode 2: Remote Driver’s Door Unlock Only (When you...
Page 148: Remote Lock And Unlock Confirmation
Remote Lock and Unlock Confirmation This feature allows you to customize the feedback received when locking or unlocking your vehicle with the remote keyless entry transmitter. Programmable Modes Mode 1: Both Features Off (Remote lock and unlock confirmation are disabled.) Mode 2: Exterior Lamps Flash Only When you use the remote keyless entry transmitter to lock your vehicle, your headlamps and parking...
Page 149: Exiting Programming Mode
3. Count the number of chimes you hear. The number of chimes indicates the vehicle’s current programmed mode. If you do not wish to change the current mode, you can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
Page 150: Memory Seat
Memory Seat If your vehicle has this feature, the controls are located on the driver’s door Dane1 and are used to program and recall the driver’s seat position and outside rearview mirror position. Adjust the driver’s seat and the outside rearview mirrors to the position you would like for driving.
Page 151 NOTES 2-58...
Page 152: Instrument Panel
Section Instrument Panel Overview ... 3. 4 Hazard Warning Flashers Other Warning Devices Horn Tilt Wheel Turn SignaVMultifunction Lever Exterior Lamps Interior Lamps Instrument Panel Switchbank Head-Up Display (HUD) Ultrasonic Rear Parking Assist (URPA) Accessory Power Outlets Ashtrays and Cigarette Lighter Climate Controls Climate Control System Dual Climate Control System...
Page 153 Section 3 All-Wheel Drive Disable Warning Message Low Washer Fluid Warning Message ... 3-52 Low Fuel Warning Message Low Brake Fluid Warning Message Service Vehicle Soon Message Program Mode Message ... Remote Keyless Entry Transmitter Battery Warning Message Park Lamp Warning Message ... Highbeam Out Warning Message ...
Page 154 S310N €-€...
Page 155: Instrument Panel Overview
Instrument Panel Overview...
Page 156 The main components of the instrument panel are the following: A. Exterior/lnterior Lamps Control Turn SignaVMultifunction Lever C. Hazard Warning Flasher Switch D. instrument Panel Cluster E. Shift Lever F. Instrument Panel Outlets G. Audio System H. Audio Steering Wheel Controls I.
Page 157: Hazard Warning Flashers
Hazard Warning Flashers Your hazard warning flashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will flash on and off. The hazard warning flasher button is located on top of the steering column.
Page 158: Tilt Wheel
Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. You can raise it to the highest level to give your legs more room when you exit and enter the vehicle. The lever that allows you to tilt the steering wheel is located on the left side of the steering column.
Page 159 Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically.
Page 160 Flash-to-Pass When the headlamps are off, pull the lever toward you to momentarily switch on the high beams (to signal that you are going to pass). When you release the lever, they will turn off. Windshield Wipers You control the windshield wipers by turning the band marked WIPER.
Page 161 Rear Window Washermiper The rear window washedwiper switch is located in the instrument panel switchbank. Push the wiper symbol on the top of the switch to turn on the intermittent wiper. To turn off the wiper, gently push the bottom of the switch. To wash and wipe the rear window, push in the washer symbol on the bottom of the switch.
Page 162 Setting Cruise Control If you leave your cruise control on when you’re not using cruise, you might hit a button and go into cruise when you don’t want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Page 163 Reducing Speed While Using Cruise Control There are two ways to reduce speed while using cruise control: Push in the SET button at the end of the lever until you reach the lower speed you want, then release it. To slow down in very small amounts, push the SET button briefly.
Page 164: Exterior Lamps
Exterior Lamps The control on the left side of the steering column operates the exterior lamps. The exterior lamp control has three positions: AUTO (Automatic Headlamp ControVOff): Turning the control to this position will activate the automatic headlamps when it is dark enough outside and turn off all lamps and lights during the day except for the Daytime Running Lamps (DRL).
Page 165 When the DRL are on, only your reduced intensity high-beam headlamps will be on. Your instrument panel won’t be lit up. When it’s dark enough outside, the exterior lamps will come on automatically. When it’s bright enough outside, the exterior lamps will go out and the DRL will turn on.
Page 166: Interior Lamps
Interior Lamps Your interior lamps control is located exterior lamps control. Instrument Panel Brightness This feature controls the brightness of the instrument panel lights. The knob for this feature is located on the interior lamps control. Press the knob and it will extend.
Page 167 Entry Lighting If your vehicle has entry lighting, the interior of your vehicle will illuminate for 25 seconds so you can see inside your vehicle before you enter. To activate entry lighting, do the following: Unlock a door using the key when the interior lamp control is in the DOOR position, and when the ignition is in OFF, or press UNLOCK on the remote keyless entry...
Page 168 Exit Lighting If your vehicle is equipped with exit lighting, the interior lamps will come on for about 30 seconds whenever you remove the key from the ignition if: The vehicle is in PARK (P), the key is out of the ignition, the interior lamp control is in the DOOR position, and all of the doors are closed.
Page 169: Instrument Panel Switchbank
Rear Reading Lamps There are two reading lamps with coat hooks above the rear doors. To turn on or either reading lamp, press the lens of the lamp. Cargo Lamp The cargo lamp is located in the rear of the vehicle, above the liftgate opening.
Page 170: Head-Up Display (Hud)
Head-Up Display (HUD) If the HUD image is too bright, your field of view, it may take you more time to see things you need to see when it’s dark outside. Be sure to keep the HUD image dim and placed in your field of view.
Page 171 Notice: Although the HUD image appears to be near the front of the vehicle, do not use it as a parking aid. The HUD was not designed for that purpose. If you try to use it as such, you may misjudge the distance and damage your vehicle.
Page 172 HUD image harder to see. When you first start the vehicle the display will show BUICK and the h i c k logo for a few seconds. If outside, this display may stay on for up to a minute. Clean the inside of the windshield as needed to remove any dirt or film that reduces the sharpness or clarity of the HUD image.
Page 173: Ultrasonic Rear Parking Assist (Urpa)
Ultrasonic Rear Parking Assist (URPA) The Ultrasonic Rear Parking Assist (URPA) system is designed to help you park, while the vehicle is in REVERSE (R). It operates only at very low speeds, less than 3 mph (5 km/h). URPA can help make parking easier and to help you avoid colliding with objects such as parked vehicles.
Page 174 System Works Unless disabled, the URPA will turn on automatically when the shift lever is moved into REVERSE (R). When the system turns on, the three lights on the display will illuminate for one and a half seconds to let you know that the system is working.
Page 175: Accessory Power Outlets
Accessory Power Outlets With accessory power outlets you can plug in electrical equipment such as a cellular telephone or CB radio. There is one front power outletlcigarette lighter located on the floor console in the cell phone storage compartment. There are also two rear power outlets. One is located in the rear of the floor console below the vents.
Page 176: Ashtrays And Cigarette Lighter
Ashtrays and Cigarette Lighter The ashtray is located on the floor console closest to the instrument panel. Lift the lid to expose the ashtray. The ashtray removes by lifting it The cigarette lighter is located on the floor console in the cell phone storage compartment closest to the driver’s seat.
Page 177: Climate Controls
Climate Controls Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. Operation Turn the right knob clockwise or counterclockwise to direct the airflow inside of your vehicle. To change the current mode, select one of the following: (Vent): This mode directs air to the instrument panel outlets.
Page 178 Temperature Control: Turn the center knob clockwise or counterclockwise to increase or decrease the air temperature inside your vehicle. (Air Conditioning): Press this button to turn the air-conditioning system on or off. When N C is pressed, an indicator light in the button will come on to let you know that air conditioning is activated.
Page 179: Dual Climate Control System
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. REAR: Press this button to turn the rear window defogger on or off. An indicator light in the button will come on to let you know that the rear window defogger is activated.
Page 180 (Bi-Level): This mode directs half of the air to the instrument panel outlets, then directs the remaining air to the floor outlets. Cooler air outlets and warmer air to the floor outlets. (Floor): This mode directs most of the air to the floor outlets.
Page 181 For quick cool down on hot days, do the following: 1. Select the vent mode. 2. Select the coolest temperature. 3. Select the highest fan speed. 4. Select N C . 5. Select the recirculation mode. Using these settings together for long periods of time may cause the air inside of your vehicle to become too dry.
Page 182: Dual Automatic Climate Control System
Dual Automatic Climate Control System Your vehicle may have the dual automatic climate control system. With this system you can control the heating, cooling and ventilation for your vehicle. Automatic Operation AUTO (Automatic): When the urivers iemperaiure knob is pressed to select AUTO and the temperature is set, the system will automatically control the inside temperature, the air delivery and the fan speed.
Page 183 Manual Operation MODE: Press this button to manually change the direction of airflow in your vehicle; keep pressing the button until the desired mode appears on the display. To change the current mode, select one of the following: (Vent): This mode directs air to the instrument panel outlets.
Page 184 You may notice a slight change in engine performance when the air-conditioning compressor shuts off and turns on again. This is normal. The system is designed to make adjustments to help with fuel economy while still maintaining the selected temperature. On hot days, open the windows to let hot escape;...
Page 185: Outlet Adjustment
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. REAR: Press this button to turn the rear window defogger on or off. An indicator light in the button will come on to let you know that the rear window defogger is activated.
Page 186: Warning Lights, Gages And Indicators
Warning Lights, Gages and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before becomes serious enough to cause an expensive repair or replacement.
Page 187: Instrument Panel Cluster
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, how much fuel you’re using, and many other things you’ll need to drive safely and economically. The indicator warning lights and gages are explained on the following pages.
Page 188: Speedometer And Odometer
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Your vehicle has a tamper-resistant odometer.
