Related Manuals for Sony LMD-X3200MD
Summary of Contents for Sony LMD-X3200MD
- Page 1 5-011-178-11(1) 2020-07 LCD Monitor Instructions for Use Before operating the unit, please read this manual thoroughly and retain it for future reference. LMD-X3200MD © 2020 Sony Corporation...
- Page 2 Indications for Use/Intended Use Symbols on the product The LCD Monitor is intended to provide 4K 2D color video displays of surgical and other medical Safety sign images. Follow the warnings in the instructions for use for parts of the unit on which this Notes symbol appears.
- Page 3 15 of FCC Rules. connector. If you have any questions about this product, you DC output may call; This symbol indicates the DC output Sony Customer Information Service Center 1-800- connector. 222-7669 or http://www.sony.com/ Supplier’s Declaration of Conformity Trade Name : SONY...
- Page 4 IEC 60601-1 standards. If in doubt, consult qualified Sony service personnel. 3. Connecting the unit to other devices may increase the leakage current.
- Page 5 • Portable RF communications equipment should be used no closer than 30 cm (12 inches) to any part of the LMD-X3200MD. Otherwise, degradation of the performance of this equipment could result. • If the LMD-X3200MD will be used adjacent to or stacked with other equipment, normal operation of the LMD-X3200MD under such configurations should be verified via observation.
- Page 6 Guidance and manufacturer’s declaration – electromagnetic immunity The LMD-X3200MD is intended for use in the electromagnetic environment specified below. The customer or the user of the LMD-X3200MD should assure that it is used in such an environment. Compliance level IEC 60601 Electromagnetic environment –...
- Page 7 Guidance and manufacturer’s declaration – electromagnetic immunity The LMD-X3200MD is intended for use in the electromagnetic environment specified below. The customer or the user of the LMD-X3200MD should assure that it is used in such an environment. IEC 60601 Compliance Immunity test Electromagnetic environment –...
- Page 8 If the measured field strength in the location in which the LMD-X3200MD is used exceeds the applicable RF compliance level above, the LMD-X3200MD should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the LMD- X3200MD.
- Page 9 The LMD-X3200MD is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. Portable RF communications equipment should be used no closer than 30 cm (12 inches) to any part of the LMD-X3200MD. Otherwise, degradation of the performance of this equipment could result.
- Page 10 When you dispose of the unit or accessories, you This product has been manufactured by or on must obey the laws in the relative area or country behalf of Sony Corporation, 1-7-1 Konan Minato-ku and the regulations in the relative hospital Tokyo, 108-0075 Japan.
- Page 11 For assistance, contact Sony qualified personnel. This symbol and its variations indicate that this product and its components, consumables, parts or spares thereof shall not be treated as household waste and may not be dropped in garbage bins.
- Page 12 SONY LIMITED WARRANTY - Please visit http://www.sonybiz.ca/pro/lang/en/ca/ article/resources-warranty for important information and complete terms and conditions of Sony’s limited warranty applicable to this product. For the customers in Europe Sony Professional Solutions Europe - Standard Warranty and Exceptions on Standard Warranty.
-
Page 13: Table Of Contents
Specifications ..........34 Table of Contents Dimensions ............40 Licenses ............41 Precaution ............14 On Safety ..........14 On Installation .......... 14 Precautions for using this unit safely ..14 Precautions for connecting this unit with other medical devices ......14 To prolong the life of the unit .... -
Page 14: Precaution
Some people may experience discomfort (such NETWORK as eye strain, fatigue, or nausea) while watching video images. Sony recommends – connection of the PEMS to an IT-NETWORK that that all viewers take regular breaks while includes other equipment could result in watching video images. -
Page 15: On Simultaneous Use With An Electrosurgical Knife, Etc
changes in the IT-NETWORK configuration; the physical characteristics of the liquid crystal connection of additional items to the IT- display, such “stuck” pixels may appear NETWORK; spontaneously. These problems are not a disconnecting items from the IT-NETWORK; malfunction. ... -
Page 16: On Fan Error
A material that withstands disinfection is used fan error indication appears on the screen, turn for the front protection plate of the medical use off the power and contact an authorized Sony LCD monitor. The protection plate surface is dealer. -
Page 17: On Repacking
This function sharpens images by adjusting color, contrast, and visibility of the dark area. You can select the mode best suited for the resolution of the equipment used. 1) A.I.M.E. is a registered trademark of Sony Corporation. Control panel Assigns functions frequently used during an operation to buttons on the front surface of the monitor. -
Page 18: Location And Function Of Parts And Controls
Location and Function of Parts and Controls Front Panel Power indicator When you press PORT A or PORT B when it is lit in white, an image from the input Indicator Operating State connector assigned to the PORT A/B is displayed. -
Page 19: Input Signals And Adjustable/Setting Items
The following functions are assigned in the Press again to hide the menu. /// buttons default setting. CUSTOM 1: Brightness Press to select the items and setting values. CUSTOM 2: Contrast CONTROL button CUSTOM 3: Flip Pattern Displays or hides the operation buttons on the ... -
Page 20: Rear Panel
Rear Panel To use the connectors on the rear panel, remove the cable cover. For details on the cable cover, see page 23. Cable cover (M) Cable cover (L) When connecting or disconnecting the cable of This cover is specifically for the 12G-SDI input/ the connector on the rear panel, remove this output connector. - Page 21 (non-shielded type of category 5 or more, digital component signals (4K/HD). optional). 3G-SDI input/output connector (BNC type) Note input connector (SDI2(HD)) Consult with Sony qualified personnel at using Input connector for serial digital component this connector. signals (HD). output connector (SDI2(HD)) Caution...
