Kenwood TH-K2AT Service Manual page 33

(2)Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3)Turn the encoder to display the upper limit frequency on
the LCD.
(4)Repeat steps (4) to (7) of " 1 13.8V TX L pow er (Low er limit
frequency)" described on page 32.
L. DCS modulation balance
(1)Press the [LAM P] or [M ONI] key on the transceiver to display
" DCS.BAL" on the LCD. Press the [F] key and then the
[PTT] key repeatedly to turns the "
(2)When the [PTT] key is pressed to enable transmit mode, a
100Hz square w avef orm is int ernally generat ed and
modulated.
(3)While observing the w aveforms on the oscilloscope, turn
the semi-fixed volume (VR6) to adjust the DCS modulation
w aveform to a square w aveform.
(4)When the DCS modulation w aveform becomes a square
w aveform, release the [PTT] key.
M .Tone deviat ion (Low er lim it frequency, cent er
frequency, upper limit frequency)
1 Tone deviation (Low er limit frequency)
(1)Press the [LAM P] or [M ONI] key on the transceiver to display
" DVL" on the LCD.
In this case, the " " icon appears. Press the [F] key and
then the [PTT] key repeatedly to turn the "
The current adjustment value is displayed at the low er digits
of the frequency display, and the value stored in the
EEPROM is displayed on the memory channel number
display.
(2)Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3)Turn the encoder to display the low er limit frequency on
the LCD.
(4)Press the [CALL] key to sw itch to the adjustment display.
(5)When the [PTT] key is pressed to enable transmit mode, a
preset tone frequency (151.4Hz) is internally generated and
modulated.
(6)Turn the encoder to change the current adjustment value
and adjust tone deviation.
(7)Press the [M ENU] key to w rite the current adjustment value
into the EEPROM .
ADJUSTM ENT
2 Tone deviation (Center frequency)
(1)Press the [LAM P] or [M ONI] key on the transceiver to display
" icon ON.
(2)Press the [VFO], [M R] or [CALL] key to sw itch to the
(3)Turn the encoder to display the center frequency on the
(4)Repeat steps (4) to (7) of " 1 Tone deviation (Low er limit
3 Tone deviation (Upper limit frequency)
(1)Press the [LAM P] or [M ONI] key on the transceiver to display
(2)Press the [VFO], [M R] or [CALL] key to sw itch to the
(3)Turn the encoder to display the upper limit frequency on
" icon ON.
(4) Repeat steps (4) to (7) of " 1 Tone deviation (Low er limit
N. DCS deviation (Lower limit frequency, center frequency,
1 DCS deviation (Low er limit frequency)
(1)Press the [LAM P] or [M ONI] key on the transceiver to display
(2)Press the [VFO], [M R] or [CALL] key to sw itch to the
(3)Turn the encoder to display the low er limit frequency on
TH-K2AT/K2E/K2ET
" DVC" on the LCD.
In this case, the " " icon appears. Press the [F] key and
then the [PTT] key repeatedly to turn the "
frequency display.
LCD.
frequency)" described on page 33.
" DVH" on the LCD.
In this case, the " " icon appears. Press the [F] key and
then the [PTT] key repeatedly to turn the "
frequency display.
the LCD.
frequency)" described on page 33.
upper limit frequency)
" DVL" on the LCD.
In this case, the " " icon appears. Press the [F] key and
then the [PTT] key repeatedly to turn the "
The current adjustment value is displayed at the low er digits
of the frequency display, and the value stored in the
EEPROM is displayed on the memory channel number
display.
frequency display.
the LCD.
" icon ON.
" icon ON.
" icon ON.
33