Table of Contents
Related Manuals for Invacare Aquatec Marine
Summary of Contents for Invacare Aquatec Marine
- Page 1 Aquatec® Marine en Bath lift User Manual ....... 3 This manual MUST be given to the user of the product. BEFORE using this product, read this manual and save for future reference.
-
Page 2: Table Of Contents
Contents 7 After Use ........23 7.1 Storage . -
Page 3: General
Aquatec® Marine 1 General This product complies with the directive 93/42/EEC for medical products. The launch date for this product is specified in the CE 1.1 Information about the user manual declaration of conformity. This user manual contains important information about the Manufacturer handling of the product. -
Page 4: Intended Use
Invacare® is continuously working towards ensuring that the company’s impact on the environment, locally and globally, Contraindications is reduced to a minimum. -
Page 5: Safety
– Check all parts for shipping damage and other damage or other conspicuous features. equipment. Invacare product manuals are available on the internet or at your local dealer (Addresses are displayed on the back cover of 2.2 Safety information on electromagnetic... -
Page 6: Labels And Symbols On The Product
2 minutes continuous use accord. followed by a 18 minute break – Switch off the external device and/or your Invacare® product if you notice such behavior. Note (disposal) – If other electrically operated medical products Type of protection cause a interference or are themselves disrupted, switch off your Invacare®... - Page 7 Aquatec® Marine The identification label is applied to the back of the backrest.
-
Page 8: Setup
Setup Seat 3 Setup 3.1 Safety information IMPORTANT! – Check the parts for transport damage before commissioning and contact the dealer if required. – Ensure during assembly that the parts are positioned correctly with respect to one another. 3.2 Scope of delivery A seat and backrest cover is optionally available. -
Page 9: Setting Up The Bath Lift
Aquatec® Marine Backrest Battery and charger Battery Charger Hand control with spiral cable Drive 3.3 Setting up the bath lift Plate, backrest WARNING! Spindle foot Risk of slipping! The bath lift can slip if the suction cups do not have a proper hold. –... - Page 10 Setup 27.3"- 28.8" WARNING! Tub width Risk of injury and damage! (outside) – Only set up the bath lift in bathtubs that ≤ 16.3" Tub height comply with the specifications of the following (inside) table. – Only use the bath lift in bathtubs with frontal overflows.
- Page 11 Aquatec® Marine 1. Place the seat B on the bottom of the empty bathtub. Ensure that the spindle foot retainer C is pointing towards the end of the bathtub opposite the drain A. 3. Place the backrest A (without the battery) onto the seat so that the hooks B of the backrest fit into the hinges C of the seat plate D.
-
Page 12: Charging The Battery
Setup 4. Hold the backrest at the center of the head end and WARNING! carefully lift it into the end position. Risk of electric shock – Only recharge the battery in dry rooms at room temperature (15 °C to 25 °C) and never in the bathroom. - Page 13 Aquatec® Marine The charging indicator B lights red while the battery is charging and changes to green when charging is finished. It is not possible to overcharge the battery. 3. Disconnect the charger from the power socket. 4. Pull the jack plug of the charger out of the jack socket of the battery.
-
Page 14: Usage
Usage 4 Usage IMPORTANT! – Recharge the battery completely before each use, 3.4 Charging the battery, page 13. 4.1 Safety information 1. Refer to operating conditions in section 9.4 CAUTION! Environmental Parameters, page 27. Overloading the bath lift can lead to damage to the device or prevent lifting. - Page 15 Aquatec® Marine Lowering the bath lift IMPORTANT! Risk of damage IMPORTANT! – The hand control may only be used when the If the seat is already lowered, the backrest lowers backrest is properly installed and in the upright towards the rear. position.
-
Page 16: Bathing
Usage 4.3 Bathing 1. Press and hold the Up button C on the hand control until the seat is level with the edge of the bathtub. WARNING! 2. Make sure that the side flaps are level with the seat Risk of slipping! plate and rest flat on the edge of the bathtub (initial The bath lift can slip if the suction cups do not position). - Page 17 Aquatec® Marine IMPORTANT! – Remove the battery when not used constantly.
-
Page 18: Transport
Transport 5.2 Removing the bath lift 5 Transport 1. Let the water out of the bathtub. 5.1 Safety information 2. Lower the bath lift using the Down button until the backrest stops in the lowered end position, see 4.2 CAUTION! Controlling the bath lift, page 15. - Page 19 Aquatec® Marine 4. Hold the backrest at the head end with one hand and 6. Fold the side flaps of the seat inwards. slowly fold the backrest all the way forward. IMPORTANT! Risk of damage – When folding the backrest down, ensure that the spiral cable of the hand control does not get caught.
-
Page 20: Maintenance
Maintenance 6 Maintenance IMPORTANT! All cleaning agents and disinfectants used must be effective, compatible with one another and 6.1 Maintenance and servicing must protect the materials they are used to clean. – For further information on decontamination If the above cleaning and safety notices are observed, the in Health care Environments, please refer product will be maintenance free. - Page 21 Aquatec® Marine Cleaning the covers (optional) 1. Unbutton the covers from the seat and backrest. 2. Wash the covers in a washing machine at max. 140°F using a mild detergent. IMPORTANT! Risk of damage – Washing at high temperatures can cause shrinkage.
-
Page 22: After Use
After Use Return such batteries to your retailer or to your municipal 7 After Use collection point. Returning them is free of charge and is required by law. 7.1 Storage Only throw discharged batteries into the containers provided. IMPORTANT! Risk of damage –... -
Page 23: Troubleshooting
Aquatec® Marine 8 Troubleshooting 8.1 Identifying and repairing faults The following table provides information on malfunctions and their possible causes. If you cannot correct the malfunction using the remedies named, contact your dealer directly. Fault Possible cause Remedy No motor noise audible/lift Jack socket of the hand Lock the jack socket. -
Page 24: Technical Data
Technical data 9.2 Electronic data 9 Technical data Battery operating 12 V DC / 3 Ah 9.1 Dimensions and weight voltage 34.7" 48 VA Rated input power Total length at lowest position 24.5" Rated current Total length at highest position 41.3"... - Page 25 Aquatec® Marine Dust-proof and protected against the penetration of water during temporary immersion. Protected against the penetration of water that splashes from any direction against the housing.
-
Page 26: Materials
Technical data 9.3 Materials PPGF Backrest PPGF Seatplate Covers All materials used are corrosion resistant and latex free. 9.4 Environmental Parameters Operating conditions 10 - 40 °C Ambient temperature Relative humidity 15 % - 93 %, non-condensing Atmospheric pressure 795 - 1060 hPa Storage and shipping conditions Ambient temperature 0 - 40 °C... - Page 27 All rights reserved. Republication, duplication or modification in whole or in part is prohibited without prior written permission from Invacare. Trademarks are identified by ™and ®. All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted.
- Page 28 Distributors: USA: Clarke Health Care Products 7830 Steubenville Pike Oakdale, PA 15071, USA Toll Free: (888) 347-4537 Fax: (724) 695-2922 email: info@clarkehealthcare.com www.clarkehealthcare.com Aquatec Operations GmbH Alemannenstrasse 10 D-88316 Isny Germany CHP74...