Cleaning The Outer Casing - Garmin NMEA 0183 Installation Instructions Manual

Item Description
Power source
Garmin NMEA 0183 compatible chartplotter
GPS 19x Color
wire
Red
Black
White/Orange
(ground)
White
Gray
White/Red
(unconnected)
Orange
NMEA 0183 Connection Exceptions
The orange accessory on wire is used when connecting the
antenna to a Garmin chartplotter, or other NMEA 0183 device
that has a defined accessory signal wire. If you are connecting
the antenna to a device that does not have an accessory signal
wire, connect the orange wire from the antenna to ground and
connect the antenna power wire to the ignition or install an in-
line switch. The antenna will drain the battery of the boat if it is
not switched.
• If your NMEA 0183 compliant device has only one receiving
wire (Rx), connect it to the gray wire (Tx/A (Out +)) from the
antenna, and leave the white/red wire (Tx/B (Out -)) from the
antenna unconnected.
• If your NMEA 0183 compliant device has only one
transmitting wire (Tx), connect it to the white wire (Rx/A (In
+)) from the antenna, and connect the white/orange wire
(Rx/B (In -)) from the antenna to ground.
Limiting the Antenna Update Rate
By default, the antenna outputs position data updates 10 times
per second using serial communications rate of 38400 bps. By
installing the included resistor cable, the antenna can be limited
to output position updates once per second using serial
communications rate of 4800 bps.
1
Mount the antenna according to these instructions
the Antenna, page 1).
2
If necessary, cut the cable to the appropriate length for the
installation.
3
Solder the included Update Rate Select cable to the orange
Accessory on wire.
4
Use the heat-shrink tubing around the soldered connections.
5
If you have not connected the antenna already, connect the
power and data cable (NMEA 0183 Wiring for Two-Way
Communication, page 3).

Cleaning the Outer Casing

Avoid chemical cleaners and solvents that can damage plastic
components.
1
Clean the outer casing of the device using a cloth dampened
with a mild detergent solution.
2 Wipe the device dry.
4
Chartplotter Chartplotter wire
wire function
Power (+)
Ground (-)
Tx/B (Out -)
Tx/A (Out +)
Rx/A (In +)
Rx/B (In -)
Accessory on
CAUTION
(Mounting
NOTICE
Appendix
Software Update
You must update the Garmin chartplotter software when you
install this device. For instructions on updating the software, see
your chartplotter owner's manual at support.garmin.com.
Specifications
Dimensions (diameter x
height)
Weight
Cable length
Temperature range
Case material
Water rating
Compass-safe distance
Power input source
Input current
Battery Notice
Contact your local waste disposal department to dispose of the
device/batteries in accordance with applicable local laws and
regulations.
Declaration of Conformity
Hereby, Garmin declares that this product is in compliance with
the Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
garmin.com/compliance.
Innovation, Science and Economic Development
Canada Compliance
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic
Development Canada's licence-exempt RSS(s). Operation is
subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of the device.
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and may cause harmful interference to
radio communications if not installed and used in accordance
with the instructions. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
1
The device withstands incidental exposure to water of up to 1 m for up to 30 min.
For more information, go to www.garmin.com/waterrating.
19 15
91.6 × 49.5 mm ( 3 / × 1
32
201 g (7.1 oz.)
9.14 m (30 ft.)
From -30° to 80°C (from -22° to 176°F)
Fully gasketed, high-impact plastic alloy
1
IEC 60529 IPX7
150 mm (5.9 in.)
8 to 33 Vdc, unregulated
40 mA @ 12 Vdc
NOTICE
/ in.)
16