D-Link DES-1316 Manual
  1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Network Router
  5. DES-1316 - Switch
  6. Manual
D-Link DES-1316 Manual

D-Link DES-1316 Manual

Web-smart 8-port 10/100mbps ethernet switch with 8 10/100mbps 802.3af power over ethernet ports
Hide thumbs Also See for DES-1316:
Table of Contents

Advertisement

Quick Links

Download this manual
D-Link DES-1316
Web-Smart 8-Port 10/100Mbps Ethernet Switch with 8
10/100Mbps 802.3af Power Over Ethernet Ports
Manual
First edition
Building Networks for People

Advertisement

Table of Contents
loading

Related Manuals for D-Link DES-1316

Summary of Contents for D-Link DES-1316

  • Page 1 D-Link DES-1316 Web-Smart 8-Port 10/100Mbps Ethernet Switch with 8 10/100Mbps 802.3af Power Over Ethernet Ports Manual First edition Building Networks for People...
  • Page 2 FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 3 Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente domestico il prodotto può causare interferenze radio, nel cui caso è possibile che l`utente debba assumere provvedimenti adeguati. VCCI Warning BSMI Warning...

  • Page 4: Table Of Contents

    TABLE OF CONTENTS About This Guide... 6 Purpose ... 6 Terms/Usage ... 6 Introduction... 7 Fast Ethernet Technology ... 7 Switching Technology ... 7 VLAN (Virtual Local Area Network)... 8 Power over Ethernet (PoE) ... 9 Features... 9 Unpacking and Installation ... 11 Unpacking...
  • Page 5 Installing the Web Management Utility... 18 Discovery List... 20 Monitor List ... 21 Device Setting... 23 Toolbar... 25 Configuring the Switch ... 26 Login... 27 Setup Menu ... 30 Configuring Setup Setting... 31 Port Settings... 31 VLAN Settings (Virtual Local Area Network) ... 33 Trunk Setting ...

  • Page 6: About This Guide

    This guide discusses how to install your Web-Smart16-Port 10/100Mbps Ethernet Switch. Terms/Usage In this guide, the term “Switch” (first letter upper case) refers to your Web-Smart 8-Port 10/100Mbps Ethernet Web-Smart Switch with 8 10/100Mbps PoE ports and “switch” (first letter lower case) refers to...

  • Page 7: Introduction

    INTRODUCTION This chapter describes the features of the Web Smart Switch and some background information about Ethernet/Fast Ethernet switching technology. Fast Ethernet Technology The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the need for high performance networks.

  • Page 8: Vlan (Virtual Local Area Network)

    Switching is a cost-effective way of increasing the total network capacity available to users on a local area network. A switch increases capacity and decreases network loading by dividing a local area network into different segments, which do not compete with each other for network transmission capacity.

  • Page 9: Power Over Ethernet (Poe)

    Cost Reduction: A VLAN can be used to create multiple broadcast domains, thus eliminating the need of expensive routers. 802.1Q VLAN: The VLAN tagging option is a standard set by the IEEE to facilitate the spanning of VLANs across multiple switches. (Reference: IEEE Std 802.1Q-1998 Virtual Bridged Local Area Networks.) Power over Ethernet (PoE)
  • Page 10 Wire speed reception and transmission Store-and-Forward switching scheme capability to support rate adaptation and ensure data integrity Up to 4K unicast addresses entities per device, self-learning, and table aging 512KBytes packet buffer Supports IEEE 802.3x flow control for full-duplex mode ports Supports Back-pressure flow control for half-duplex mode ports Supports 802.1Q VLAN Supports Port based Trunking...

  • Page 11: Unpacking And Installation

    The site where you install the hub stack may greatly affect its performance. When installing, consider the following pointers: Install the Switch in a fairly cool and dry place. See Technical Specifications for the acceptable temperature and humidity operating ranges.

  • Page 12: Rack Mounting

    Leave at least 10cm of space at the front and rear of the hub for ventilation. Install the Switch on a sturdy, level surface that can support its weight, or in an EIA standard-size equipment rack. For information on rack installation, see the next section, titled Rack Mounting.

  • Page 13: Connecting Network Cable

    AC Power The Switch uses the AC power supply 100-240V AC, 50-60 Hz. The power switch is located at the rear of the unit adjacent to the AC power connector and the system fan. The Switch’s power supply will adjust to the local power source automatically and may be turned on...

  • Page 14: Identifying External Components

    Switch. Front Panel The figure below shows the front panels of the Switch. Figure 3. Front panel of 16-port 10/100 Ethernet Switch with 8-port PoE. LED Indicator: Comprehensive LED indicators display the status of the Switch and the network (see the LED Indicators chapter below).

  • Page 15: Rear Panel

    “plug and play” capability. Just plug-in the network cable to the hub directly and regardless if the end node is a NIC (Network Interface Card) or switch and hub Note: When the port is set to “Forced Mode”, Auto MDI/MDIX will be disabled.

