Wichtige Sicherheitshinweise 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den spätern Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4.
FCC Warning This equipment has been tested and found to comply with the limits for a Class A device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Warranty service for software products may be obtained by contacting a D-Link office within the applicable warranty period. A list of D-Link offices is provided at the back of this manual, together with a copy of the Registration Card. If a Registration Card for the product in question has not been returned to a D-Link office, then a proof of purchase (such as a copy of the dated purchase invoice) must be provided when requesting warranty service.
D-Link's obligation under this warranty shall be a reasonable effort to provide compatibility, but D-Link shall have no obligation to provide compatibility when there is fault in the third-party hardware or software. D-Link makes no warranty that operation of its software products will be uninterrupted or absolutely error-free, and no warranty that all defects in the software product, within or without the scope of D-Link's applicable product documentation, will be corrected.
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide BOUT UIDE This User’s guide tells you how to install the DES-1048G, how to connect it to an Ethernet network, and how to set the configuration using the built-in console interface. Conventions For simplicity, this documentation uses the terms “Switch” (first letter upper case) to refer to the DES-1048G Ethernet Switch, and “switch”...
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide NTRODUCTION This section describes the features of the Switch, as well as giving some background information about Fast Ethernet, Gigabit Ethernet, and switching technology. Fast Ethernet Technology The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the need for high performance networks.
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide Ethernet NIC’s are able to perform 10 times the number of operations in the same amount of time. In addition, the phenomenal bandwidth delivered by Gigabit Ethernet is the most cost- effective method to take advantage of today and tomorrow’s rapidly improving switching and routing internetworking technologies.
DES-1048G 10/100/1000 Mbps Stand-alone Switch General Description of Switch The DES-1048G is a stand-alone unmanaged switch. It is equipped with forty-eight ports providing dedicated 10 or 100 Mbps bandwidth. These ports can be used for connecting PCs, servers, and hubs. The forty-eight dual speed ports use standard twisted-pair cabling and are ideal for segmenting networks into small, connected subnets.
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide Performance Features (continued) ♦ Data filtering rate eliminates all error packets, runts, etc. at 1,488,100 pps per port at 100% of wire-speed for 1000Mbps speed ♦ Support static filtering (based on MAC address) ♦...
♦ Four rubber feet with adhesive backing ♦ RS-232 Console Cable ♦ Six screws and two brackets for rack mounting If any item is found missing or damaged, please contact your local D-Link Reseller for replacement. Setup The site where you install the DES-1048G Switch may greatly affect its performance.
Allow enough ventilation space between the switch and any other objects in the vicinity. Figure 2-1 DES-1048G Switch installed on a Desktop or Shelf Rack Installation The Switch can be mounted in a standard 19” rack. Use the following diagrams to guide you.
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide Figure 2-3 Mount Switch in Rack Power on Plug one end of the AC power cord into the power connector of the switch and the other end into the local power source outlet.
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide DENTIFYING XTERNAL OMPONENTS This chapter describes the front panel display, the rear panel, and LED indicators of the DES-1048G. Front Panel The front panel of the Switch consists of an LED indicator for Status, two indicators for the optional GBIC ports and two indicators for each UTP copper port.
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide Side Panels The right side panel of the Switch contains two system fans. The left side panel contains heat vents. Figure 3-3. Side panel view of the Switch. The system fans are used to dissipate heat. The sides of the system also provide heat vents to serve the same purpose.
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide GBIC Port LEDs The GBIC module LEDs are located on the front of the Switch next to the Status LED. Present Steady green indicates the presence of a functioning GBIC port. This will be unlit otherwise.
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide ONNECTING WITCH This chapter describes how to connect the DES-1048G to your Ethernet network. Switch to End Node End nodes include PCs outfitted with a 10, 100 or 10/100 Mbps RJ-45 Ethernet/Fast Ethernet Network Interface Card (NIC) and most routers. The RJ-45 UTP ports on NICs and most routers are MDI-II.
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide Switch to Hub or Switch These connections can be accomplished in a number of ways. The most important consideration is that when using a normal, straight-through cable, the connection should be made between a normal crossed port (Ports 1–48) and an uplink (MDI-II) port.
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide Connecting to Network Backbone or Server The optional GBIC fiber optic ports are ideal for uplinking to a network backbone or network server via 1000BASE-SX, 1000BASE-LX or 1000BASE-LH fiber optic cable. These ports operate at 1000 Mbps in full duplex mode only. GBIC port modules can be installed or taken out without powering off or disconnecting the Switch.
Configuring the Switch is discussed in detail. Local Console Management Local console management involves the administration of the DES-1048G Switch via a direct connection to the RS-232 DTE console port. This is an Out-Of-Band connection, meaning that it is on a different circuit than normal network communications, and thus works even when the network is down.
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide Once you have connected to the console port on the switch, you should see a window like that pictured in Figure 5-1. If the screen appears but is blank, press “Control” and “R”...
Page 24
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide Figure 5-2. Management Console Screen (page 2) Page 3 of the Management Console Screen shown below can be will display the default setting (Auto) for the optional GBIC port modules. GBIC ports operate at 1000Mbps in full duplex only with flow control enabled.
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide Software Features The Switch management software provides the ability to configure the port speed, duplex and flow control for each UTP port. The default setting is Auto for all ports. This setting enables Nway to auto-negotiate port speed with the device to which the port is connected.
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide ABLES AND ONNECTORS When connecting the Switch to another switch, a bridge or hub, a crossover cable is necessary. Please review these products for matching cable pin assignment. The following diagrams and tables show the standard RJ-45 receptacle/connector and their pin assignments.
Page 29
DES-1048G Fast Ethernet/Gigabit Ethernet Switch User’s Guide RJ-45 Pin Assignments Contact MDI-X Port MDI-II Port RD+ (receive) TD+ (transmit) RD- (receive) TD- (transmit) TD+ (transmit) RD+ (receive) Not used Not used Not used Not used TD- (transmit) RD- (receive) Not used...
Page 31
Le Florilege #2, Allee de la Fresnerie 78330 Fontenay Le Fleury France TEL: 33-1-30238688 FAX: 33-1-3023-8689 URL: www.dlink-france.fr E-MAIL: info@dlink-france.fr GERMANY D-LINK CENTRAL EUROPE/D-LINK DEUSTSCHLAND GMBH Schwalbacher Strasse 74, 65760 Eschborn Germany TEL: 49-(0) 6196-7799-0 FAX: 49-(0) 6196-7799-300 URL: www.dlink.de E-MAIL: mbischoff@dlink.de, mboerner@dlink.de INDIA D-LINK INDIA Plot No.5, Kurla-Bandra Complex Road,...
8. What category best describes your company? Aerospace Engineering Education Finance Hospital Legal Insurance/Real Estate Manufacturing Retail/Chainstore/Wholesale Government Transportation/Utilities/Communication System house/company Other____________________________________________________________ 9. Would you recommend your D-Link product to a friend? Don't know yet 10.Your comments on this product? _________________________________________________ _________________________________________________________________________________ _________________________________________________________________________________ _________________________________________________________________________________ _________________________________________________________________________________...