Kenwood TH-K2AT Service Manual page 29

D. S-meter (Tw o segments in S-meter light, all segments
in S-meter light)
1 S-meter (Tw o segments in S-meter light)
(1)Press the [LAM P] or [M ONI] key on the transceiver to display
" S1" on the LCD.
The current RSSI level value is displayed at the low er digits
of the frequency display, and the value stored in the
EEPROM is displayed on the memory channel number
display.
(2)Press the [M ENU] key to w rite the current RSSI level value
into the EEPROM .
2 S-meter (All segments in S-meter light)
(1)Press the [LAM P] or [M ONI] key on the transceiver to display
" S9" on the LCD.
(2)Press the [M ENU] key to w rite the current RSSI level value
into the EEPROM .
E. RX BPF (Low er limit frequency, center frequency, upper
limit frequency)
1 RX BPF (Low er limit frequency)
(1)Press the [LAM P] or [M ONI] key on the transceiver to display
" BPL" on the LCD.
The current BPF tuning value is displayed at the low er digits
of the frequency display, and the value stored in the
EEPROM is displayed on the memory channel number
display.
(2)Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3)Turn the encoder to display the low er limit frequency on
the LCD.
(4)Press the [CALL] key to sw itch to the adjustment display.
(5)Turn the encoder to change the current BPF tuning value
and adjust RX BPF.
(6)Press the [M ENU] key to w rite the current BPF tuning value
into the EEPROM .
TH-K2AT/K2E/K2ET
ADJUSTM ENT
2 RX BPF (Center frequency)
(1)Press the [LAM P] or [M ONI] key on the transceiver to display
" BPC" on the LCD.
(2)Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3)Turn the encoder to display the center frequency on the
LCD.
(4)Repeat st eps (4) t o (6) of " 1 RX BPF (Low er lim it
frequency)" described on page 29.
3 RX BPF (Upper limit frequency)
(1)Press the [LAM P] or [M ONI] key on the transceiver to display
" BPH" on the LCD.
(2)Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3)Turn the encoder to display the upper frequency on the
LCD.
(4)Repeat st eps (4) t o (6) of " 1 RX BPF (Low er lim it
frequency)" described on page 29.
F. 7.5V TX H pow er (Low er lim it frequency, cent er
frequency, upper limit frequency)
1 7.5V TX H pow er (Low er limit frequency)
(1)Press the [LAM P] or [M ONI] key on the transceiver to display
" P7L" on the LCD.
In this case, the "
The current APC value is displayed at the low er digits of
the frequency display, and the value stored in the EEPROM
is displayed on the memory channel number display.
(2)Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3)Turn the encoder to display the low er limit frequency on
the LCD.
(4)Press the [CALL] key to sw itch to the adjustment display.
(5)Press the [PTT] key to enable the transmit mode.
(6)Adjust the output voltage from DC pow er supply until the
voltage at the battery terminal becomes 7.5V w hile the
transceiver is transmitting.
(7)Turn the encoder to change the current APC value and adjust
the transmission pow er.
" icon appears.
29