Page 189: Tachometer
Retro-Active Reset The trip odometer has a feature called retro-active reset. This feature can be used to set the trip odometer to the number of miles (kilometers) driven since the ignition was last turned on. This can be used if you forget to reset your trip odometer at the beginning of a trip.
Page 190: Air Bag Readiness Light
The safety belt light will also come on and stay on for several seconds. If the driver’s belt is already buckled, neither the chime nor the light will come on. Air Bag Readiness Light There is an air bag readiness light on the instrument panel, which shows the air bag symbol.
Page 191: Brake System Warning Light
Brake System Warning Light When the ignition is on, the brake system warning light will come on when you set your parking brake. The light will stay on if your parking brake doesn’t release fully. If it stays on after your parking brake is fully released, it means you have a brake problem.
Page 192: Anti-Lock Brake System Warning Light
Anti-Lock Brake System Warning Light ANTI LOCK States United Your vehicle may have an anti-lock brake system warning light. If it does, the light should come on for a few seconds when you turn the ignition key to ON. If the anti-lock brake system warning light stays on longer than normal after you've started your engine, turn the ignition off.
Page 193: Engine Coolant Temperature Gage
Engine Coolant Temperature Gage United States This gage shows the engine coolant temperature. If the gage pointer moves into the red area, your engine is too hot! It means that your engine coolant has overheated. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn off the engine as soon as possible.
Page 194 This system is called OBD I 1 (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The SERVICE ENGINE SOON or CHECK ENGINE light comes on to indicate that there is a problem and service is required.
Page 195 If the Light Is Flashing The following may prevent more serious damage to your vehicle: Reducing vehicle speed. Avoiding hard accelerations. Avoiding steep uphill grades. If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light stops flashing and remains on steady, see “If the Light Is On Steady”...
Page 196 Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See page Gasoline Octane on 5-5. Poor fuel quality will cause your engine not to run as efficiently as designed. You may notice this as stalling after start-up, stalling when you put the vehicle into gear, misfiring, hesitation on acceleration or stumbling on acceleration.
Page 197: Fuel Gage
Fuel Gage United States When the indicator nears empty, you still have a little fuel left, but you should get more soon. If your fuel is low, the warning message in the message center will come on. See Low Fuel Warning Message on page 3-53.
Page 198: Message Center
Message Center The message center is located at the top of the instrument panel cluster in between the tachometer and speedometer. It gives you important safety and maintenance facts. Service Traction System Warning Message SERVICE TRACTION SYSTEM United States ynir the traction control system and this vehicle ..
Page 199: Engine Coolant Temperature Warning Message
Engine Coolant Temperature Warning Message COOLANT TEMP United States This message will come on when your engine gets too hot. I f this message comes on, it means that your engine coolant has overheated. I f you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn engine as soon as possible.
Page 200: Low Oil Pressure Message
Low Oil Pressure Message PRESSURE United States Your vehicle is equipped with a low oil pressure warning message. Your oil pressure message lets you know when you may have a problem with your engine oil pressure. When the engine is running and this message appears, the engine oil level may be too low.
Page 201: Low Engine Oil Level Message
Low Engine Oil Level Message ENG OIL LEVEL United States If this message comes on, it means your engine is low on oil. You need to check the oil level right away. Have your vehicle serviced immediately. Change Engine Oil Message CHANGE ENGINE United States...
Page 202: Door Ajar Warning Message
Door Ajar Warning Message DOOR AJAR States United This message will come on when the ignition is turnea to ON or §TART and the driver’s or passenger’s door is open. Rear Hatch Ajar Warning Message AJAR States United This message will come on when the ignition is turnea to ON or §TART and the liftgate is open.
Page 203: All-Wheel Drive Disable Warning Message
All-Wheel Drive Disable Warning Message DISABLE United States Your vehicle may have this message. If it does, it will come on when there is a spare tire on the vehicle, or when the anti-lock brake system warning light comes on, or when the rear differential fluid is overheating. This message will go out when the differential fluid cools.
Page 204: Low Fuel Warning Message
Low Fuel Warning Message United States If your fuel is low, the warning message will come on and stay on until you add fuel. If the warning message is still on after adding fuel, you need to reset the warning message.
Page 205: Service Vehicle Soon Message
Service Vehicle Soon Message SERVICE VEHICLE SOON United States This light will come on if your vehicle has certain non-emission related problems. For example, if the entire electrical system fails to send and receive messages from the vehicle’s components, this message will come on. These problems may not be obvious and may affect vehicle performance or durability.
Page 206: Remote Keyless Entry Transmitter Battery Low Warning Message
Remote Keyless Entry Transmitter Battery Low Warning Message KEY FOB BATTERY States United If you receive this message, the battery in the remote keyless entry needs to be replaced. See "Battery Replacement" under Remote Keyless Entry System Operation on page 2-5 for instructions. Park Lamp Warning Message PARK LAMP L_____-...
Page 207: Driver Information Center (Dic)
Driver Information Center (DIC) DRIVER INFO CENTER NE AVG ECON 5.9 L/ 100 KM 6 5 F If your vehicle is equipped with the Driver Information Center (DIC), the display is located on the instrument panel cluster in the tachometer gage. The DIC will show information about the vehicle and the surroundings.
Page 208 Manual Compass Calibration If the compass appears erratic and the calibration symbol does not appear, you must manually put the compass into the calibration mode. To get into this mode, do the following: 1. Turn the ignition on and cycle the DIC to the compass/temperature mode.
Page 209: Dic Controls And Displays
DIC Controls and Displays When the ignition is turned to ON or START, the DIC will display the following: BUICK: BUICK will be displayed for three seconds. DRIVER This message will be displayed for another three seconds after BUCK appears in the display.
Page 210: Dic Vehicle Personalization
FUEL USED: The fuel used display will show you how much fuel has been used since the last time it was reset. To reset the fuel used to zero, press and hold the SET button while the fuel used is displayed on the DIC and until the display goes to zero.
Page 211 Entering Programming Mode To program features, your vehicle must be in the programming mode. Follow these steps: 1. Turn the ignition key to ON with the vehicle in PARK (P). 2. Press and release the MODE button, scrolling through the DIC messages, until PERSONALIZATION PRESS SET TO BEGIN is displayed.
Page 212 Before your vehicle was shipped from the factory, it was programmed in 30 second activation mode. The mode to which the vehicle has been programmed may have been changed since it left the factory. To determine the mode to which your vehicle is programmed or to program your vehicle to a different mode, do the following: 1.
Page 213 Interior Lighting On The interior lighting on feature can be programmed to one of the following modes: KEY OUT: The interior lamps will come on for about 25 seconds whenever you remove the key from the ignition. DOOR: The interior lamps will come on for about 25 seconds when any door is opened.
Page 214 Auto Door LocMUnlock The doors will automatically lock when the vehicle is shifted out of PARK (P). For automatic unlocking, you can program your vehicle to one of the following modes: OFF: When the shift lever is put in PARK doors will not unlock automatically.
Page 215 Delayed Locking The delayed locking feature can be programmed to one of the following modes: ON: Lock your vehicle using the power door lock switch or the remote keyless entry transmitter while any door is opened, you will hear three chimes and the doors will not lock.
Page 216 ALL: All doors will unlock with every press of UNLOCK on the remote keyless entry transmitter. Before your vehicle was shipped from the factory, programmed in ALL. The mode to which the vehicle has been programmed may have been changed since it left the factory.
Page 217 Before your vehicle was shipped from the factory, it was programmed in LIGHTS. The mode to which the vehicle has been programmed may have been changed since it left the factory. To determine the mode to which your vehicle is programmed or to program your vehicle to a different mode, do the following: Follow the instructions for “Entering Programming Mode”...
Page 218 1. Follow the instructions for ”Entering Programming Mode” listed previously. 2. Press the MODE button until LOCK FEEDBACK appears the DIC. 3. Press the SET button until the arrow is before OFF, LIGHTS or LIGHTS and HORN. The mode you selected is now set. Seat Recal I The seat recall feature can be programmed to one of the following modes:...
Page 219 Tilt Mirror The tilt mirror feature can be programmed to one of the following modes: ON: The passengers side outside rearview mirror will tilt down towards the curb when the vehicle is shifted to REVERSE (R) and returns to its previous position when the vehicle is shifted out of REVERSE (R).
Page 220: Audio System(S)
Audio System(s) Notice: Before you add any sound equipment to your vehicle like a tape player, CB radio, mobile telephone or two-way radio be sure you can add what you want. If you can, it’s very important to properly. Added sound equipment may interfere with the operation of your vehicle’s engine, Delphi Electronics radio or other systems, and even damage them.
Page 221 Playing the Radio PWR (Power): Push this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease the volume. DlSP (Display): Press this button to switch the display between the radio station frequency and the time. The time can be displayed with the ignition on or off.
Page 222 Setting Preset Stations numbered pushbuttons let you return to your favorite stations. You can set up to 18 stations (six AM, FMI and six FM2) by performing the following steps: Turn the radio on. Press BAND to select AM, FMI or FM2. Tune in the desired station.
Page 223 Adjusting the Speakers (Balance/Fade) AUDIO: To adjust the balance between the right and the left speakers, push and release AUDIO until BAL appears on the display. Then turn the AUDIO knob to move the sound toward the right or the left speakers. A bar graph with indicators will show how the sound is balanced between the right and the left speakers.
Page 224 Finding a PTY Station To select and find a desired PTY perform the following: Press P-TYP. The PTY symbol will be displayed on the screen. Select a category by turning the AUDIO knob. Once the desired category is displayed, press either SEEK arrow to select the category and take you to the category’s first station.
