Center control panel pack for sony mks-9011; sony mks-9012; sony mks-8011; sony mks-8031tb; sony mks-8032; sony mks-8033; sony mks-8035; sony mks-8041; sony mks-8075; sony swc-5002; sony swc-5005; sony swc-5010 (40 pages)
Summary of Contents for Sony HKC-7081
Page 1
CCD MODIFICATION UNIT HKC-7081 INSTALLATION AND MAINTENANCE MANUAL 1st Edition (Revised 1)
Page 2
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
Page 3
Manual Structure Purpose of this manual ..................5 (E) Contents ....................... 5 (E) Related manuals ....................6 (E) 1. Installation 1-1. Configuration of HKC-7081 ..............1-1 (E) 1-2. Installation Procedures ................1-1 (E) 1-3. Replacing CCD Unit ................1-1 (E) 1-3-1. Description on CCD Block Number ........1-1 (E) 1-3-2.
Page 7
Describes the components that constitute the unit and the procedures to install the HKC-7081 in the HD color camera HDC-750. Section 2 Electrical Alignment Describes electrical adjustment necessary after the HKC-7081 is installed in the HDC-750. Section 3 Setup Menu Describes the setup menu for the modified HDC-750.
Page 8
When servicing the modified camera, see the HKC-7081 installation and maintenance manual and HDC-750 maintenance manual together.
Page 9
Section 1 Installation The HKC-7081 is the modification unit for the HDC-750. By installing the HKC-7081 in the HDC-750, it can be obtained for the HD signal having 1920 x 1080 effective picture elements. To install proceed as follows. 1-1. Configuration of HKC-7081 Description Q’ty...
Page 10
Prior to replacement, be sure to disconnect the optical cable or the cable connected at the DC IN connec- tor in addition to turning off the power switch. 1. Remove the three screws, then remove the transportation holder from the HKC-7081. Transportation holder...
Page 11
6. Remove the four bolts to remove the front panel from the CCD unit. Fixture: Allen wrench (width across flat = 2.5 mm) Bolts (M3 x 8) Setscrews (WP2 x 3) Setscrews (WP2 x 3 Front panel Bolts (M3 x 8) ND filter knob CC filter knob 1-3 (E) HKC-7081...
Page 12
K3 x 6 B2.6 x 4 8. Install the filter disk unit to the HKC-7081 with the two screws which were removed in procedure 4. Connect the connector from the filter disk unit to the driver board. . Be very careful not to touch the surface of the filter disk unit when installing the HKC-7081.
Page 13
1. Slide portions A in the direction of the arrow and insert the flexible card wire as far as it will go with the conductive surface down. 2. Slide portions A in the reverse direction to lock. Conductive surface 1-5 (E) HKC-7081...
Page 14
5. Align the ND filter knob number 1 with the mark on the front panel and tighten the two setscrews. Tightening torque: 20 x 10 N.m (2.0 kgf.cm) 6. Rotate the ND filter knob and check that it moves smoothly. Setscrews (WP2 x 3) Setscrews (WP2 x 3) Mark 1-6 (E) HKC-7081...
Page 15
1-4-1. Modifying VDA-31 Board (Camera Adaptor) Parts Required Prepare the following resistors because they are not supplied with the unit. Description Q’ty Sony Part No. Res, metal chip 15 Z 1-218-648-11 Res, metal chip 18Z 1-218-650-11 Res, metal chip 30 Z...
Page 16
1. Remove the VA-158 board. 2. Solder the jumper wires from the modification board to the positions specified by the figure. 3. Stick the modification board on the VA-158 board with Sony bond as shown in the figure. (Shaded portions) 4.
Page 17
Sony Part No. 7-432-912-52 Modification Procedures 1. Remove the IF-569 board. 2. Solder the jumper wire between pin 119 of IC100 and pin 16 of IC36. 3. Stick the jumper wire with Sony bond as shown in the figure. (Shaded portion) IC100 IC36...
Page 18
Modification Procedures 1. Remove the SG-226 board. 2. Solder the jumper wire between pin 119 of IC65 and pin 36 of IC71. 3. Stick the jumper wire with Sony bond as shown in the figure. (Shaded portion) IC65 TO Pin 36/IC71...