- Page 22 REMOTE connector (Stereo mini jack) The monitor can be operated partially by An SDI signal is output from the output connecting the optional Foot Switch FS-24. connector only when the monitor is turned on. 12V 2.5A (DC output) connector When the monitor is turned off, the signal is Outputs 12 volts for connected external not output from the output connector.
-
Page 23: Preparation
Note Avoid plugging the AC power cord into the AC input connector while connecting the optional AC power cord Sony AC adaptor (AC-300MD) to the DC input connector. Plug holder for the supplied AC Make sure that the (On)/... -
Page 24: Turning On The Monitor/Switching Input Settings
power cord and insert it until the fixing lever locks. When using the AC adaptor, insert the Caution DC connector into the monitor until it locks. Otherwise, the cable may fall out and the This unit with the cable covers attached image may disappear. -
Page 25: Initial Setting
French) for display on the menu and other on- Initial Setting screen displays. The default menu language is set to “English.” On the Language Setting screen, press the When you turn on the unit for the first time after or ... -
Page 26: Using The Menu
Using the Menu The unit is equipped with an on-screen menu for making various adjustments and settings such as picture control, input setting, setting change, etc. For changing the display language, refer to “Language” (page 31) in the System Configuration menu. Press the /... -
Page 27: Adjustment Using The Menus
About the control navigation Adjustment Using the Menus Depending on the state, the operation buttons of the unit light as shown below: White light: Operable state. Green light: Operating state. Items Off: Unable to operate. The screen menu of this monitor consists of the following items. -
Page 28: Adjusting And Changing The Settings
AUX IN Setting Menu Setting Power Supply Phase Adjusts color tones. The higher the Auto Input Select setting, the more greenish the picture. The lower the setting, the more purplish the picture. System Configuration (page 30) Chroma Adjusts color intensity. The higher the Control Lock setting, the greater the intensity. -
Page 29: Screen Control Menu
To display the corresponding signal with “Enhanced Format,” use a Screen Control menu Premium High-Speed HDMI cable The Screen Control menu is used to set the image within a length of 3 meters (Sony product recommended). display setting for each input. Menu Setting... -
Page 30: System Configuration Menu
Menu Setting Menu Setting Color Space Select the color gamut from “Auto,” Notes “BT.709,” or “BT.2020.” When “Auto” is selected, the color When “Auto Input Select” is set gamut changes according to the to “On,” if a signal is input to resolution set in “Format.”... - Page 31 Menu Setting Menu Setting OSD Setting Language You can select the menu or message language from the following Menu Position Sets the screen position for the OSD languages. menu. English: English Status Display Select Port, Input Connector Name, : Chinese Control Lock, Signal Format, Scan Size, ...
-
Page 32: Initial Setup Menu
Initial Setup menu Menu Setting The Initial Setup menu is used to make the basic Remote settings to use the unit. Remote Mode Sets the remote function when the REMOTE connector is connected to the optional Foot Switch FS-24. Menu Setting ... -
Page 33: Preset Menu
Menu Setting Troubleshooting Auto Input Select Off: The Auto Input Select function does not operate. For details, see page This section may help you isolate the cause of a problem and as a result, eliminate the need to Gives priority to PORT A and switches the port automatically. -
Page 34: Error Messages
Error Messages Specifications Picture performance When the following messages appear on the screen, turn off the power and contact an LCD panel TFT Active Matrix authorized Sony dealer. Pixel efficiency 99.99% Messages Description Viewing angle (panel specification) Fan Error A malfunction occurs in the fan. - Page 35 Information for Customers in WARRANTY, OR FOR ANY OTHER REASON Europe (1) WHATSOEVER. Screws for the VESA mount, M4 × SONY WILL NOT BE LIABLE FOR CLAIMS OF 12 mm (4) ANY KIND MADE BY USERS OF THIS UNIT OR Optional accessories MADE BY THIRD PARTIES.
- Page 36 Pin assignment 12V 2.5A (DC output) connector SERIAL REMOTE (RS-232C) connector D-sub 9-pin, female Pin number Signal Pin number Signal 12 V REMOTE (stereo mini jack) connector Pin number Signal On (short to sleeve) Off (open) 5V 2.0A (DC output) connector Pin number Signal...
- Page 37 Available signal formats The unit is compatible with the signal systems shown below: Signal format 12G-SDI 1 3G-SDI SDI Single Link SD-SDI 720×487/59.94i 4 : 2 : 2 YCbCr 10bit × 720×576/50i 4 : 2 : 2 YCbCr 10bit ×...
- Page 38 Signal format Display Port HDMI 4 : 4 : 4 RGB 10bit/8bit × 4 : 4 : 4 YCbCr 10bit/8bit 720×576/50p × × 4 : 2 : 2 YCbCr 12bit 4 : 4 : 4 RGB 10bit/8bit ...
- Page 39 Signal format Display Port HDMI × 4 : 4 : 4 RGB 10bit/8bit 4 : 4 : 4 YCbCr 10bit/8bit × 4096×2160/25p × × 4 : 2 : 2 YCbCr 12bit 800×600/60p 4 : 4 : 4 RGB 10bit/8bit ...
-
Page 40: Dimensions
Approx. 11.8 kg (26 lb 1 oz) (when the optional stand is not installed) Unit: mm (inches) AC adaptor (optional) Rear (VESA Mount Instruction) (Sony’s AC adaptor AC-300MD) Unit: mm (inches) * Length of M4 screws (4) Attached object Monitor cabinet... -
Page 41: Licenses
Licenses For details on the license, refer to “Software License Information” on the CD-ROM.