  • Page 16: Understanding Led Indicators

    Figure 5. LED indicators of the Switch Power and CPU LEDs POWER: Power Indicator : When the Power LED lights on, the Switch is receiving power. : When the Power turns off or the power cord has improper connection. CPU: Management Indicator Blinking : When the CPU is working, the CPU LED is blinking.

  • Page 17: Ports 9~16 Ethernet Port Status Leds

    100Mbps When the 100Mbps LED lights on, the respective port is connected to a 100Mbps Fast Ethernet network. : When the respective port is connected to a 10Mbps Ethernet network. PoE Status When the PoE device is connected and the port supplies power Green successfully.

  • Page 18: Configuration

    CONFIGURATION Through the Web browser you can configure Switch functions such as VLAN, Trunking, and QoS… etc. With the attached Web Management Utility, you can easily discover all the Web Management Switches, assign the IP Address, changing the password, and upgrade new firmware.
  • Page 19 Figure 6. Web Management Utility The Web Management Utility is divided into four parts, Discovery List, Monitor List, Device Setting, and Toolbar function, for detailed instructions, follow the section below.

  • Page 20: Discovery List

    Discovery List This is the list where you can discover all the Web management devices in the entire network. By pressing the “Discovery” button, you can list all the Web Management devices in the discovery list. Double click or press the “Add to monitor list” button to select a device from the Discovery List to the Monitor List.

  • Page 21: Monitor List

    Trap IP: Shows the IP where the Trap is to be sent. Subnet Mask: Shows the Subnet Mask set of the device. Gateway: Shows the Gateway set of the device. View Trap: The Trap function can receive the events that happen on the Web Management Switch in the Monitor List.
  • Page 22 There is a light indicator behind the “View Trap” button. When the light is green, it means that there is no trap transmitted, and when it is red, it means that a new trap has been transmitted, reminding us to view the trap.

  • Page 23: Device Setting

    Note: In order to receive Trap information, the Switch has to be configured with Trap IP and Trap Events in the Web browser. These settings are available in the Trap Setting Menu (see Page 40 for detail). Add Item: To add a device to the Monitor List manually, enter the IP Address of the device that you want to monitor.
  • Page 24 Figure 9. Configuration Setting Password Change: You can use this when you need to change the password. Fill in the required passwords in the dialog boxes and press the “Set” button to process the password change immediately. Figure 10. Password Change Firmware Upgrade: When the device has a new function, there will be a new firmware to update the device;...

  • Page 25: Toolbar

    Figure 11. Web Access: Double click the device in the Monitor List or select a device in the Monitor List and press the “Web Access” button to access the device in Web browser. Toolbar The toolbar in the Web Management Utility has four main tabs: File, View, Options, and Help.

  • Page 26: Configuring The Switch

    Configuring the Switch The 16-Port 10/100Mbps Ethernet Web Smart Switch with 8-Port PoE has a Web GUI interface for smart switch configuration. The Switch can be configured through the Web Browser. A network administrator can manage, control, and monitor the Switch from the local LAN.

  • Page 27: Login

    This section indicates how to configure the Switch to enable its smart functions including: Port Setting (Speed/Disable, and Flow Control) VLAN Setting (802.1Q VLAN) Trunking Port Mirroring PoE Setting System Setting Device status and Statistic Login Before you configure this device, note that when the Web Smart Switch is configured through an Ethernet connection, make sure the manager PC is set on same the IP network.
  • Page 28 Or through the Web Management Utility, you do not need to remember the IP Address. Select the device shown in the Monitor List of the Web Management Utility to settle the device on the Web Browser. When the following dialog page appears, enter the default password "admin"...
  • Page 29 Figure 14. Device Status...

  • Page 30: Setup Menu

    Setup Menu When the main page appears, find the Setup menu on the left side of the screen (Figure 15). Click on the setup item that you want to configure. There are eleven options: Port Settings, VLAN Settings, Trunk Settings, Mirror Settings,PoE Settings, Device Status, Statistic, System Settings, Trap Setting, Password Settings, Backup Settings, and Reset Settings as shown in the Main Menu screen.

  • Page 31: Configuring Setup Setting

    Configuring Setup Setting There are six items, including Port Settings, VLAN Settings, Trunk Settings, Mirror Settings, and PoE Settings in Setup menu. Port Settings In the Port Settings menu (Figure 16), this page will display each port’s status. Press the ID parameter to set each port’s Speed, Flow Control, Rate Control Ingress, and Egress.
  • Page 32 Half, Auto, and Disable—for speed or port disable selections. Flow Control: This setting determines whether or not the Switch will be handling flow control. Set FlowCtrl to Enable for avoiding data transfer overflow. If it is set to Disable, there is either no flow control or other...

  • Page 33: Vlan Settings (Virtual Local Area Network)

    VLAN Settings (Virtual Local Area Network) A VLAN is a collection of switch ports that make up a single broadcast domain. You can configure a VLAN for a single switch, or for multiple switches. When you create a VLAN, you...
  • Page 34 Figure 18.

