Kenwood TH-K2AT Service Manual page 30

TH-K2AT/K2E/K2ET
(8) Press the [M ENU] key to w rite the current APC value into
the EEPROM .
2 7.5V TX H pow er (Center frequency)
(1) Press the [LAM P] or [M ONI] key on the transceiver to display
" P7C" on the LCD.
In this case, the " " icon appears.
(2) Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3) Turn the encoder to display the center frequency on the
LCD.
(4) Repeat steps (4) to (8) of " 1 7.5V TX H pow er (Low er limit
frequency)" described on page 29.
3 7.5V TX H pow er (Upper limit frequency)
(1) Press the [LAM P] or [M ONI] key on the transceiver to display
" P7H" on the LCD.
In this case, the " " icon appears.
(2) Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3) Turn the encoder to display the upper limit frequency on
the LCD.
(4) Repeat steps (4) to (8) of " 1 7.5V TX H pow er (Low er limit
frequency)" described on page 29.
G. 7.5V TX M pow er (Low er lim it frequency, cent er
frequency, upper limit frequency)
1 7.5V TX M pow er (Low er limit frequency)
(1) Press the [LAM P] or [M ONI] key on the transceiver to display
" P7L" on the LCD.
In this case, the " " icon appears.
The current APC value is displayed at the low er digits of
the frequency display, and the value stored in the EEPROM
is displayed on the memory channel number display.
(2) Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3) Turn the encoder to display the low er limit frequency on
the LCD.
(4) Press the [CALL] key to sw itch to the adjustment display.
30
ADJUSTM ENT
(5) Press the [PTT] key to enable the transmit mode.
(6) Adjust the output voltage from DC pow er supply until the
voltage at the battery terminal becomes 7.5V w hile the
transceiver is transmitting.
(7) Turn the encoder to change the current APC value and adjust
the transmission pow er.
(8) Press the [M ENU] key to w rite the current APC value into
the EEPROM .
2 7.5V TX M pow er (Center frequency)
(1) Press the [LAM P] or [M ONI] key on the transceiver to display
" P7C" on the LCD.
In this case, the "
(2) Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3) Turn the encoder to display the center frequency on the
LCD.
(4) Repeat steps (4) to (8) of " 1 7.5V TX M pow er (Low er limit
frequency)" described on page 30.
3 7.5VTX M pow er (Upper limit frequency)
(1) Press the [LAM P] or [M ONI] key on the transceiver to display
" P7H" on the LCD.
In this case, the "
(2) Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3) Turn the encoder to display upper limit frequency on the
LCD.
(4) Repeat steps (4) to (8) of " 1 7.5V TX M pow er (Low er limit
frequency)" described on page 30.
H. 7.5V TX L pow er (Low er lim it frequency, cent er
frequency, upper limit frequency)
1 7.5V TX L pow er (Low er limit frequency)
(1) Press the [LAM P] or [M ONI] key on the transceiver to display
" P7L" on the LCD.
In this case, the "
The current APC value is displayed at the low er digits of
the frequency display, and the value stored in the EEPROM
is displayed on the memory channel number display.
" icon appears.
" icon appears.
" icon appears.