Page 225 RDS Messages ALERT!: Alert warns of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! will appear on the display. You will hear the announcement, even if the volume is muted or a compact disc is playing. If a compact disc is playing, play will stop during the announcement.
Page 226 (Reverse): Press and hold this pushbutton to quickly reverse within a track. Release is it to play the passage. You will hear sound at a reduced level. (Forward): Press and hold this pushbutton to quickly advance within a track. Release it to play the passage.
Page 227: Radio With Cassette And Cd
Compact Disc Errors CHECK CD: If this message appears on the radio display, it could be due to one of the following reasons: You’re driving on a very rough road. When the road is smoother, the disc should play. The disc is dirty, scratched, wet or upside down. The air is very humid.
Page 228 This system relies upon receiving specific information from these stations and will only work when the information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, contact the radio station.
Page 229 DlSP (Display): Press this button to switch the display between the radio station frequency and the time. Time display is available with the ignition turned off. For XMTM (USA only, if your radio is equipped with XMTM Satellite Radio Service), pressing this button while in XMTM mode to retrieve various pieces of information related to the current song or channel.
Page 230 Setting Preset Stations The six numbered pushbuttons let you return to your favorite stations. You can set up to six FM1 and six FM2, six XMI and six XM2 (USA only, if your radio is equipped with the XMTM Satellite Radio Service) or DAB1 and DAB2 (Canada only, if your radio is equipped with DAB), by performing the following steps:...
Page 231 Adjusting the Speakers (Balance/Fade) AUDIO: To adjust the balance between the right and the left speakers, push and release AUDIO until BAL appears on the display. Then turn the AUDIO knob to move the sound toward the right or the left speakers. A bar graph with indicators will show how the sound is balanced.
Page 232 SCAN: You can also scan through the stations within a category by performing the following: 1. Press P-TYP. The PTY symbol will be displayed on the screen. 2. Select a category by turning the AUDIO knob. 3. Once the desired category is displayed, press and hold either SEEK arrow, and the radio will begin scanning within your chosen category.
Page 233 TRAF (Traffic): TRAF will appear on the display if the tuned station broadcasts traffic announcements. To receive the traffic announcement from the tuned station, press this button. Brackets will be displayed around TRAF and when a traffic announcement comes tuned radio station you will hear it. If the current tuned station does not broadcast traffic announcements, press this button and the radio will seek to a station that does.
Page 234 Radio Messages CAL (CALIBRATE): Your audio system has been calibrated for your vehicle from the factory. If this message appears on the display it means that your radio has not been configured properly for your vehicle and must be returned to the dealership for service. Radio Display Message...
Page 235 Radio Display Message No Info Artist Name/Feature not available No Info Song/Program Title not available No Info Category Name not available No Texthformational message available No Info No channel available for Not Found the chosen category XM Locked Theft lock active Radio ID Radio ID label (channel 0)
Page 236 Playing a Cassette Tape The longer side with the tape visible should face to the right. If the ignition and the radio are on, the tape can be inserted and will begin playing. If you hear nothing or hear a garbled sound, the tape may not be in squarely.
Page 237 Cassette Tape Messages If an error message appears while trying to play a cassette tape, it could be for one of the following reasons: TIGHT TAPE: The tape is tight and the player can’t turn the tape hubs. Remove the tape. Hold the tape with the open end down and try to turn the right hub counterclockwise with a pencil.
Page 238 (Reverse): Press and hold this pushbutton to quickly reverse within a track. You will hear sound. (Forward): Press and hold this pushbutton to quickly advance within a track. You will hear sound. 4 RDM (Random): Press this pushbutton to hear the tracks in random, rather than sequential, order.
Page 239: Radio With Six-Disc Cd
Radio with Six-Disc CD Radio Data System (RDS): Your audio system is equipped with a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. Seek to stations broadcasting the selected type of programming, receive announcements concerning local and national emergencies,...
Page 240 Playing the Radio PWR (Power): Push this knob to turn the system on and off. VOL (Volume): Turn the knob to increase or to decrease volume. AUTO VOL (Automatic Volume): Your system has a feature called automatic volume. With this feature, your audio system adjusts automatically to make up for road and wind noise as you drive.
Page 241 Finding a Station BAND: Press this button to switch between AM, FM, FM2, or XM1, XM2 (USA only, if your radio is equipped with XMTM Satellite Radio Service) or DABI, DAB2 (Canada only, if your radio is equipped with DAB). The display will show your selection.
Page 242 4. Press AUTO EQ to select the equalization. 5. Press and hold one of the six numbered pushbuttons until you hear a beep. Whenever you press that numbered pushbutton, the station you set will return and the equalization that you selected will also be automatically selected for that pushbutton.
Page 243 Finding a PTY Station (RDS, XMTM and DAB) To select and find a desired PTY perform the following: 1. Press the P-TYPE button. P-TYPE and the last selected PTY will be displayed on the screen. 2. Select a category by turning the P-TYPE knob. 3.
Page 244 Setting Preset PTYs (RDS Only) The six numbered pushbuttons let you return to your favorite PTYs. These buttons have factory PTY presets. You can set up to 12 PTYs (six FMI and six FM2) by performing the following steps: 1. Press BAND to select FMl or FM2. 2.
Page 245 TRAF (Traffic): TRAF will appear on the display if the tuned station broadcasts traffic announcements. To receive the traffic announcement from the tuned station, press this button. Brackets will be displayed around TRAF and when a traffic announcement comes on the tuned radio station you will hear it.
Page 246 Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. Updating encryption Updating code No Info Artist Name/Feature not available Song/Program Title not No Info available XMTM Radio Messages Condition These channels, or any others, can be blocked at a customer’s request, by calling 1 -800-852-XMXM (9696).
Page 247 Radio Display Message No Info Category Name available No Info No TexVlnformational message available Not Found No channel available for the chosen category XM Locked Theft lock active Radio ID Radio (channel 0) Unknown Radio (should only be if hardware failure) Chk XMRcvr Hardware 3-96 XMTM Radio Messages (cont’d)
Page 248 Playing a Compact Disc If an error appears on the display, see “Compact Disc Messages” later in this section. LOAD CD : Press the LOAD side of this button to load CDs into the compact disc player. This compact disc player will hold up to six discs. To insert one disc, do the following: 1.
Page 249 Playing a Specific Loaded Compact Disc For every CD loaded, a number will appear on the radio display. To play a specific CD, first press the CD AUX button to start playing a CD. Then press the numbered pushbutton that corresponds to the CD you want to play.
Page 250 RDM (Random): With random, you can listen to the tracks in random, rather than sequential, order, on one disc or on all of the discs. To use random, do one of the following: To play the tracks on the disc you are listening to in random order, press and hold RDM for more than two seconds.
Page 251 Using Song List Mode The integrated six-disc CD changer has a feature called song list. This feature is capable of saving 20 track selections. To save tracks into the song list feature, perform the following steps: 1. Turn the disc player on and load disc.
Page 252: Entertainment System
To delete the entire song list, perform the following steps: 1. Turn the disc player on. 2. Press the SONG LIST button to turn song list on. S-LIST will appear on the display. 3. Press and hold the SONG LIST button for more than four seconds.
Page 253 Headphones The entertainment system includes wireless headphones. The wireless headphones have an ON/OFF switch, and a volume control. To use the headphones turn the switch to ON. An indicator light will illuminate. If the light does not illuminate, the batteries may need to be replaced.
Page 254 If a disc is not present in the player, the auxiliary signal will immediately be displayed on the entertainment system. If a disc is present when the entertainment system power is turned on, the player will automatically begin playing the disc and the user will need to press the SRCE button on the remote control or on the DVD player faceplate to display the auxiliary input signals.
Page 255 The entertainment system is only compatible with Region 1 DVDs authorized for use in the United States, Canada, Puerto Rico, Bermuda, the Virgin Islands, and some islands in the Pacific. On some DVD jackets, you will see the region displayed. Regular audio CDs can also be played by the DVD player.
Page 256 Playing a Disc To play a disc, gently insert the disc (with the label side up) into the loading slot. The DVD player will continue loading the disc and the player will automatically start. If a disc is already in the player, press the play/pause button on the face of the player or on the remote control.
Page 257 Remote Control To use the remote control, aim it at the display above the video screen and press the desired button. Direct sunlight or very bright light may affect the ability of the entertainment system to receive signals from the remote control. Be sure the remote’s batteries are not discharged, as this will also affect the function of the remote control.
Page 258 D. Display Control Button: Press this button to adjust color, tint, brightness, contrast, and display mode (normal, full or zoom). This button is also used to adjust the dynamic range compression feature that is used to avoid the loud noise produced by some DVD discs, and to improve the audio quality.
Page 259 Setup Menu To access the setup menu, ensure a DVD disc is in the player and the video is stopped. Press the main menu button. Once the menu is activated, use the directional arrows and enter button to navigate the screen. The setup menu allows the user to select default preferences for Menu Language, Subtitle Language, Audio Language, TV Aspect, TV Mode, and Dynamic...
Page 260 Tips and Trouble Recommended Action Problem The ignition might be off. No power. The InpuVTitle on the Disc will not play. remote might be set for auxiliary. The disc is upside down or is not compatible. The volume on the No sound.
Page 261: Rear Seat Audio (Rsa)
Problem Recommended Action The audio or video skips The DVD could be dirty or or jumps. scratched. Try cleaning the DVD. When I return to the DVD If the stop button was from the main menu, pressed once, it resumes sometimes it plays from play from where it left the beginning and...
Page 262 Primary Radio Controls The following function is controlled by the knob on the main radio: PWR (Power): Push this knob twice to turn RSA off. Rear Seat Radio Controls The following functions are controlled by the RSA system burtons: PWR (Power): Press this button to turn RSA on or off. VOL (Volume): Press this knob lightly so Turn the knob to increase or to decrease volume.