  • Page 35: Trunk Setting

    1 and 4094, Priority value between 0 and 7. Figure 19. Trunk Setting The Trunk function enables the Switch to cascade two devices with double the bandwidth (up to 1600Mbps in full-duplex mode). There are 3 selections for the trunk setting, port “09,10”, port...

  • Page 36: Mirror Setting

    Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of a network switch to another port where the packet can be studied. It enables the manager to keep close track of switch performance and alter it if necessary.

  • Page 37: Poe Setting

    Both (transmit and receive) mode: This mode will duplicate both the data transmitted from and data sent to the source port, then it will forward the data to the sniffer port. Figure 21. PoE Setting When you click on the PoE Setting, the status of the PoE will appear on the screen, it will display the PoE Enable, Power (W), Voltage (V), Current (mA), classification, and Status.
  • Page 38 Figure 22. Press the “Refresh” button to refresh the status of the PoE. Press “SetPoE” button to configure the PoE Port setting, select enable to activate the PoE function from port 1 to port 8, and disable to deactivate the PoE function. Click the “Apply” button to save the settings.

  • Page 39: Device Status

    Figure 23. Device Status Click on the “Status” button to display the device status on this screen. It will display the System Status, Port Status, VLAN Status, Trunk Status, Mirror Status, QoS Status, and PoE Status. Press “Refresh” when you need to renew the posted information. Figure 24.

  • Page 40: Statistic

    Statistic The Statistics Menu screen will display the status of each port packet count. Figure 25. Statistic...
  • Page 41 For detailed packet information, click on the ID parameter as Figure Figure 26.

  • Page 42: System Setting

    System Setting The System Setting includes the Web Server Port, System name, Location name, Login Timeout, IP Address, Subnet Mask, and Gateway. Through the Web Management Utility, you can easily recognize the device by using the System Name and the Location Name.

  • Page 43: Trap Setting

    Trap Setting The Trap Setting enables the device to monitor the Trap through the Web Management Utility. Set the Trap IP Address of the manager where the trap is to be sent. Figure 28. Trap Setting System Events: Monitoring the system’s trap.

  • Page 44: Set Password

    Power over current: A trap when the PoE port’s power is over current. Power short circuit: A trap when the PoE port’s power circuit was short. Set Password Password is the invaluable tool for the manager to secure the Web Management Switch. You can use this function to change the password.

  • Page 45: Backup Setting

    If you forget the password, press the “Reset” button in the rear panel of the Switch. The current setting includes VLAN, Port Setting… etc. will be lost and the Switch will be restored to the default setting. Figure 29. Set Password Backup Setting The backup tools help you to backup the current setting of the Switch.

  • Page 46: Reset Setting

    Figure 30. Backup Setting Note: When restoring a recorded file, the current password will not be erased. Reset Setting The Factory Reset button helps you to reset the device back to the default setting from the factory. Be aware that the entire configuration will be reset;...
  • Page 47 Figure 32. Logout...

  • Page 48: Technical Specifications

    TECHNICAL SPECIFICATIONS General Standards IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3x Full Duplex Flow Control IEEE 802.3af compliant Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps (half-duplex), 20Mbps (full-duplex) Fast Ethernet: 100Mbps (half-duplex), 200Mbps (full-duplex) Topology Star Network Cables 10BASET: 2-pair UTP Cat.

  • Page 49: Physical And Environmental

    Physical and Environmental AC inputs 100-240V AC, 50-60 Hz internal universal power supply Power Consumption 9Watts (max. no PD Device connected) 130Watts (max. with 8 x 15.4 w PoE Device connected) Temperature Operating: 0° ~ 40° C (32° ~ 104° F), Storage: -10° ~ 70° C (14° ~ 158° F) Humidity Operating: 10% ~ 90%, Storage: 5% ~ 90% Dimensions...

  • Page 50: Warranty Information

    Warranty Information (All countries and regions excluding USA) Wichtige Sicherheitshinweise Bitte lesen Sie sich diese Hinweise sorgfältig durch. Heben Sie diese Anleitung für den spätern Gebrauch auf. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind.
  • Page 51 RMA number must be prominently marked on the outside of the package. The package must be mailed or otherwise shipped to D-Link with all costs of mailing/shipping/insurance prepaid.
  • Page 52 D-Link's applicable product documentation as being compatible. D-Link's obligation under this warranty shall be a reasonable effort to provide compatibility, but D-Link shall have no obligation to provide compatibility when there is fault in the third-party hardware or software. D-Link makes no warranty that operation of its software products will be uninterrupted or absolutely error-free, and no warranty that all defects in the software product, within or without the scope of D-Link's applicable product documentation, will be corrected.
  • Page 53 Hardware will be warranted for the remainder of the original Warranty Period from the date of original retail purchase. If a material defect is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to repair or replace the defective Hardware, the price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware.
  • Page 54 Submitting A Claim: The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the product is within warranty, the customer shall submit a claim to D-Link as outlined below: •...
  • Page 55 SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT.
  • Page 57 REGISTRATION Register your product on-line at: http://support.dlink.com/register Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.

Table of Contents