Kenwood TH-K2AT Service Manual page 32

TH-K2AT/K2E/K2ET
J. 13.8V TX M pow er (Low er limit frequency, center
frequency, upper limit frequency)
1 13.8V TX M pow er (Low er limit frequency)
(1) Press the [LAM P] or [M ONI] key on the transceiver to display
" P13L" on the LCD.
In this case, the "
The current APC value is displayed at the low er digits of
the frequency display, and the value stored in the EEPROM
is displayed on the memory channel number display.
(2) Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3) Turn the encoder to display the low er limit frequency on
the LCD.
(4) Press the [CALL] key to sw itch to the adjustment display.
(5) Press the [PTT] key to enable the transmit mode.
(6) Turn the encoder to change the current APC value and adjust
the transmission pow er.
(7) Press the [M ENU] key to w rite the current APC value into
the EEPROM .
2 13.8V TX M pow er (Center frequency)
(1) Press the [LAM P] or [M ONI] key on the transceiver to display
" P13C" on the LCD.
In this case, the "
(2) Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3) Turn the encoder to display the center frequency on the
LCD.
(4) Repeat steps (4) to (7) of " 1 13.8V TX M pow er (Low er
limit frequency)" described on page 31.
3 13.8V TX M pow er (Upper limit frequency)
(1) Press the [LAM P] or [M ONI] key on the transceiver to display
" P13H" on the LCD.
In this case, the "
(2) Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3) Turn the encoder to display the upper limit frequency on
the LCD.
32
ADJUSTM ENT
" icon appears.
" icon appears.
" icon appears.
(4) Repeat steps (4) to (7) of " 1 13.8V TX M pow er (Low er
limit frequency)" described on page 32.
K. 13.8V TX L pow er (Low er limit frequency, cent er
frequency, upper limit frequency)
1 13.8V TX L pow er (Low er limit frequency)
(1) Press the [LAM P] or [M ONI] key on the transceiver to display
" P13L" on the LCD.
In this case, the " " icon appears.
The current APC value is displayed at the low er digits of
the frequency display, and the value stored in the EEPROM
is displayed on the memory channel number display.
(2) Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3) Turn the encoder to display the low er limit frequency on
the LCD.
(4) Press the [CALL] key to sw itch to the adjustment display.
(5) Press the [PTT] key to enable transmit mode.
(6) Turn the encoder to change the current APC value and adjust
transmission pow er.
(7) Press the [M ENU] key to w rite the current APC value into
the EEPROM .
2 13.8V TX L pow er (Center frequency)
(1) Press the [LAM P] or [M ONI] key on the transceiver to display
" P13C" on the LCD.
In this case, the " " icon appears.
(2) Press the [VFO], [M R] or [CALL] key to sw itch to the
frequency display.
(3) Turn the encoder to display the center frequency on the
LCD.
(4) Repeat steps (4) to (7) of " 1 13.8V TX L pow er (Low er limit
frequency)" described on page 32.
3 13.8V TX L pow er (Upper limit frequency)
(1) Press the [LAM P] or [M ONI] key on the transceiver to display
" P13H" on the LCD.
In this case, the " " icon appears.