Page 263: Theft-Deterrent Feature
To scan stations, press and hold one of the SEEK arrows until the radio goes into scan mode. The radio will scan to a station, play for a few seconds, then go on to the next station. Press SEEK again to stop scanning. The scan function is inactive if front radio is in use.
Page 264: Audio Steering Wheel Controls
Audio Steering Wheel Controls If your vehicle has this feature, you can control certain radio functions using the buttons on your steering wheel. SOURCE: Press this button to play a cassette tape or compact disc when listening to the radio. If a cassette tape and a compact disc are both loaded, the system will go to the tape play first.
Page 265: Understanding Radio Reception
Understanding Radio Reception The range for most AM stations is greater than for FM, especially at night. The longer range, however, can cause stations to interfere with each other. AM can pick up noise from things like storms and power lines. Try reducing the treble to reduce this noise if you ever get it.
Page 266: Care Of Your Cds And Dvds
The cut tape detection feature of your cassette tape player may identify the cleaning cassette tape as a damaged tape, in error. If the cleaning cassette ejects, insert the cassette at least three times to ensure thorough cleaning. You may also choose a non-scrubbing action, wet-type cleaner which uses a cassette with a fabric belt to clean the tape head.
Page 267: Cleaning The Video Screen
Cleaning the Video Screen When cleaning the video screen, use only a clean cloth dampened with clean water. Use care when directly touching or cleaning the screen, as damage may result. Integrated Windshield Antenna The antenna in your vehicle is a very thin, metal layer in the windshield.
Page 268: Driving Your Vehicle
Section Your Driving. the Road. and Your Vehicle Driver Behavior Driving Environment Vehicle Design Defensive Driving Drunken Driving Control of a Vehicle Braking Traction Control System (TCS) All-Wheel Drive (AWD) System Steering Off-Road Recovery ... Passing ... Loss of Control Driving at Night Driving Your Vehicle Driving in Rain and...
Page 269: Your Driving. The Road. And Your Vehicle
Your Driving, the Road, and Your Vehicle Whenever we drive, we’re taking on an important responsibility. This is true for any motor vehicle passenger car, van, truck, sport utility. Driver behavior, the driving environment, and the vehicle’s design all affect how well a vehicle performs. But statistics show that the most important factor, by far, is how we drive.
Page 270: Vehicle Design
Vehicle Design According to the US. Department of Transportation, utility vehicles have a significantly higher rollover rate than other types of vehicles. Utility vehicles do have higher ground clearance and a narrower track or shorter wheelbase than passenger cars, to make them more capable for off-road driving.
Page 271: Drunken Driving
Drunken Driving Death and injury associated with drinking and driving is a national tragedy. It’s the number one contributor to the highway death toll, claiming thousands of victims every year. Alcohol affects four things that anyone needs to drive a vehicle: Judgment Muscular Coordination...
Page 272 It’s the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 mI of liquor each) within an hour, the person’s would be close to percent. A person 0.12 who consumes food just before or during drinking will have a somewhat lower BAC level.
Page 273 The body takes about an hour to rid itself of the alcohol in one drink. No amount of coffee or number of cold showers will speed that up. “1’11 be careful” isn’t the right answer. What if there’s an emergency, a need to take sudden action, as when a child darts into the street? A person with even a moderate BAC might not be able to react quickly enough to avoid the collision.
Page 274: Control Of A Vehicle
Control of a Vehicle You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering and the accelerator. All three systems have to do their work at the places where the tires meet the road. Sometimes, as when you’re driving on snow or ice, it’s easy to ask more of those control systems than the ruau...
Page 275 Avoid needless heavy braking. Some people drive in spurts heavy acceleration followed by heavy braking rather than keeping pace with traffic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear out much faster if you do a lot of heavy braking.
Page 276 Let’s say the road is wet and you’re driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here’s what happens with ABS: A computer senses that wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each wheel.
Page 277 As you brake, your computer keeps receiving updates on wheel speed and controls braking pressure accordingly. Remember: Anti-lock doesn’t change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you won’t have time to apply your brakes if that vehicle suddenly slows or stops.
Page 278: Traction Control System (Tcs)
Traction Control System (TCS) Your vehicle may have a traction control system that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that one or both of the front wheels are spinning or beginning to lose traction.
Page 279: All-Wheel Drive (Awd) System
To turn the system off, press the TRAC OFF button located on the instrument panel switchbank. If the system is limiting wheel spin when you press the button, the message will go off, but the system will not turn off until there is no longer a current need to limit wheel spin.
Page 280 Steering Tips Driving on Curves It’s important to take curves at a reasonable speed. A lot of the “driver lost control” accidents mentioned on the news happen on curves. Here’s why: Experienced driver or beginner, each of us is subject to the same laws of physics when driving on curves.
Page 281 Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 282: Off-Road Recovery
Off-Road Recovery You may find that your right wheels have dropped off the edge of a road onto the shoulder while you’re driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement.
Page 283: Loss Of Control
Do not get too close to the vehicle you want to pass while you’re awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you’re following a larger vehicle. Also, you won’t have adequate space if the vehicle ahead suddenly slows or stops.
Page 284 Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not “overdriving” those conditions. But skids are always possible. The three types of skids correspond to your vehicle’s three control systems.
Page 285: Driving At Night
Driving at Night Night driving is more dangerous than day driving. One reason is that some drivers are likely to be impaired by alcohol or drugs, with night vision problems, or by fatigue. Here are some tips on night driving. Drive defensively.
Page 286: Driving In Rain And On Wet Roads
You can be temporarily blinded by approaching headlamps. It can take a second or two, or even several seconds, for your eyes to re-adjust to the dark. When you are faced with severe glare (as from a driver who doesn’t lower the high beams, or a vehicle with misaimed headlamps), slow down a little.
Page 287 The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traffic signals, pavement markings, the edge of the road and even people walking.
Page 288 Hydroplaning Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you’re going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road. Hydroplaning doesn’t happen often.
Page 289: City Driving
City Driving 4-22 One of the biggest problems with city streets is the amount of traffic on them. You’ll want to watch out for what the other drivers are doing and pay attention to traffic signals. Here are ways to increase your safety in city driving: Know the best way to get to where you are going.
Page 290: Freeway Driving
Freeway Driving Mile for mile, freeways (also called thruways, parkways, expressways, turnpikes or supeinignwaysj are ihe safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving.
Page 291: Before Leaving On A Long Trip
When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up. Drive on to the next exit. The exit ramp can be curved, sometimes quite sharply. The exit speed is usually posted.
Page 292: Highway Hypnosis
Highway Hypnosis Is there actually such a condition as “highway hypnosis”? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
Page 293 If you drive regularly in steep country, or if you’re planning to visit there, here are some tips that can make your trips safer and more enjoyable. Keep your vehicle in good shape. Check all fluid levels and also the brakes, tires, cooling system and transaxle.
Page 294: Winter Driving
As you go over the top of a hill, be alert. There could be something in your lane, like a stalled car or an accident. You may see highway signs on mountains that warn of special problems. Examples are long grades, passing'or no-passing zones, a falling rocks alert area or winding roads.
Page 295 Driving on Snow or Ice Most of the time, those places where your tires meet the road probably have good traction. However, if there is snow or ice between your tires and the road, you can have a very slippery situation. You’ll have a lot less traction or “grip”...
Page 296 If you don’t have a traction system, accelerate gently. Try not to break the gentle traction. If you accelerate too fast, the drive wheels will spin and polish the surface under the tires even more. Unless you have the anti-lock braking system, you’ll want to brake very gently, too.
Page 297 If You’re Caught in a Blizzard If you are stoppd by heavy snow, you could be in a serious situation. You should probably stay with your vehicle unless you know for sure that you are near help and you can hike through the snow. Here are some things to do to summon help and keep yourself and your passengers safe: Turn on your hazard flashers.
Page 298 Snow can trap exhaust gases ,,,der vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You can’t see it or smell it, so you might not know it is in your vehicle.
Page 299: If You Are Stuck: In Sand, Mud, Ice Or Snow
If You Are Stuck: In Sand, Mud, Ice or Snow In order to free your vehicle when it is stuck, you will need to spin the wheels, but you don’t want to spin your wheels too fast. The method known as “rocking” can help you get out when you’re stuck, but you must use caution.
Page 300: Towing
Towing Towing Your Vehicle Consult your dealer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Assistance Program on page 7-5. If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see “Recreational Vehicle Towing”...
Page 301: Loading Your Vehicle
Dolly Towing If you have a two-wheel-drive vehicle, it can be towed with two of its wheels on the ground. To dolly tow your vehicle, do the following: 1. Put the front wheels on a dolly. 2. Put the vehicle in PARK (P). 3.
Page 302 The Certification/Tire label also tells you the maximum weights for the front and rear axles, called the Gross Axle Weight Rating (GAWR). To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle.
Page 303 Automatic Level Control On vehicles equipped with the automatic level control, the rear of the vehicle is automatically kept level as you load or unload your vehicle. However, you should still not exceed the GVWR or the GAWR. If the key is in ACCESSORY, ON or when Retained Accessory Power (RAP) is active, you may hear the compressor operating when you load your vehicle or shortly after you start your vehicle, and periodically as...
Page 304 Your vehicle can tow a trailer. To identify what the vehicle trailering capacity is for your vehicle, you should read the information in “Weight of the Trailer’’ that appears later in this section. But trailering is different than just driving your vehicle by itself. Trailering means changes in handling, durability and fuel economy.