Page 19
Electrical Alignment 2-1-2. Switch Setting of IF-569 Board This section explains adjustment items required after the HKC-7081 is installed. Perform the following adjustments with setup menu. 1. Turn off the power, then remove the IF-569 board. Regarding the setup menu operation, refer to Section 3.
Page 20
(Select the file in accordance with the lens attached. If there is no appropriate file, select NO OFFSET, then change the name of lens with MSU.) 10uS Resetting after Adjustment . Return the switches to their previous positions. 2-2 (E) HKC-7081...
Page 21
Adjust for B-ch in the same manner. 7. Adjust the white balance. WHITE button/MSU-700 → ON (lit) Lens File Store MSU menu operation: . FILE button → ON (lit) . Touch panel operation [Lens|File] → [Lens|Store] → [Store] 2-3 (E) HKC-7081...
Page 22
OHB File Store 1. MSU menu operation: . FILE button → ON (lit) . Touch panel operation [OHB|File] → [OHB|Store] → [Store] 2. When the store operation is complete, the message “OHB File Stored” is displayed. 2-4 (E) HKC-7081...
Page 23
ITEM: ND OFST Store → Disable new reference file. Storing the reference file Perform the following operation with setup menu. MENU: File PAGE: Reference File ITEM: Store File (Press the MENU SEL switch to store the reference file.) 2-5 (E) HKC-7081...
Page 24
Perform readjustment according as necessity, then store a new operator file. Storing the operator file Perform the following operation with setup menu. MENU: Operation PAGE: Operator File ITEM: Store (Press the MENU SEL switch to store the operator file.) 2-6 (E) HKC-7081...
Page 25
SYS Config (On) (Off) (On) ..Equipment required Camera Adaptor HDCA-750A Viewfinder HDVF-20 ( or monochrome monitor) Supply power from a camera control unit HDCU-700A or AC adaptor AC-550/550CE to the camera adaptor. 3-1 (E) HKC-7081...
Page 26
In this section, an item under “Ver.” in the table shows a ROM version. If any version is given, it shows that the function for the item is added or changed, and the ROM with that version or higher version supports the function, If no version is given, it shows that every ROM version supports the function. 3-2 (E) HKC-7081...
Page 27
The lens extender is in use [On], Off Fan: Fan mode is at “Off” (forcibly off) [On], Off 60Hz 60Hz: Field frequency is set at 60 Hz [On], Off Optical Optical: “Optical” showing a photo-receptive condition indicates anything but “GRN” 3-3 (E) HKC-7081...
Page 28
Turns on and off the zebra pattern display [70], 90, 70&90 % Selects the zebra pattern [16:9], 4:3, Squeeze VF Scan Selects the VF scan mode Setting Screen Setting 16 : 9 4 : 3 Squeeze Screen Object Object Object 3-4 (E) HKC-7081...
Page 29
LINE MIC2 (of camera adaptor) LINE MIC (of camera) MIC2 (of camera adaptor) MIC (of camera) MIC2 (of camera adaptor) LINE MIC2 (of camera adaptor) AES/EBU Setting Screen Auto-iris window frame is shown in a shaded pattern 3-5 (E) HKC-7081...
Page 30
Press MENU SEL switch Recalls the user’s operator file to execute Store Press MENU SEL switch Stores the user’s operator file to execute Preset Press MENU SEL switch Returns the operator file items to their preset values to execute 3-6 (E) HKC-7081...
Page 31
Press MENU SEL switch Resets numeric settings on the Gamma page to 0 to execute (When you press MENU SEL switch, the “Clear” indication flashes. Press MENU SEL switch again to execute; press CANCEL button to cancel) 3-7 (E) HKC-7081...
Page 32
Press MENU SEL switch Resets numeric settings on the Detail 1 page to 0 to execute (When you press MENU SEL switch, the “Clear” indication flashes. Press MENU SEL switch again to execute; press CANCEL button to cancel) 3-8 (E) HKC-7081...
Page 33
Press MENU SEL switch Resets numeric settings on the Matrix page to 0 to execute (When you press MENU SEL switch, the “Clear” indication flashes. Press MENU SEL switch again to execute; press CANCEL button to cancel) 3-9 (E) HKC-7081...
