Sony APR-5001 Series Operation And Maintenance Manual page 50

APR
-
5003 V
WIND modes . To enter RECORD from the PLAY mode ,
it is necessary only
to press
nets
are
in
RECORD READY ( all channels in SAFE )
the
transport will not enter RECORD mode
.
4.2
.
1
Key and Display Functions
. If no chan -
RECORD
( REWIND )
causes
the transport to
go
Pressing
into fast rewind mode
.
This operation cancels any Once the transport is in RECORD mode
,
the recording
status of any channel
can be changed by first press -
ing the channel ' s RECORD
paragraph 4.4
. 1
—
RECORD section ) , and then press -
. For
instance
,
let it be assumed that the
transport has been set into RECORD with only Chan
-
nel 1 actually recording
. Channel 2
can
be set into
RECORD at any
time by
simply pressing the CH
2
key
, and
then pressing
Conversely
, given the
same
situation
, Channel i can
be taken out of RECORD by pressing CH 1
and then pressing
previous motion command such as FAST FORWARD
,
PLAY or RECORD
,
Except when used in conjunction
with SHIELD DEFEAT ,
channels to be muted .
key (
see
READY
also
causes the audio
mg
RECORD
Touching the
causes the transport to enter SPOOL mode . In this
mode
,
the wind speed
is
reduced to
about
75 ips ( in -
ches per second ) so as to
allow
more
uniform packing
of the tape
.
control during
FAST REWIND
RECORD
R E A D Y
READY
RECORD
Pressing 1331
( FAST FORWARD
)
causes the transport
to enter the FAST FORWARD mode
,
this overriding
any previously selected motion command such as RE -
WIND , PLAY or RECORD
.
Except when used in con -
junction with SHIELD DEFEAT , B also causes the
audio channels to be muted
.
SgliS
This key is used to set the desired PLAY speed
.
Each
time the key is pressed the speed advances to the next
higher speed
,
which then is shown on the HIGH
,
MID
,
or LOW TAPE SPEED indicator
.
The range of these
speeds is set by the headstack identification code
.
At
machine power - up , the most recently used speed will
be automatically selected
.
As with
REWIND
mode
,
touching the
during FAST REWIND causes the transport to enter
SPOOL mode
.
control
wm
(
LIFTER DEFEAT ) causes the
Pressing
lifters to be defeated
,
allowing them to remain
mam
cancels any previously selected mo -
Pressing
lion command and stops the tape
.
This causes the
disengaged when
in any FAST WIND mode ,
i
. e
.
FAST
FORWARD , REWIND , LOCATE or SPOOL
.
key to illuminate ( so
long
as there is tape
across the End of Tape sensor
)
.
The audio channels
will be muted unless either
LIFTER DEFEAT or
SHIELD DEFEAT is selected
.
(
SHIELD DEFEAT )
key is
used to deac -
The
tivate the
shields
. When this key is pressed , it il -
luminates
to
indicate that the shield will stay down
during
PLAY or RECORD
,
and that the audio chan -
nels will stay unmuted
.
SHIELD
initiates the PLAY mode ,
causing the Pressing
tape
to shuttle across the heads at the selected play
speed
.
also is used to trigger RESOLVE ON
PLAY operation ( paragraph 4.5
.
1 ) , to manually trig -
ger PREVIEW
/ EDIT / REVIEW operations , or to exit the
RECORD operation
.
ill *
!
The
EDIT
mode is used to facilitate the splicing and
edit - assembly operations
, and offers two different
methods , as follows :
Unless SHIELD DEFEAT is selected
,
the audio chan -
nels
are muted during the period between start - up
and the time that play speed is achieved
.
EDIT
—
In EDIT , all tape tensions
are relaxed , mak -
ing
it possible to use the splicing block .
DUMP EDIT
—
In
this mode
, the tape is played
across the heads , but the take - up reel is turned off
so that the tape runs off the machine into
a
suitable waste container
.
together with
sets those
Pressing
channels that are in RECORD READY
(
see paragraph
4.4
.
1
—
RECORD section
) into RECORD
Mode
,
which
can be entered from the STOP , FAST FORWARD or RE -
liii
Page 4 - 2