Page 305 You can ask your dealer for our trailering information or advice, or you can write us at: Buick Customer Assistance Center P.O. Box 33136 Detroit, MI 48232-51 36 In Canada, write to:...
Page 306 If you’re using a weight-carrying or a weight-distributing hitch, the trailer tongue weight (A) should be 10 percent to 15 percent of the total loaded trailer weight (B). Do not exceed the maximum allowable tongue weight for your vehicle. Atter you’ve ioaaea your iraiier, weiyil then the tongue, separately, to see if the weights are proper.
Page 307 Safety Chains You should always attach chains between your vehicle and your trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer.
Page 308 Towing a trailer requires a certain amount of experience. Before setting out for the open road, you’ll want to get to know your rig. Acquaint yourself with the feel handling and braking with the added weight of the trailer. And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as responsive as your vehicle is by itself.
Page 309 Turn Signals When Towing a Trailer When you tow a trailer, your vehicle has to have extra wiring. The arrows on your instrument panel will flash whenever you signal a turn or lane change. Properly hooked up, the trailer lamps will also flash, telling other drivers you’re about to turn, change lanes or stop.
Page 310 When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: start your engine, shift into a gear, and release the parking brake. 2. Let up on the brake pedal. 3.
Page 312: Service And Appearance Care
Section 5 Service Doing Your Own Service Work Adding Equipment to the Outside of Your Vehicle Fuel Gasoline Octane Gasoline Specifications California Fuel Additives Fuels in Foreign Countries Filling Your Tank Fi!!Ing a Portab!e Fue! Container Checking Things Under the Hood Hood Release Engine Compartment Overview Engine Oil...
Page 313 Section 5 Uniform Tire Quality Grading Wheel Alignment and Tire Balance Wheel Replacement Tire Chains ... Accessory Inflator If a Tire Goes Flat ... Changing a Flat Tire ... Compact Spare Tire ... Appearance Care ... Cleaning the Inside of Your Vehicle ... 5-87 Care of Safety Belts ...
Page 314: Service
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you’ll go to your dealer for all your service needs. You’ll get genuine GM parts and GM-trained and supported service people. We hope you’ll want to keep your GM vehicle all GM. Genuine GM parts have one of these marks:...
Page 315: Doing Your Own Service Work
Doing Your Own Service Work If you want to do some of your own service work, you’ll want to use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-9.
Page 316: Fuel
Fuel Use of the recommended fuel is an important part of the proper maintenance of your vehicle. Gasoline Octane Use regular unleaded gasoline with a posted octane of 87 or higher. If the octane is less than 87, you may get a heavy knocking noise when you drive.
Page 317: California Fuel
California Fuel If your vehicle is certified to meet California Emission Standards (see the underhood emission control label), is designed to operate on fuels that meet California specifications. If this fuel is not available in states adopting California emissions standards, your vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance may be affected.
Page 318: Fuels In Foreign Countries
Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada, the proper fuel may be hard to find. Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel wouldn't be covered by your warranty.
Page 319 To remove the fuel cap, turn it slowly to the left (counterclockwise). The fuel cap has spring in it; if you let go of the cap too soon, it will spring back to the right. If you get fuel on yourself and then something ignites it, you could be badly burned.
Page 320 Filling a Portable Fuel Container Never fill a portable fuel container your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: Dispense gasoline only into approved containers.
Page 321: Checking Things Under The Hood
Checking Things Under the Hood An electric fan under the hood can start and injure you even when the engine is not running. Keep hands, clothing and tools away from any underhood electric fan. 5-1 0 CAUTI Things that burn can get on hot engine parts and start a fire.
Page 322: Hood Release
Hood Release To open the hood: Pull the hood release handle, located on the driver's side under the instrument panel. Go to the front of the vehicle and slide the secondary hood release handle from left to right. Lift the hood. If your vehicle has a prop rod, place it in the slot on the underside of the hood.
Page 323: Engine Compartment Overview
Engine Compartment Overview When you lift the hood, you’ll see these items: 5-1 2...
Page 324: Engine Oil
A. Underhood Fuse Block B. Remote Positive (+) Terminal C. Power Steering Fluid Reservoir D. Automatic Transaxle Fluid Dipstick E. Brake Master Cylinder F. Windshield Washer Fluid Reservoir G. Battery H. Radiator Pressure Cap I. Engine Oil Fill Cap J. Engine Oil Dipstick K.
Page 325 Checking Engine Oil It’s a good idea to check your engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick is located at the front of the engine compartment, near the center.
Page 326 The engine oil fill cap is located iust behind the engine Ail dipstick. SAE 5W-30 ‘I See Engine Compartment Overview on page 5-12 for more information on location. Be sure to iiii ii enough pui the ievei somewhere in the proper operating range in the cross-hatched area.
Page 327 RECOMMENDED SAE VISCOSITY GRADE ENGINE OILS LOOK WEATHER SYMBOL "C ' O F . t38 + l o o - - + 2 7 + 8 0 - + 6 0 - - + 4 0 - - + 2 0 - - - - I ACCEPTABLE 1OW-30...
Page 328 When to Change Engine Oil (GM Oil Life SystemTM) Your vehicle has a computer system that lets you know when to change the engine oil and filter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change will be indicated can vary considerably.
Page 329 What to Do with Used Oil Used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer. Don’t let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner.
Page 330: Automatic Transaxle Fluid
5. Align the tabs located on the bottom of the panel with the slots at the bottom of the housing. 6. Latch the hooks to secure the panel in place. If the panel moves easily, check that the tabs are seated correctly in the slots.
Page 331 How to Check Because this operation can be a little difficult, you may choose to have this done at the dealership service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick. Notice: Too much or too little fluid can damage your transaxle.
Page 332 The dipstick handle is a bright red loop. See Engine Compartment Overview on page 5-12 for more information on location. 1. Pull out the dipstick and wipe it with a clean rag or paper towel. 2. Push it back in all the way, wait three seconds and then pull it back out again.
Page 333 Engine Coolant The cooling system in your vehicle is filled with DEX-COOL@ engine coolant. This coolant is designed to remain in your vehicle for 5 years or 150,000 miles (240 000 km), whichever occurs first, if you add only DEX-COOL@ extended life coolant. The following explains your cooling system and how to add coolant when it is low.
Page 334 Adding plain water yvur cvv,...g OL,,, system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you wouldn’t get the overheat warning.
Page 335 Adding Coolant If you need more coolant, add the proper DEX-COOL@ coolanf recovery tank. coolant Turning .,re rad,,,or press,,e engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly. With the coolant recovery tank, you will almost never have to add coolant at the radiator.
Page 336: Radiator Pressure Cap
Radiator Pressure Cap Notice: Your radiator cap is a pressure-type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheating. Be sure the arrows on the cap line up with the overflow tube on the radiator filler neck. The radiator pressure cap is located at the front of the engine compartment on the passenger’s side of the vehicle.
Page 337 If Steam Is Coming From Your Engine Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get CAUTION: (Continued) 5-26 e-,ryone away fr-..] the vehicl-...
Page 338 No Steam Coming From Your Engine If you get an engine overheat warning but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you: Climb a long hill a hot day.
Page 339: Cooling System
Cooling System When you decide it’s safe to lift the hood, here’s what you’ll see: A. Radiator Pressure Cap B. Electric Engine Cooling Fans C. Coolant Recovery Tank 5-28 An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you.
Page 340 The coolant level should be at or above the FULL COLD mark. If it isn’t, you may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling Heater and radiator hoses, and other engine parts, can be very hot.
Page 341 How to Add Coolant to the Coolant Recovery Tank If you haven’t found a problem yet, but the coolant level isn’t at or above the FULL COLD mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL@ engine coolant at the coolant recovery tank. See Engine Coolant on page 5-22 for more information.
Page 342 When the coolant in the coolant recovery tank is at or above the FULL COLD mark, start your vehicle. If the overheat warning continues, there’s one more thing you can try. You can add the proper coolant mixture directly to the radiator, but be sure the cooling system is cool before you do it.
Page 343 How to Add Coolant to the Radiator Notice: Your engine has a specific radiator fill procedure. Failure to follow this procedure could cause your engine to overheat and be severely damaged. 1. You can remove the radiator pressure cap when the cooling system, including the radiator pressure cap and upper radiator hose, is no longer hot.
Page 344 Housing 3. After the engine cools, open the coolant air bleed valves. There are two bleed valves. One thermostat housing. The other is located on the thermostat bypass tube. Bypass Tube 4. Fill the radiator with the proper DEX-COOL@ located on the coolant mixture, up to the base of the filler neck.
Page 345 6. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fans. 7. By this time, the coolant level inside the radiator filler neck may be lower. If the level is lower, add more of the proper DEX-COOL@ coolant mixture through the filler neck until the level reaches the base of the filler neck.
Page 347: Windshield Washer Fluid
When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss in this system could indicate a problem. Have the system inspected and repaired.
Page 348: Brakes
Notice: When using concentrated washer fluid, follow the manufacturer's instructions for adding water. Don't mix water with ready-to-use washer fluid. Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system. Also, water doesn't clean as well as washer fluid.
Page 349 There are only two reasons why the brake fluid level in the reservoir might go down. The first is that the brake fluid goes down to an acceptable level during normal brake lining wear. When new linings are put in, the fluid level goes back up.
Page 350 What to Add When you do need brake fluid, use only DOT-3 brake fluid. Use new brake fluid from a sealed container only. See Part D: Recommended Fluids and Lubricants on page 6- 15. Always clean the brake fluid reservoir cap and the area around the cap before removing it.
Page 351: Battery
Notice: .,Continuing to drive with worn-out brake pads could result in costly brake repair. Some driving conditions or climates may cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with your brakes.