Page 34
. Every time MENU SEL switch is pressed, the scene file replaces the current settings . When the scene file is recalled, an asterisk appears next to the number Standard Returns the current amount of paint adjustments and switch setting to their reference values 3-10 (E) HKC-7081...
Page 35
CANCEL button to cancel) e) When executing the Auto Level, paint data is temporarily cleared and the automatic level adjustment is performed in sequence. After the adjustment is complete, adjustment result is stored as a master setup data. 3-11 (E) HKC-7081...
Page 36
If “RED” is indicated, be sure to clean the optical connector or optical connector cable. If “YEW” is indicated, cleaning them is recommended. For details on how to clean, refer to the maintenance manual supplied with the camera adaptor. 3-12 (E) HKC-7081...
Page 37
The standard values are stored at the factory ND OFST Clear Press MENU SEL switch Clears the white offset value for the ND filter to execute Setting Screen Auto-iris window frame is shown in a shaded pattern 3-13 (E) HKC-7081...
Page 38
Shifts vertically the location of the center marker on the screen 20 (down) ↔ _20 (up) Center POS Store Press MENU SEL switch Stores the location of the center marker at present in the to execute selected lens file number 3-14 (E) HKC-7081...
Page 39
Checks whether the video signals are properly output at pin 6 of IC106,IC206 and IC306 each, or not Checks the voltage at +5 V regulated line AU-203 DAP-5 Checks the audio clocks (13.5 MHz) at pin 43 of IC2 3-15 (E) HKC-7081...
Page 40
Turns on and off the function to activate the APR each time the black balance is automatically performed h) Rear tally lamp refers to back tally lamp (of HDCA-750A) and VF tally lamp (of HDVF-20 or HKCA-700). k) Front tally lamp refers to up tally lamp (of HKCA-700). 3-16 (E) HKC-7081...
Page 41
VF DISP switch is set to ON or OFF) Left, [Right] Zoom Disp Changes the indication location of the zoom position status displayed on the VF Left: Zoom position is located on the left Right: Zoom position is located on the right 3-17 (E) HKC-7081...
Page 43
Spare Parts 4-1. Notes on Repair Parts 1. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts commonality and improvement. Parts list has the present standardized repair parts.
Page 44
A-8273-217-A o MOUNTED CIRCUIT BOARD, DU-1 A-8273-219-A o MOUNTED CIRCUIT BOARD, PA-173 A-8320-951-A o MOUNTED CIRCUIT BOARD, DR-376 A-8320-952-A o MOUNTED CIRCUIT BOARD, NR-66 A-8320-953-A o MOUNTED CIRCUIT BOARD, RP-108 A-8320-954-A o MOUNTED CIRCUIT BOARD, TG-209 A-8320-780-A o MOUNTED CIRCUIT BOARD, CN-1674 HKC-7081...
Page 45
1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V 1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V 1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V 1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V 1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V 1-162-970-11 s CERAMIC, CHIP 0.01uF 10% 25V HKC-7081...
Page 46
8-729-120-21 s TRANSISTOR 2SD1614-T1XL 1-218-723-91 s METAL, CHIP 20K 0.50% 1/16W 1-218-716-11 s METAL, CHIP 10K 0.50% 1/16W 8-729-143-14 s TRANSISTOR 2SC4176-B35 1-218-723-91 s METAL, CHIP 20K 0.50% 1/16W 8-729-143-07 s TRANSISTOR 2SA1610-YY33 1-218-716-11 s METAL, CHIP 10K 0.50% 1/16W HKC-7081...
Page 47
1-218-716-11 s METAL, CHIP 10K 0.50% 1/16W R416 1-216-864-11 s METAL, CHIP 0 5% 1/16W R417 1-216-864-11 s METAL, CHIP 0 5% 1/16W ----------- NR-66 BOARD ----------- Ref. No. or Q'ty Part No. SP Description A-8320-952-A o MOUNTED CIRCUIT BOARD, NR-66 HKC-7081...
