D-Link des-1316 Quick Installation Manual
Poe web-smart switch
Hide thumbs
Also See for des-1316:
- Quick installation manual (66 pages) ,
- Manual (57 pages) ,
- Manual (46 pages)
Table of Contents
Advertisement
Quick Links
Before Your Begin
This Quick Installation Guide gives step-by-step instructions for setting up the D-Link
DES-1316 PoE Web-Smart Switch. The model you have purchased may appear slightly
different from those shown in the illustrations. For more detailed information about the
switch, its components, making network connections and technical specifications,
please refer to the User's Manual on master CD included with your switch.
Check Your Package Contents
If any item is found missing or damaged, please contact your local reseller for
replacement.
©2004 D-Link System, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective
16-Port 10/100Mbps Ethernet Web Smart Switch
with 8-Port PoE
CD-Rom(Containing manual and Utility
Installation)
AC power cord (Suitable for your area's
electrical power connections)
holders. Software and specifications subject to change without notice.
16-Port 10/100Mbps Ethernet Web
Smart Switch with 8-Port PoE
1
DES-1316
Advertisement
Table of Contents
Related Manuals for D-Link des-1316
Summary of Contents for D-Link des-1316
-
Page 1: Check Your Package Contents
If any item is found missing or damaged, please contact your local reseller for replacement. ©2004 D-Link System, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and specifications subject to change without notice. -
Page 2: Rack Mounting
Setup The DES-1316 PoE Web Smart Switch The setup of the Switch can be performed using the following steps: A. Install DES-1316 in a fairly cool and dry place. See Technical Specifications for the acceptable temperature and humidity operating ranges. -
Page 3: Connecting Network Cable
Connecting Network Cable DES-1316 support 16 10/100M Ethernet ports and Port 1 ~ port 8 are PoE Enable ports, these PoE port will automatically activated when a compatible terminal is identified, the Switch will supply power through the Ethernet port to the connected PoE device. -
Page 4: Identifying External Components
Identifying External Components This chapter describes the front panel, rear panel, and LED indicators of the Switch. Front Panel The figure below shows the front panels of the Switch. PoE Ports ┌――┐ └――――┘ └―――┘ LED Indicators Ethernet Ports Front panel of the Switch LED Indicator: Comprehensive LED indicators display the status of the switch and the network (see the LED Indicators chapter below). -
Page 5: Rear Panel
crossover detection function gives true “plug and play” capability, just need to plug-in the network cable to the hub directly and don’t care if the end node is NIC (Network Interface Card) or switch and hub Note: When the port was set to “Forced Mode”, the Auto MDI/MDIX will be disabled. Rear Panel AC Power Connector Reset Button... -
Page 6: Power And Cpu Leds
Power and CPU LEDs POWER: Power Indicator When the Power LED lights on, the Switch is receiving power. When the Power turns off or the power cord has improper connection. CPU: Management Indicator Blinking When the CPU is working, the CPU LED is blinking. On/Off The CPU is not working. -
Page 7: Ports 9~16 Ethernet Port Status Leds
Ports 9~16 Ethernet port status LEDs Link/ACT: Link/Activity When the Link/ACT LED lights on, the respective port is successfully connected to an Ethernet network. When the Link/ACT LED is blinking, the port is transmitting or receiving data on Blinking the Ethernet network. No link. -
Page 8: Installing The Web Management Utility
Installing the Web Management Utility The following gives instructions guiding you through the installations of the Web Management utility. 1. Insert the Utility CD in the CD-Rom Drive. 2. From the Start menu on the Windows desktop, choose Run. 3. In the Run dialog box, type D:\Web Management Utility\setup.exe (D:\ depends where your CD-Rom drive is located) and click OK. -
Page 9: Configuring The Switch
Configuring the Switch The 16-Port 10/100Mbps Ethernet Web Smart Switch with 8-Port PoE has a Web GUI interface for smart switch configuration. The Switch can be configured through the Web Browser. A network administrator can manage, control and monitor the switch from the local LAN. - Page 10 Or through the Web Management Utility, you do not need to remember the IP Address, select the device shown in the Monitor List of the Web Management Utility to settle the device on the Web Browser. When the following dialog page appears, remain enter the default password "admin" and press Login to enter the main configuration window.
- Page 11 Setup Menu When the main page appears, find the Setup menu in the left side of the screen (Figure 14). Click on the setup item that you want to configure. There are eleven options: Port Settings, VLAN Settings, Trunk Settings, Mirror Settings, QoS Settings, PoE Settings, Device Status, Statistic, System Settings, Trap Setting, Password Settings, Backup Settings and Reset Settings as shown in the Main Menu screen.
-
Page 12: Technical Support
Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our website, or by phone.