Related Manuals for Clarke CDE7B
Summary of Contents for Clarke CDE7B
- Page 1 DUST EXTRACTOR MODEL NO: CDE7B PART NO: 6470305 OPERATING & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC0321 - REV 4...
- Page 2 INTRODUCTION Thank you for purchasing this CLARKE Dust Extractor which is intended to keep work areas free from dust particles & wood shavings etc. Please read this manual thoroughly and follow the instructions carefully. Before attempting to use the product, thoroughly familiarise yourself with the product &...
-
Page 3: General Safety Precautions
4. Never use a power product if any part is damaged. Have it inspected and repaired by your Clarke dealer. Do not use if the electric cable, plug, or the machine itself, is in poor condition. - Page 4 14. Do not attempt to repair or modify the dust extractor or attempt any electrical repair yourself. Consult a qualified electrician or the Clarke Service Department on 020 8988 7400. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 5: Electrical Connections
ELECTRICAL CONNECTIONS WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. -
Page 6: Unpacking And Assembly
UNPACKING & ASSEMBLY When unpacking please check contents and advise your dealer immediately if any parts are missing. The component parts of the machine are as follows. The numbers in brackets refer to the parts diagram on page 15. INVENTORY 1 x Collector Support (35) 1 x Collector Body &... - Page 7 3. Attach column and motor plate, (20) to the base plate using bolts and washers supplied, (DO NOT OVERTIGHTEN). When viewed from the back, ensure threaded holes in side of the motor plate are on the right hand side, (see Fig 1). FIG 1 NOTE: Before installing the motor and...
- Page 8 FIG 3 6. Attach the collector, (23) to the collector body as shown in Fig 4, using 6 hex head screws and washers, (supplied), (DO NOT OVERTIGHTEN). Ensure the gasket, (22) is fitted between the two units. FIG 4 7. Attach the two bag support rods, (31) using screws, nuts and washers supplied, one on either side of the collector, (see Fig 5).
-
Page 9: Operation
Clarke dealer. To switch ON, press the switch cover (see fig. 8) down and slide in direction of arrow and lift up, this will expose the ON/OFF buttons, (see fig 9) Push the ON button, (green button ‘I’). -
Page 10: Maintenance
NOTE: In case of emergency, close the switch cover quickly, cover will latch down and motor will be switched OFF. To switch OFF normally, press OFF button, (red button ‘O’), always close cover to prevent accidental starting. MAINTENANCE Always inspect the machine before use and ensure it is in top condition. Regularly inspect the filter for damage before use and replace if necessary. -
Page 11: Troubleshooting
Dust buildup Consult your Clarke inside housing. dealer. Excessive noise Defective motor Have machine repaired by your Clarke dealer Machine runs but fails to Low voltage or motor Have machine repaired reach full speed. defective. by your Clarke dealer Motor fails to develop Supply circuit overloaded. -
Page 12: Component Parts
COMPONENT PARTS Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 13 Switch Key switch Adaptor ACCESSORIES The Clarke Dust Extractor Kit, model: ‘CDE Kit’, Part No: 6470312 can be used with the CDE7B. It consists of: • Hose 2.5metres (94”) Long X 102mm (4”) ID • Adapter/ 2” Reducer Both items fit directly onto the safety adapter already fitted to the dust extractor inlet cover.
- Page 14 DECLARATION OF CONFORMITY-UK Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 15: Declaration Of Conformity-Eu
DECLARATION OF CONFORMITY-EU Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...