Important Safety Instructions; Specifications - Simer 2905-04 Owner's Manual

Safety

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains important
instructions that should be followed during installation,
operation, and maintenance of the product.
safety alert symbol. When you see this symbol on your pump
or in this manual, look for one of the following signal words
and be alert to the potential for personal injury!
indicates a hazard which, if not avoided, will
result in death or serious injury.
indicates a hazard which, if not avoided, could
result in death or serious injury.
indicates a hazard which, if not avoided, could
result in minor or moderate injury.
NOTICE addresses practices not related to personal injury.
Carefully read and follow all safety instructions in this manual
and on pump.
Keep safety labels in good condition. Replace missing or
damaged safety labels.
California Proposition 65 Warning
This product and related accessories contain
chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm.
1. Know the pump application, limitations, and potential
hazards. Pump water only with this pump.
2. Do not use this pump in water with fish present. If any oil
leaks out of the motor it can kill fish.
3. Disconnect the power before servicing.
4. Release all pressure within the system before servicing any
component.
5. Drain all the water from the system before servicing.
6. Secure the discharge line before starting the pump. An
unsecured discharge line will whip, possibly causing
personal injury and/or property damage.
7. Check hoses for weak or worn condition before each use,
making certain that all connections are secure.
8. Periodically inspect the sump, pump and system
components. Keep free of debris and foreign objects. Perform
routine maintenance as required.
9. Provide a means of pressure relief for pumps whose
discharge line can be shut-off or obstructed.
10. Personal Safety:
a. Wear safety glasses at all times when working with
pumps.
b. Keep work area clean, uncluttered and properly lighted –
replace all unused tools and equipment.
c. Keep visitors at a safe distance from work area.
d. Make workshop child-proof – with padlocks, master
switches, and by removing starter keys.
11. When wiring an electrically driven pump, follow all
electrical and safety codes that apply.
12. This equipment is only for use on 115 volt and is equipped
with an approved 3-conductor cord and 3-prong, grounding-
type plug.
Risk of electric shock. Can shock, burn or
kill. To reduce the risk of electric shock, pull the plug
before servicing. Pump is supplied with a grounding
conductor and grounding-type attachment plug. Be sure it
is connected only to a properly grounded grounding-type
receptacle.
For parts or assistance, call Simer Customer Service at
Where a 2-prong wall receptacle is encountered, it must
be replaced with a properly grounded 3-prong receptacle
installed in accordance with codes and ordinances that apply.
This pump has not been investigated for use in swimming
This is the
pool areas.
13. A ground fault circuit interrupter is recommended for use
with any electrical appliance submerged in water. Installation
and all wiring should be performed by a qualified electrician.
14. Make certain the power source conforms to the requirements
of your equipment.
15. Protect the electrical cord from sharp objects, hot surfaces,
oils, and chemicals. Avoid kinking the cord. Replace or repair
damaged or worn cords immediately.
16. Do not touch an operating motor. Motors can operate at
high temperatures.
17. Do not handle the pump or pump motor with wet hands or
when standing on a wet or damp surface, or in water.
your basement has water or moisture on floor, do not walk on
the wet area until all power has been turned off. If the shut-off
box is in the basement, call electric company or hydro authority
to shut-off the service to house, or call your local fire department
for instructions. Failure to follow this warning can result in fatal
electrical shock.
18. DO NOT splice the electrical power cord.
19. DO NOT allow the electrical cord plug to be submerged.
20. DO NOT use extension cords. They are a fire hazard and
can reduce voltage sufficiently to prevent pumping and/or
damage motor.
21. Connect or wire the pump to an individual branch circuit
with no other outlets or equipment in the circuit. Size fuses
or circuit breakers according to the specifications.

Specifications

Power supply required ........................................... 115V, 60 HZ
Liquid Temp. Range ............................... 32° F-120° F (0°-49° C)
Individual Branch Circuit Required............................... 15 Amps
Discharge Adapter ................................................. 1-1/4" MNPT
Pump water only with this pump.
NOTICE This unit is not designed as a waterfall or fountain
pump, or for applications involving salt water or brine! Use with
waterfalls, fountains, salt water or brine will void warranty.
Do not use where water recirculates.
Not designed for use as a swimming pool drainer.
Risk of electric shock. Can shock, burn or kill. If
800-468-7867 / 800-546-7867
2