Page 352: Jump Starting
Vehicle Storage If you’re not going to drive your vehicle for 25 days or more, remove the black, negative (-) cable from the battery. This will help keep your battery from running down. Batteries have acid that can burn you and gas that can explode.
Page 353 Notice: If the other system isn’t a 12-volt system with a negative ground, both vehicles can be damaged. 2. Get the vehicles close enough so the jumper cables can reach, but be sure the vehicles aren’t touching each other. If they are, it could cause a ground connection you don’t want.
Page 354 Using a ma.-.i near a ry can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water. You don’t need to add water to the ACDelco@ battery installed in your new vehicle.
Page 355 7. Don’t let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 5-44 Don’t let the other end touch anything until the next step.
Page 356 Notice: Damage to your vehicle may result from electrical shorting if jumper cables are removed incorrectly. To prevent electrical shorting, take care that the cables don’t touch each other or any other metal. The repairs wouldn’t be covered by your warranty. Jumper Cable Removal A.
Page 357: All-Wheel Drive
All-Wheel Drive If you have an all-wheel-drive vehicle, be sure to perform the lubricant checks described in this section. However, they have two additional systems that need lubrication. Transfer Case (Power Transfer Unit) When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant.
Page 358 Carrier Assembly-Differential (Rear Drive Module) When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See Part A: Scheduled Maintenance Services on page 6-4. How to Check Lubricant To get an accurate reading, the vehicle should be on a surface.
Page 359: Bulb Replacement
Bulb Replacement For the type of bulbs, see Replacement Bulbs page 5-52. For any bulb changing procedure not listed in this section, contact your dealer. Halogen Bulbs --..x Haloger. have press-. .zed gas inside and can burst if you drop or scratch the bulb. You or others could be injured.
Page 360 6. Turn the bulb socket one-quarter of a turn clockwise. 7. Pull the bulb assembly out from the lamp housing. Unhook the electrical connector by lifting up the gray tabs and separate the connector from the bulb base. Install the new bulb into the electrical connector. Push the bulb firmly enough so that the gray tabs hook over the tab on the bulb.
Page 361: Front Turn Signal, Sidemarker And Parking Lamps
10. Put the bulb assembly back into the lamp housing and turn the bulb socket one-quarter of a turn counterclockwise. Align the retaining clips on the back of the headlamp with the rectangular holes in the mounting panel. 12. Push firmly on both ends of the headlamp to snap it into position.
Page 362: Taillamps And Back-Up Lamps
7. Install the new bulb into the electrical connector. Push the bulb firmly enough so that the tabs hook over the tab on the bulb. 8. Put the bulb assembly back into the lamp housing and turn the bulb socket one-quarter of a turn clockwise.
Page 363: Replacement Bulbs
A. Taillamp (outboard) B. Taillamp (center) C. Back-up Lamp (inboard) 6. Turn the bulb socket one-quarter of a turn counterclockwise. 7. Pull the bulb assembly out from the lamp housing. 8. Pull the bulb out of the base. 9. Install the new bulb into the electrical connector. Push the bulb firmly enough so that the tabs hook over the tab on the bulb.
Page 364: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear or cracking. See "Wiper Blade Check" under Part B: Owner Checks and Services page 6-9 for more information. Replacement blades come in different types and are removed in different ways.
Page 365 5. Push the new wiper blade securely on the wiper arm until you hear the release clip "click" into place. 6. Push the release clip, from Step 4, down to secure the wiper blade into place. To replace the backglass mounted wiper blade, do the following: 1.
Page 366: Tires
Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your Buick Warranty booklet for details. aintained and improperly are dangerous. Overloading your tires can cause overheating as a result of too much friction.
Page 367: Inflation Tire Pressure
Inflation Tire Pressure The Certificationrrire label, which is on the rear edge of the driver’s door, shows the correct inflation pressures for your tires when they’re cold. “Cold” means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km).
Page 368 The LOW TIRE PRESSURE HOLD SET TO RESET message will appear on the Driver Information Center (DIC) and the LOW TIRE PRESSURE message will come on the message center if pressure difference (low pressure) is detected in one tire. In the following conditions, the LOW TIRE PRESSURE message may not come on even if the tire pressure is low, or it may come on when the tire pressure is actually normal:...
Page 369: Tire Inspection And Rotation
You will hear three chimes and the LOW TIRE PRESSURE message will go off and the DIC will return to TIRE PRESSURE NORMAL. If the LOW TIRE PRESSURE message comes back on, the check tire pressure system has not reset. Repeat the procedure. The system completes the calibration process during driving.
Page 370: When It Is Time For New Tires
Reset the check tire pressure system, if equipped. See Check Tire Pressure System on page 5-56. Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 5- 102. Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time.
Page 371: Buying New Tires
The tread or sidewall is cracked, cut or snagged deep enough to show cord or fabric. The tire has a bump, bulge or split. The tire has a puncture, cut or other damage that can’t be repaired well because of the size or location of the damage.
Page 372: Uniform Tire Quality Grading
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, traction and temperature performance.
Page 373: Wheel Alignment And Tire Balance
Temperature A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 374 If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle. A n g the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be dangerous.
Page 375: Tire Chains
Tire Chains - ,R16 If your vehicle has P2‘. use tire chains, there’s not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicleparts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash.
Page 376: Accessory Inflator
Accessory Inflator Your vehicle may have an air inflator. With it, you can inflate things like air mattresses and basketballs, and you can also use it to bring your tires up to the proper pressure. The air inflator is located in the rear compartment on the driver's side.
Page 377: If A Tire Goes Flat
Your air inflator will automatically shut off after about 10 minutes. The light in the switch will blink. After about one minute you can use the system again. Press the inflator switch and the indicator light will come on. Notice: Don’t run your air inflator for longer than 30 minutes at one time.
Page 378: Changing A Flat Tire
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flasbrs. Changin, tire can cause an injury. The vehicle can slip off the jack and roll over you or other people.
Page 379 Removing the Spare Tire and Tools The equipment you’ll need is located in the storage compartment at the rear of the vehicle, on the passenger’s side. 1. Open the jack storage compartment by lifting up the tab and pulling the cover off. A.
Page 380 Removing the Spare Tire (Vehicles without the Rear Convenience Center) The compact spare tire is located under the vehicle, ahead of the rear bumper. Use the spare tire hoist to raise, lower and store the compact spare tire. See Compact Spare Tire on page 5-85 for more information about the compact spare.
Page 381 To continue changing the flat tire see “Removing the Flat Tire and Installing the Spare Tire” later in this section. If the spare tire will not lower, the secondary latch may be engaged causing the tire not to lower. Do the following to check the cable: 1.
Page 382 A. Rear Convenience D. Hoist Shaft E. Compact Spare Tire Center Retainer Folding Wrench G. Hoist Shaft Assembly C. Storage Compartment Cap Hole 1. Open the storage compartment door of the convenience center that is nearest the liftgate and remove the cap on the bottom of the storage compartment.
Page 383 To continue changing the flat tire see “Removing the Flat Tire and Installing the Spare Tire” later in this section. If the spare tire will not lower, the secondary latch may be engaged causing the tire not to lower. Do the following to check the cable: 1.
Page 384 beginning this x e d u r e read all the instructions. Failure to read and follow the instructions could damage the hoist assembly and you and others could get hurt. Read and follow the instructions listed below. To release the spare tire from the secondary latch, do the followinl- Someone standing toG Jose during the procedure could be injured by the jack.
Page 385 5. Turn the folding wrench clockwise to raise the jack until it lifts the secondary latch spring. 6. Keep raising the jack until the spare tire stops moving upward and is held firmly in place, this lets you know that the secondary latch has released.
Page 386 8. Grasp the spare tire with both hands and pull it out from under the vehicle. 9. Reach under the vehicle and remove the folding wrench and jack. 10. When the spare tire has been completely lowered, tilt the retainer and slip it through the wheel opening.
Page 387 Notice: To help avoid damage to lock lock key, do not use an impact wrench with 3. Near each wheel, there is a notch in the vehicle’s body. Position the jack and raise the jack head until it fits firmly into the notch in the vehicle’s frame nearest the flat tire.
Page 388 4. Attach the folding wrench to the jack, and turn the wrench clockwise to raise the jack head 3 inches (7.6 cm). 5. Raise the vehicle by turning the folding wrench clockwise in the jack. Raise the vehicle far enough off the ground so that there is enough morn for the spare tire to fit under the wheel well.
Page 389 9. Lower the vehicle by attaching the folding wrench to the jack and turning the wrench counterclockwise. Lower the jack completely. 10. Tighten the wheel nuts firmly in a crisscross sequence, as shown. 5-78 Incorrect wheel nuts or improperly wheel nuts can cause the wheel to become loose and even come off.
Page 390 ng a Flat or Bare Tire anc - . I Storing a jack, a tire or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
Page 391 Attach the folding wrench to the hoist shaft. Turn the folding wrench clockwise to lift the spare tire. When the tire reaches the stabilizer bar, move the tire over the bar, then continue to turn the folding wrench clockwise to lift the spare tire. When the tire is almost in the stored position, turn the tire so that the valve stem is towards the rear of the vehicle.
Page 392 Put back all tools as they were stored in the jack storage compartment and put the compartment cover back on. To put the cover back on, slip the tabs on the side 01 the cover into the cover opening. Push the cover in place and push down the tabs on the cover so that it rests in the groove.
Page 393 1. Flip up the D-ring located in the rear cargo area. 2. Lay the tire in the rear cargo area of the vehicle with the valve stem up with the center hole of the tire over the D-ring. For vehicles with aluminum wheels, remove the center cap by tapping the back of the cap with the folding wrench.
