Jacuzzi J-200 Instructions For Preinstallation page 32

I
Periodically, however, the differential switch (see "ELECTRICAL
SAFETY" chapter) of the system to which the mini-pool is connect-
ed must be checked for efficiency. When you press the TEST key,
the switch must disconnect. If this does not happen, discon-
nect the power supply immediately and contact a qualified
technician.
I
For any extra maintenance and/or repairs it is recommended
that you contact an Authorized Service Centre and use only origi-
nal spare parts.
Set up for installation
The customer must make provisions for a ground drainage point
of suitable dimensions and that can be inspected for any cleaning
that may be required.
ATTENTION: Before preparing the ground drainage
point, consult the local authority for the regulations that
control the drainage of chemically treated water.
J-200
I
The spa water drain is located behind the front panel, to the
right (or left), dependent on the electric box. The pipe must be
placed in the drain basin when carrying out periodic emptying.
i
1-1a-1b-1c, part.A.
The pipe must be placed in the drain basin when carrying out
periodic emptying.
J-300/J-LXL/J-400/J-500
I
Premium spas are equipped with the drain arranged as in
2-2a-2b-2c-2d-2e-2f-2g-2h, 3-3a-3b-3c, , 4-4a part.A.
For periodic emptying of the spa you can connect a rubber hose
i
to the drain valve ( 2-2a-2b-2c-2d-2e-2f-2g-2h, 3-3a-3b-3c,
4-4a part.A).
NOTE: To open the valve, turn the ring nut counter-clockwise and pull.
If you decide to attach the spa to the drain, it is advisable to connect
upstream from the valve (for greater flow capacity) and to install a
shutter valve near the drain in an accessible area (
2e-2f-2g-2h, 3-3a-3b-3c, 4-4a part.A1.
J-400/J-500
i
I
The Quick Drain™ (
nected to the drain pit.
I
According to the type of installation chosen the ground
drainage point will then be put into position.
can be installed in a variety of ways:
- Free standing on the floor or on a specifically prepared base
i
( 9).
- Semi-built in, so that only the base of the spa is built-in and
therefore the side cover panels remain free (
it is appropriate to prepare some removable under-frames (in
marine plywood, etc.) that, besides aesthetically completing in-
stallation, allow the panels to be removed more easily.
i
2-2a-2b-2c-2d-
3-3a-3b-3c, 4-4a part.C) may be con-
The Premium spas
i
10). In this case,
I
In any case you will need to provide a support base that is suit-
able for the selected model, taking into consideration the data
contained in the table "Weights".
I
You can use a garden hose to fill the spa.
If the spa is connected, for periodic filling, to the mains
system that supplies drinking water, this connection
must be carried out in compliance with the EN1717
norm, using "AA", "AB" or "AD" anti-pollution protection
procedures. For further information, we recommend you
contact your water supply company and/or your
plumber.
I
For indoor installation, it is necessary to remember that water
evaporation from the spa (especially where high temperatures are
involved) can cause very high levels of humidity. Natural or forced
ventilation helps to maintain personal comfort and reduce dam-
age to the building due to humidity.
Jacuzzi Europe refuses all responsibility for any damage caused by ex-
cessive humidity or by overflowing water. Consult a specialist for in-
door installation.
I
Remember that it is compulsory to install a multiple-pole sec-
tion switch with characteristics that are not less than the ones
given in the chapter "Electrical safety" and
I
The installer must use cables with an adequate cross-section,
protected by a sheath and/or with tubes or ducts, with character-
istics not inferior to type H 05 VV-F.
The entry of cables into the mini-pool up to the electrical box (
i
5-6-7) must be provided at point B or B1, depending on the cus-
tomer's installation needs.
Note: The lead sections must take account not only the sys-
tems absorption but also the cable path and the distances,
the chosen protection systems and the specific regulations for
fixed electrical systems in force in the country where the spa
is installed.
I
The installer must comply with the above regulations, and also
use watertight connectors at connection points. He must also
guarantee compliance with the specific current standards for
systems in the country in which the spa is installed.
It is mandatory to comply with this instruction. Any other procedure
is prohibited.
32
i
5-6-7.
i