Sony APR-5001 Series Operation And Maintenance Manual page 158

5
-
3.4 Monitoring During Record Preset
Play
,
When the transport comes to
a full stop ,
then it will
enter
Play mode
.
During RECORD mode the user
may select the
monitor
source as either being the INPUT
signal which
is being recorded ( press
REPRO signal which Is derived from the Reproduce
head playing back the signal which has just been
recorded ( press
delayed from
the INPUT
signal
( by the distance be -
tween the heads divided by the Play speed ) .
STEP 2 If desired , set the output level of the
.
It will
illuminate to indicate that the output level
will now be set by the vernier control
.
Set
the vernier control to the desired volume
level
.
The panel meter will indicate the
level of the output
.
APR - 5000
.
Press OUTPUT ) or the
INPUT
or
UNCAL SYNC
)
.
The REPRO
signal will be
REPRO
5.5 RECORD PUNCH
-
IN
When it is desired to add a channel referenced to an
existing channel
.
In the example
, we
will attempt to
append the
material on one track (
TK 1 ) for ten seconds in the mid
-
dle of
a program .
Track 2 will remain in PLAY mode
and will not be changed during this operation .
o
z
,
—
ALN
—
SELECTED BIAS
© ©
RECORD
-
READY
MONITOR
REPRO SYNC INPUT
,
^
2
EEF
O
SELECT
i
ONE
ERASE ©
STEP 1 Connect the track 1 IN connector to
the ap
-
propriate audio
source
.
This
source
will pro -
vide the audio material which will be ap
-
pended into the
program .
8 !
©
o
r
RECORD LEVEL
UNCAL
r OUTPUT LEVEL
-
\
UNCAL
o
0
STEP 2 Connect the track 1 and track 2 OUT con -
nectors to the desired audio
monitoring
source .
During the punch - in period
,
track
1
will be live ( it may be desired
to mute or
attenuate the
signal during the punch
-
in
period
)
.
Figure 5
-
8
.
Meter Housing
—
Monitoring
During Record
5.4 PLAYBACK
STEP 3 Put track 1 in RECORD READY mode by
pressing the button
.
READY
5.4
.
1
Preparation
STEP 4 Put track 2 in SAFE mode . Ensure
that the
button is not illuminated .
If it is
illuminated
,
press the RECORD
button and will extinguish .
STEP 5 Place both channels in
SYNC
mode by
pressing the
STEP 1 Connect the audio output ( OUT ) connectors
of the APR - 5000
to the line
input
connec
-
tors of the desired
mixing console
or audio
amplifier
.
READY
READY
buttons
.
SYNC
STEP 2 Turn the power switch to ON
.
Set the audio
channels for the desired playback
source .
This will be either the Repro head
)
or
the Record head (
The Repro head will give better frequency
response
.
STEP 6 Locate the section of the
program to
be ap -
pended
.
Wind to a point several seconds
before the time the desired recording will
begin ( the punch
-
in point )
.
)
.
(
REPRO
SYNC
button
.
The transport
will enter PLAY mode and the
program
material will be heard
through the audio
monitor
.
STEP 7 Press
the
PLAY
5.4
.
2 To Start Playback
STEP 1 Press the
button
. It
will illuminate
to indicate that Play mode has been
selected
.
If the transport is not in STOP
mode
,
the
luminate to indicate that the transport is in
PLAY
STEP 8 At the appropriate time in the
program ,
button
.
Track 2 will button will also il -
press the
enter the RECORD mode and the BIAS and
STOP
RECORD
5 - 6