Integra DTR-40.2 Instruction Manual page 51

Speaker Configuration
This setting is set automatically by Audyssey MultEQ
Room Correction and Speaker Setup function
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify "Full Band" for speakers that can output low fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speaker's manuals to determine the
optimum crossover frequencies. If you set up your speak-
ers using Audyssey MultEQ Room Correction and
Speaker Setup, please make sure manually that any THX
speakers are set to "80Hz(THX)" crossover.
■
Subwoofer

Yes:
Select if a subwoofer is connected.

No:
Select if no subwoofer is connected.
■
Front

Full Band

40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
to 130Hz, 150Hz, 200Hz
Note
• If the "Subwoofer" setting is set to "No", the "Front" setting is
fixed at "Full Band".
■
Center *1 , Surround *1 , Surr Back

Full Band

40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
to 130Hz, 150Hz, 200Hz

None:
Select if no speaker is connected.
■
Front Wide *1*2*4*6 , Front High

Full Band

40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
to 130Hz, 150Hz, 200Hz

None:
Select if no speaker is connected.
Note
*1
"Full Band" can be selected only when "Full Band" is
selected in the "Front" setting.
*2
If the "Surround" setting is set to "None", this setting cannot
be selected.
*3
If the "Surround" setting is set to anything other than "Full
Band", "Full Band" cannot be selected here.
*4
If the "Speakers Type(Front)" setting is set to "Bi-Amp"
(➔ 50), this setting cannot be selected.
*5
If the Powered Zone 2 is being used
not be selected.
*6 If the "Powered Zone 2" setting is set to
setting cannot be selected.
■
®
(➔ 28).
• If the "Surr Back" setting is set to "None"
■
■
*2*3*4*5
• This function can be set only if the "Subwoofer" setting is set to
• If you're using THX-certified speakers, select "Off(THX)".
*1*2*4*5
(➔ 77), this setting can-
"Act"
(➔ 77), this
Surr Back Ch
1ch:
Select if only one surround back speaker is con-
nected.
2ch:
Select if two (left and right) surround back speakers
are connected.
Note
cannot be selected.
LPF of LFE
(Low-Pass Filter for the LFE Channel)
80Hz, 90Hz, 100Hz, 110Hz, 120Hz
With this setting, you can specify the cutoff frequency
of the LFE channel's low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only
applies to sources that use the LFE channel.
Double Bass
This setting is NOT set automatically by
Audyssey MultEQ Room Correction and Speaker Setup
function (➔ 28).
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left, right, and
center channels to the subwoofer.
On:
Double Bass function on.
Off(THX):
Double Bass function off.
Note
"Yes", and the "Front" setting is set to "Full Band".
(➔ 51), this setting
En
51