Page 394 1. Open the center storage compartment door of the rear convenience center. 2. Remove the cap on the bottom of the storage compartment and flip the D-ring up. 3. Lay the tire on top of the center storage compartment with the valve stem down. Make sure you can see the D-ring through the center hole of the tire.
Page 395 3. Flip the D-ring so it is pointing outward. 4. Open the convenience center cover. 5. Stand the full-size tire up, in the tray against the back of the seat with the valve stem pointing out. 6. Remove the J-hook and the wing nut from the back the jack access door.
Page 396: Compact Spare Tire
3. Remove the J-hook and the wing nut from the back of the jack access door. Assemble the wing nut and the J-hook. 4. Install the wing nut and the J-hook to the D-ring through the center hole of the tire. 5.
Page 397 Notice: When the compact spare is installed, don’t take your vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails. That can damage the tire and wheel, and maybe other parts of your vehicle. Don’t use your compact spare on other vehicles.
Page 398: Appearance Care
Appearance Care Remember, cleaning products can be hazardous. Some are toxic. Others can burst into flames if you strike a match or get them on a hot part dangerous if you breathe their fumes in a closed space. When you use anything from a container to clean your vehicle, be sure to follow the manufacturer’s warnings and instructions.
Page 399 Here are some cleaning tips: Always read the instructions on the cleaner label. Clean up stains as soon as you can they set. Carefully scrape off any excess stain. Use a clean cloth or sponge, and change to a clean area often.
Page 400 Vinyl Use warm water and a clean cloth. Rub with a clean, damp cloth to remove dirt. You may have to do this more than once. Things like tar, asphalt and shoe polish will stain if you don’t get them off quickly. Use a clean cloth and vinyl/leather cleaner.
Page 401: Care Of Safety Belts
Care of Safety Belts Keep belts clean and dry. Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Page 402 Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish. You can get GM-approved cleaning products from your dealer. See Vehicle Care/Appearance Materials on page 5-93. If your vehicle has a “basecoaf/clearcoat” paint finish. The clearcoat gives more depth and gloss to the colored basecoat.
Page 403: Sheet Metal Damage
The surface of these wheels is similar to the painted surface of your vehicle. Don’t use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because you could damage the surface. Do not use chrome polish on aluminum wheels.
Page 404: Chemical Paint Spotting
Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces your vehicle. This damage can take two forms; blotchy, ringlet-shaped discolorations, and small irregular dark spots etched into the paint surface.
Page 405 GM Vehicle Care/Appearance Materials (cont'd) Description Removes dirt, grime, Glass Cleaner smoke and fingerprints. Removes dirt and grime Chrome and Wire from chrome wheels and Cleaner wire wheel covers. Removes dust, fingerprints, and surface Finish Enhancer contaminants, Spray on wipe off. Removes swirl marks, fine scratches and other Swirl Remover Polish...
Page 406: Vehicle Identification
Vehicle Identification Vehicle Identification Number (VIN) This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panei, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Page 407: Electrical System
Electrical System Add-on Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 408 Floor Console Fuse Block The floor console fuse block is located to the left of the glove box near the floor. The fuses marked spare are available if a replacement - - - A - A IU5C 1 5 iGGUGU. Pull the door open to access the fuse block.
Page 409 Fuse Usage Turn Signal and Hazard Lamp Flashers Power Seats Turn Signal Switch and NSBU Switch 5-98 Fuse PASS-Keyw I I I Body Control Module (BCM) Accessory Relay Retained Accessory Diode Accessory Power Relay...
Page 411 Fuse Front Fog Lamps Ignition Relay, Neutral Start Switch, 5-1 00 Usage Automatic Transaxle Shift Lock Control System Spare Starter Solenoid Battery Fuse ABS Motor Spare Engine Cooling Fan Engine Cooling Fan Main Battery Fuse for Retained Accessory Power Relav and Accessojl Relay Main Battery Fuse for Heated Seats, Sware...
Page 412 Fuse Main Battery Fuse for Ignition Switch, Radio, Heads-Up Display, Remote Keyless Entry (RKE), Instrument Cluster, Air Conditioning and Bodv Computer Spare Spare Spare Spare Spare Spare Fuse Puller Diode for Air Conditioning E Z l Comtxessor Clutch Circuit Breaker Spare Usage Usage...
Page 413: Capacities And Specifications
Capacities and Specifications The following approximate capacities are given in English and metric conversions. Please refer to Part D: Recommended Fluids and Lubricants on page Application Air Conditioning Refrigerant (R134a) Automatic Transaxle Pan Removal and Replacement Complete Overhaul AWD Automatic Transaxle Pan Removal and Replacement Complete Overhaul Coolinq System with...
Page 414 Engine Specifications...
Page 415: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Windshield Wiper Blades 24.0 inches (60.0 cm) Driver’s Side Length 22.0 inches (55.0 cm) Passenger’s Side Length Shepherd’s Hook Type *ACDelco@ part number. 5-1 04...
Page 416 Section 6 Maintenance Schedule ... Introduction ... Your Vehicle and the Environment Maintenance Requirements ... How This Section is Organized ... Part A: Scheduled Maintenance Services Using Your Maintenance Schedule Scheduled Maintenance ... Part B: Owner Checks and Services At Each Fuel Fill ... At Least Once a Month ...
Page 417: Maintenance Schedule
Maintenance Schedule Introduction KEEP ENGINE AT THE PROPER - N E L AND CHANGE AS RECOMMENDED Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details.
Page 418: How This Section Is Organized
How This Section is Organized This maintenance schedule is divided into five parts: “Part A: Scheduled Maintenance Services” explains what to have done and how often. Some of these services can be complex, so unless you are technically qualified and have the necessary equipment, you should let your dealer’s service department or another qualified service center do these jobs.
Page 419: Part A: Scheduled Maintenance Services
Part A: Scheduled Maintenance Services This part contains engine oil and chassis lubrication scheduled maintenance which explains the engine oil life system and how indicates when engine oil and filter. Lubricate chassis components with each oil change. Also, listed are scheduled maintenance services which are to be performed at the mileage intervals specified.
Page 420 See Part 6: Owner Checks and Services on page 6-9 and Part C: Periodic Maintenance Inspections on page 6- 13. Footnotes f The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle 's useful life.
Page 421 7,500 Miles (1 500 km) Rotate tires. See Tire Inspection and Rotation on page 5-58 for proper rotation pattern and additional information. (See footnote @.) (See footnote 15,000 Miles 000 km) Inspect engine air cleaner filter if you are driving in dusty conditions.
Page 422 52,500 Miles (87 500 km) Ll Rotate tires. See Tire lnspection and Rotation on page 5-58 for proper rotation pattern and additional information. (See footnote @.) (See footnote +.) 60,000 Miles (100 000 km) 0 Rotate tires. See Tire lnspection and Rotation on page 5-58 for proper rotation pattern and additional information.
Page 423 100,000 Miles (166 000 km) Inspect spark plug wires. An Emission Control Service. 0 Replace spark plugs. An Emission Control Service. 0 Change automatic transaxle fluid and filter if the vehicle is mainly driven under one or more of these conditions: In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher.
Page 424: At Each Fuel Fill
Part B: Owner Checks and Services Listed in this part are owner checks and services which should be performed at the intervals specified to help ensure the safety, dependability and emission control performance of your vehicle. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to your vehicle, make sure they are the proper ones, as shown in Part D.
Page 425: At Least Twice A Year
At Least Twice a Year Restraint System Check Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Page 426 Starter Switch Chec When you are doing this cheek, the vehicle could move suddenly. If it does, you or others could be injured. Follow the steps below. 1. Before you start, be sure you have enough room around the vehicle. 2.
Page 427 Ignition Transaxle Lock Check While parked, and with the parking brake set, try to turn the ignition key to OFF in each shift lever position. The key should turn to OFF only when the shift lever is in PARK (P). The key should come out only in OFF.
Page 428: Part C: Periodic Maintenance
Part C: Periodic Maintenance Inspections Listed in this part are inspections and services which should be performed at least twice a year (for instance, each spring and fall). You should let your dealer’s service department or other qualified service center do these jobs.
Page 429: Throttle System Inspection
Throttle System Inspection Inspect the throttle system for interference or binding, and for damaged or missing parts. Replace parts as needed. Replace any components that have high effort or excessive wear. Do not lubricate accelerator and cruise control cables. Transfer Case (Power Transfer Unit) and Carrier Assembly-Diff erential (Rear Drive Module) All-Wheel Drive Inspection...
Page 430: Part D: Recommended Fluids And Lubricants
Part D: Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number or specification may be obtained from your dealer. Fluid/Lubricant Engine Oil Engine oil with the American Petroleum Institute Certified for Gasoline Engines starburst symbol of the proper viscosity. To determine the preferred viscosity for your vehicle's engine, see Engine Oil on page 5- 13.
Page 431: Part E: Maintenance Record
Part E: Maintenance Record After the scheduled services are performed, record the date, odometer reading and who performed the service and any additional information from “Owner Checks and Services” or “Periodic Maintenance” on the following record pages. Also, you should retain all maintenance receipts. Your owner information portfolio is a convenient place to store them. Maintenance Record 6-1 6...
Page 432 Maintenance Record (cont’d) 6-1 7...
Page 433 Maintenance Record (cont’d) 6-1 8...
Page 434: Customer Assistance Information
Section 7 Customer Assistance Information ... Customer Satisfaction Procedure Customer Assistance for Text Telephone (TTY) Users ... Customer Assistance Offices GM Mobility Program for Persons Disabilities ... Roadside Assistance Program ... Customer Assistance Information Courtesy Transportation Reporting Safety Defects to the United States Government ...