Page 48
1-135-149-21 s TANTALUM, CHIP 2.2uF 10% 10V 1-568-338-11 s CONNECTOR, BOARD TO BOARD 24P 1-568-361-21 s CONNECTOR, BOARD TO BOARD 24P 1-135-149-21 s TANTALUM, CHIP 2.2uF 10% 10V 1-135-149-21 s TANTALUM, CHIP 2.2uF 10% 10V 1-569-607-21 o CONNECTOR, BOARD TO BOARD 24P HKC-7081...
Page 49
1-218-661-11 s METAL, CHIP 51 0.50% 1/16W 1-218-737-11 s METAL, CHIP 75K 0.50% 1/16W 1-218-661-11 s METAL, CHIP 51 0.50% 1/16W 1-218-737-11 s METAL, CHIP 75K 0.50% 1/16W 1-218-699-11 s METAL, CHIP 2K 0.50% 1/16W 1-218-737-11 s METAL, CHIP 75K 0.50% 1/16W HKC-7081...
Page 50
1-241-833-11 s RES, ADJ, METAL 10K R132 1-218-740-11 s METAL, CHIP 100K 0.50% 1/16W R133 1-216-789-11 s METAL, CHIP 2.2 5% 1/16W RV303 1-241-833-11 s RES, ADJ, METAL 10K R134 1-216-789-11 s METAL, CHIP 2.2 5% 1/16W RV304 1-241-833-11 s RES, ADJ, METAL 10K HKC-7081...
Page 51
1-415-887-11 s DELAY LINE 1-415-890-11 s DELAY LINE 8-759-173-16 s IC TL062CPW 8-759-166-02 s IC UPC814G2 8-759-195-81 s IC TC7S86FU 8-759-195-81 s IC TC7S86FU 8-759-185-42 s IC LM4040AIM3-2.5 8-759-565-12 s IC CXD9086R 8-759-271-86 s IC TC7SH04FU 8-759-196-96 s IC TC7SH08FU-TE85R HKC-7081...
Page 52
1-218-723-91 s METAL, CHIP 20K 0.50% 1/16W 1-218-716-11 s METAL, CHIP 10K 0.50% 1/16W 1-218-716-11 s METAL, CHIP 10K 0.50% 1/16W 1-218-668-11 s METAL, CHIP 100 0.50% 1/16W 1-216-864-11 s METAL, CHIP 0 5% 1/16W 1-216-864-11 s METAL, CHIP 0 5% 1/16W 4-10 HKC-7081...
Page 61
: HIGH LEVEL : LOW LEVEL : HIGH LEVEL : DON’T CARE TC7S08FU(TE85R) (TOSHIBA) TC7SH08FU-TE85R (TOSHIBA) C-MOS 2-INPUT AND GATE —TOP VIEW— Y = A • B = A + B GND 3 0 : LOW LEVEL 1 : HIGH LEVEL HKC-7081...
Page 62
DUAL OPERATIONAL AMPLIFIERS (DUAL-SUPPLY TYPE) —TOP VIEW— X24C02S-3.0-C7000 (XICOR)(2K-BIT) X24C02S-T1 C-MOS SERIAL EEPROM —TOP VIEW— INPUT A0 - A2 : ADDRESS : SERIAL CLOCK : WRITE CONTROL INPUT/OUTPUT : SERIAL DATA NOTE : TYPE PIN 7 NM24C16 X24C02 X24C04 TEST 5-10 HKC-7081...
Page 66
+3.3 V +3.3 V REF. V REG. Q7, 8 _37M OUT _5.5 V 37N/XST2 DR, 5-11 DR, 5-4 _5.5 V _5.5 V _5.5 V SLOW SCAN ON OPB PLS DR, 5-7 VL IN VL OUT DR, 5-3 TG-209 HKC-7081 HDC700A-TG209-BLOCK/M HKC-7081...
Page 76
R9 51 G-PA GND R V COMP IN OPEN G V COMP IN 1.2k B V COMP IN 6.3V 0.01 R-PA OUT C301 R-PA GND IC4(3/4) 5.6k TL064CPW-E05 -5.5V 560k 0.022 2SA1611-T1M7 2SD1614-T1XL IC3(3/3) TC74HC4053AFT(EL OPEN 100k 100k IC4(4/4) TL064CPW-E05 HKC-7081...
Page 91
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any...