Standard Equipment; Telescope Assembly - Bushnell 78-9512 User Manual

STANDARD EQUIPMENT

Complete Main Telescope Assembly
Full Length Variable-Height Hardwood Tripod
Altazimuth Yoke Mount
5mm, 20mm focal length - Eyepieces
Diagonal Mirror, 3x Barlow Lens, Erecting Lens
5 x 24mm Finderscope w/focus adjustment, Accessory Tray
Hardware Pack:
Tripod leg: 3-2_"bolts, 6-
Accessory tray: 3-_" bolts, 6-_" washers and 3-wingnuts
Tripod Leg Lock Screws: 3 pc.

TELESCOPE ASSEMBLY

Remove all components from the carton and identify all components. READ THROUGH ASSEMBLY
1.
INSTRUCTION BEFORE YOU ASSEMBLE YOUR TELESCOPE
2. Set-Up Tripod, Mount and Accessory Tray
Select one
Tripod Leg (5)
included in the hardware pack, insert the
Tighten the
Leg.
remaining two legs.
Locate the
Altazimuth Yoke Mount (3). Note: Before assembling tripod legs
to Altazimuth Yoke Mount, make sure the Accessory Tray Braces(7) face
Locate the long bolts and washers from the hardware pack.
inward.
Position the mount over the
holes in the
Tripod Leg
through the holes at the top of a
positioned on both outer sides of the
the bolt, but do not tighten it all the way. Repeat on the remaining two
. Once you have attached all
Tripod Legs
securely tighten all wing nuts.
Locate the
Accessory Tray (8).
and washers
to the
Tray Accessory Tray Braces (7).
be positioned beneath the
attached as some adjustments may be required.
1. Attach Telescope and Finderscope
Locate
Telescope Main Tube (2).
Yoke Mount (3)
the telescope between yoke. Carefully replace the
and remove lens cover from
Knobs
Locate the
Finderscope(16)
Remove the two nuts located near the back of the
(13).
and place the
Main Tube (2)
the exposed screws. Replace the nuts, and securely tighten the
Finderscope Mount
1. Attach Eyepiece and Diagonal Mirror
Locate an
Eyepiece (12)
Attach the
Mirror (11).
Your Bushnell Telescope is now ready to be used. To obtain the fullest
enjoyment from your telescope, please refer to the additional information below.
washers and 3-wingnuts
11
/16
and extend the
Tripod Leg Lock Screws
Tripod Leg (5)
with the holes in the mount. Insert the bolts
Using the accessory tray bolts, wingnuts
( 3-_" bolts, 6-_ washers and 3 - wingnuts)
Accessory Tray.
Secure telescope to
by removing
Altitude Lock Knobs (17)
60mm Objective Lens (1)
with pre-assembled
Finderscope
in place.
(either the 5mm or 20mm) and
Diagonal Mirror
Tripod Leg Middle Section (6).
Tripod Leg Lock Screw
so that the middle section is securely in place. Repeat on
as shown and align the
(fig. 1).
A washer should be
Tripod Leg.
Attach a wing nut to
Tripod Leg.
to the mount,
Tripod Legs
connect the
Start with one
Tripod Leg
Do not tighten wingnuts until all
Altazimuth
and positioning
Altitude Lock
Finderscope Mount
Telescope
and assembly over
Mount
as shown Insert an
(fig. 2).
Using
Tripod Leg Lock Screws (9)
into the lower brackets on the
Accessory
and attach wingnut. Wingnuts should
Accessory Tray Braces
10
Diagonal
into the
Eyepiece
Tripod
fig. 1
are
12
11
fig 2.
Diagonal Mirror.