Important Safety Instructions; Specifications - Simer BW85 Series Owner's Manual

Safety

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains
important instructions that should be followed during
installation, operation, and maintenance of the product.
Save this manual for future reference.
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for one of
the following signal words and be alert to the potential
for personal injury!
indicates a hazard which, if not avoided, will
result in death or serious injury.
indicates a hazard which, if not avoided,
could result in death or serious injury.
indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE addresses practices not related to personal injury.
Description
This non-corrosive pump, with reversible flow direction,
is designed to pump water only.
Risk of fire or explosion . Can cause
severe injury, property damage or death. Do not use in
explosive atmospheres. Do not pump flammable liquids.

Specifications

Liquid Temp. Range. . . . . . . . . . . 35° to 120° F (1.7° to 50° C)
NOTICE Never operate the pump for more than two
hours at a time. Never run the pump dry!
NOTICE This unit is not designed for applications
involving salt water or brine! Use with salt water or brine
will void warranty.
Performance
Total Feet (m)
0 (0) 10 (3)
Capacity Gallons (L) / Hour
450 (1,703) 390 (1,476) 300 (1,136)
DC Motors
1. DC motors must be connected to a fully charged
automotive, tractor or marine type battery of the
proper voltage.
2. Life expectancy of the motor is 500 to 1000 hours.
For more information, see your retailer, or call Simer
customer service at 1-800-468-7867.
For parts or assistance, call Simer Customer Service at 1-800-468-7867
20 (6.1) 30 (9.1) 40 (12.2)
225 (852) 130 (492)
General Safety Information
1. This equipment is only for use with an automotive,
tractor or marine type battery fully charged to
12 Volts DC.
Risk of electric shock . Battery current
can cause severe burns and start a fire if the battery
is short circuited.
Risk of burns . Battery posts, terminals
and related accessories contain lead and lead
compounds, chemicals known to the State of
California to cause cancer and reproductive harm.
Wash hands after handling.
2. Know the pump application, limitations, and
potential hazards.
3. Do not use this pump in water with fish present.
4. Release all pressure within the system before
servicing any component.
5. Drain all water from the system before servicing.
6. Secure the discharge line before starting the pump.
An unsecured discharge line can whip, possibly
causing personal injury and/or property damage.
7. Check hoses for weak or worn condition before each
use, making certain all connections are secure.
8. Periodically inspect the pump and system
components. Keep free of debris and foreign
objects. Perform routine maintenance as required.
See Maintenance.
9. Provide a means of pressure relief for pumps whose
discharge line can be shut-off or obstructed.
10. Personal Safety:
a. Wear safety glasses at all times when working
with the pumps.
b. Keep work area clean, uncluttered and
properly lighted.
c. Keep visitors at a safe distance from the
work area.
d. Make the workshop child-proof – with padlocks,
master switches, and by removing starter keys.
11. When wiring a DC pump, follow all of the electrical
and safety codes that apply.
12. All wiring is to be 12 gauge stranded copper wire
that is:
A. Water resistant
B. Oil resistant
C. Flame resistant
NOTICE This pump is equipped with a permanent
magnet type 12 Volt reversible DC motor. Be sure it
is connected properly as illustrated for the direction
of flow indicated by the arrows on the pump case
(see Figure 1).
3