Page 435: Customer Assistance Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Buick. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 436: Customer Assistance For Text
To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Buick has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Buick by dialing: 1-800-83-BUICK. (TTY users in -860-263-3830.
Page 437: Customer Assistance Offices
Customer Assistance Off ices Buick encourages customers to call the toll-free number for assistance. If a U S . customer wishes Buick, the letter should be addressed to Buick’s Customer Assistance Center. United States Buick Customer Assistance Center P.O. Box 33136...
Page 438: Gm Mobility Program For Persons
1-800-GM-DRIVE (463-7483) for details. All TTY users call 1-800-263-3830. Roadside Assistance Program Buick Motor Division is proud to offer Buick Premium Roadside Assistance to customers for vehicles covered under the 3 year/36,000 mile (60 000 km) new car warranty (whichever occurs first).
Page 439: Courtesy Transportation
Vehicle Identification Number (VIN) Vehicle license plate number Buick reserves the right to limit services or reimbursement to an owner or driver when, in Buick’s judgement, the claims become excessive in frequency or type of occurrence. While we hope you never have the occasion to use our service, it is added security while traveling for you and your family.
Page 440 Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait Buick helps minimize your inconvenience by providing several transportation options. Depending on the circumstances,...
Page 441: Reporting Safety Defects To The United States Government
Additional Program Information Courtesy Transportation is available during the Bumper-to-Bumper warranty coverage period, but it is not part of the New Vehicle Limited Warranty. A separate booklet entitled Warranty and Owner Assistance Information furnished with each new vehicle provides detailed warranty coverage information. Courtesy Transportation is available only at participating dealers and all program options, such as shuttle service, may not be available at every dealer.
Page 442: Reporting Safety Defects To The
In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you’ll notify us. Please call us at 1-800-521 -7300, or write: Buick Customer Assistance Center P.O. Box 33136 Detroit, MI 48232-51 36 In Canada, please call us at 1-800-263-3777 (English) or 1-800-263-7854 (French).
Page 443 Owner’s Information Owner publications are written specifically for owners and intended to provide basic operational information about the vehicle. The owner’s manual will include the Maintenance Schedule for all models. In-Portfolio: Includes a Portfolio, Owner’s Manual, and Warranty Booklet. RETAIL SELL PRICE: $35.00 Without Portfolio: Owner’s Manual only.
Page 444 Supplement to the 2003 Pontiac Aztek and 2003 Buick Rendezvous Owner’s Manual This information replaces the Audio Speakers text for the “Entertainment System” on page Pontiac Aztek and page 3-103 for the 2003 Buick Rendezvous. Audio Speakers Audio from the DVD Player or auxiliary devices can...
Page 445 To turn the vehicle’s speakers on and the CD/AUX or the TAPE/CD button on the front audio system. The audio from the entertainment system can be heard through both the wireless headphones and the vehicle’s speakers at the same time. You can listen to the entertainment system through the wired headphone jacks on the RSA system when the following occurs:...
Page 446 About Driving Your Vehicle ... Accessory inflator ... Accessory Power Outlets Adding Washer Fluid ... 5-36 Additional Program Information ... Additives, Fuel ... Add-on Electrical Equipment ... Adjusting the Speakers (Balance/Fade) ... Air Bag Readiness Light Air Bag Systems ... How Does an Air Bag Restrain? Servicing Your Bag-Equipped Vehicie...
Page 447 Audio Systems (cont.) Rear Seat Audio (RSA) Setting the Time ... Theft-Deterrent Feature Understanding Radio Reception XMTM Satellite Radio Antenna System ... 3-1 I6 Auto Door LocWUnlock ... 3-63 Automatic Door LocWUnlock ... Automatic Headlamp System ... 4-36 Automatic Level Control Automatic Operation Automatic Transaxle Fluid ...
Page 448 Canceling the Rear Door Security Locks Capacities and Specifications ... 5-102 Captain Chairs, Rear Carbon Monoxide ... Care of Safety Belts ... Care Cassette Tape Player CD and DVD Player CDs and DVDs Cargo Lamp Carrier Assembly-Differential (Rear Drive Module) Cassette Deck Service Cassette Tape Messages ...
Page 449 Climate Control Dual Automatic Climate Control System Dual Outlet Adjustment ... Compact Disc Errors ... Compact Disc Messages Compact Spare Tire Compass Variance Content Theft-Deferrent Control of a Vehicle ... Convenience Center, Rear Convenience Net ... Coolant Engine Temperature Gage ... Engine Temperature Warning Message Heater, Engine ...
Page 450 Door (cont.) Programmable Automatic Door Locks Rear Security Locks ... Driver Four-Way Manual Seat Position, Safety Belt ... Driver Behavior ... Driver Information Center (DIC) ... DIC Controls and Displays ... DIC Vehicle Personalization ... Driving At Night ... City ... Defensive ...
Page 451 Engine (cont.) Coolant Heater ... Coolant Temperature Gage ... Coolant Temperature Warning Message Cooling System Inspection Engine Compartment Overview ... Exhaust ... Low Oil Level Message ... Oil ... Overheating ... Starting ... Engine Coolant Level Check ... Engine Oil Additives ... Engine Oil Level Check ...
Page 452 Front Reading Lamps Fuel ... Additives ... California Fuel ... Filling a Portable Fuel Container Filling Your Tank ... Fuels in Foreign Countries ... Gage ... Gasoline Octane Gasoline Specifications ... Low Warning Message System Inspection ... Fuses Fuses and Circuit Breakers ...
Page 453 Hood Checking Things Under ... Release ... Horn ... How the System Works ... How to Add Coolant to the Coolant Recovery Tank ... How to Add Coolant to the Radiator ... 5-32 How to Add Fluid ... How to Check ... How to Check Power Steering Fluid ...
Page 454 Key Lock Cylinders Service Keyless Entry System Keys ... Lamps Exterior Interior ... Lamps on Reminder ... Lap-Shoulder Belt ... LATCH System Chi!d Restraints ... Securing a Child Restraint Designed for the LATCH System ... Leather ... Leaving Your Vehicle ... Leaving Your Vehicle With the Engine Running Liftgate ...
Page 455 Maintenance. Normal Replacement Parts Maintenance Schedule At Each Fuel Fill ... At Least Once a Month ... At Least Once a Year ... 6-10 At Least Twice a Year ... Brake System Inspection ... Engine Cooling System Inspection ... 6-13 Exhaust System Inspection ...
Page 456 Message (cont.) Remote Keyless Entry Transmitter Battery Low Warning Service Traction System Warning Soon ... Service Vehicle Traction Active Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) ... Mirrors Automatic Dimming Rearview Manual Rearview Mirror Outside Convex Mirror Outside Curb View Assist Mirror Outside Heated Mirrors...
Page 457 Parking Assist ... Brake ... Over Things That Burn ... Parking Brake and Automatic Transaxle Park (P) Mechanism Check Parking on Hills ... Part A Scheduled Maintenance Services ..6-4 Part B Owner Checks and Services ... 6-9 Part C Periodic Maintenance Inspections ...
Page 458 Radios (cont.) Theft-Deterrent Understanding Reception ... RDS and DAB Messages RDS Messages Rear Hatch Ajar Warning Message Rear Reading Lamps Rear Safety Belt Comfort Guides Rear Seat Audio Rear Seat Operation ... Rear Seat Outside Passenger Positions Rear Seat Passengers, Safety Belts Rear Seat Radio Controls ...
Page 459 Restraint Systems Checking ... Replacing Parts ... Restraints, Head ... Retained Accessory Power (RAP) ... Retro-Active Reset ... Right Front Passenger Position, Safety Belts Roadside Assistance Program ... Rocking Your Vehicle To Get It Out ... 4-32 Roof Rack System ... Running Your Engine While You Are Parked ...
Page 460 Service ... Adding Equipment to the Outside of Your Vehicle Doing Your Own Work Engine Soon Light Publications Ordering Information Traction System Warning Message ... 3-47 Vehicle Soon Message Service Bulletins Service Engine Soon Light in the United States or Check Engine Light in Canada ... Service Manuals Setting Preset PTYs (RDS Only) Setting Preset Stations ...
Page 461 Tachometer ... Taillamps Back-up Lamps ... Turn Signal, and Stoplamps TCS Warning Light ... Theft-Deterrent, Radio ... Theft-Deterrent Systems ... Content Theft-Deterrent PASS-Key@ Ill I l l PASS-Key@ Operation ... Throttle System Inspection ... Tilt Mirror ... Tilt Wheel ... Tips and Trouble ...
Page 462 Turn and Lane-Change Signals ... Turn Signal/Multifunction Lever Turn Signals When Towing a Trailer Underbody Flushing Service Underhood Fuse Block Understanding Radio Reception ... Uniform Tire Quality Grading States United Unlock Feedback Used Replacement Wheels Using Cleaner on Fabric Using HomeLink@ ... Using RDS Using Song List Mode Ustrasonic Rear Parking Assist (URPA)
Page 463 Washer Fluid Low Warning Message Washing Your Vehicle Weatherstrip Lubrication Weight of the Trailer Weight of the Trailer Tongue What Kind of Engine Oil to Use What to with Used Oil What to Use Wheels Alignment and Tire Balance Replacement When to Add Engine Oil When to Change Engine Oil (GM Oil Life System) ...
Page 465 NOTES...

Buick 2003 Rendezvous Owner's Manual

Seats and Restraint Systems

Section 2 Features and Controls

Instrument Panel Section 3

Section Driving Your Vehicle

Section 5 Service and Appearance Care

Section 6 Maintenance Schedule

Quick Links

Chapters

Related Manuals for Buick 2003 Rendezvous

Summary of Contents for Buick 2003 Rendezvous