Garmin GPS 19x NMEA 0183 Installation Instructions Manual
Hide thumbs
Also See for GPS 19x NMEA 0183:
- Installation instructions manual (48 pages) ,
- Installation instructions manual (6 pages) ,
- Installation instructions manual (19 pages)
Advertisement
Quick Links
GPS 19x NMEA 0183
Installation Instructions
CAutIoN
Always wear safety goggles, ear protection, and a
dust mask when drilling, cutting, or sanding.
Notice
When drilling or cutting, always check what is on the
opposite side of the surface.
The Garmin GPS 19x NMEA 0183 HVS high-
sensitivity GPS antenna provides position information
over NMEA 0183. The GPS 19x NMEA 0183 HVS
can be connected to a Garmin chartplotter or another
NMEA 0183-compliant device.
The antenna must be properly installed according
to these instructions. You need the appropriate
fasteners, tools, and mounts listed in each section.
These items are available at most marine dealers.
NotE: When connecting this antenna to a GPSMAP
2000, 3000, 4000, or 5000 series device, you must
limit the update rate. If the update rate is not limited,
the chartplotter might not receive and display the
GPS signal properly.
Registering the Device
• Keep the original sales receipt, or a photocopy, in
a safe place.
For future reference, write the serial number
assigned to your antenna in the space provided. It is
located on a sticker on the back of the antenna.
Serial number
tools Needed
• Drill
•
/
in. (3.2 mm) drill bit
1
8
•
/
in. (19 mm) drill bit for a pole-mount cable-hole
3
4
• 1 in. (25 mm) hole saw for a surface-mount cable-
hole
• Screwdriver, appropriate for the screw type
• Countersink bit for mounting on fiberglass
• Marine sealant for some mounting options
• Solder and shrink wrap
◦ Needed for all wiring connections
◦ Specifically needed when limiting the antenna
to 1 Hz
optional Accessories
• Screws, for under-deck mounting
Mounting type and Location
Considerations
You can mount the antenna on a flat surface,
attach it to a standard 1 in. OD, 14 threads per in.,
pipe-threaded pole (not included), or install it under
fiberglass.
For optimal performance, consider these guidelines
when selecting the antenna mounting location.
• The antenna must be mounted 5.9 in. (150 mm)
from a compass to avoid interference.
• To ensure the best reception, the antenna
should be mounted in a location that has a clear,
unobstructed view of the sky in all directions
➊
• The antenna should not be mounted where it is
shaded by the superstructure of the boat
radome antenna, or the mast.
• The antenna should not be mounted near the
engine or other sources of Electromagnetic
Interference (EMI)
• If a radar is present, it is best to install the
antenna above the path of the radar
is acceptable to install it below the path of the
radar
if necessary. The antenna should not be
➎
installed directly in the path of the radar
• The antenna should be mounted at least 3 ft.
(1 m) away from (preferably above) the path of a
radar beam or a VHF radio antenna
• On a sailboat, to prevent inaccurate speed
readings caused by excessive heeling, the
antenna should not be mounted high on the
mast.
• The antenna provides more-stable readings
when located nearer to water level.
testing the Mounting Location
1
Temporarily secure the antenna in the preferred
mounting location and test it for correct operation.
2
If you experience interference with other
electronics, move the antenna to a different
location, and test it again.
3
Repeat steps 1–2 until you can verify that the
antenna operates correctly.
4
Permanently mount the antenna.
Surface-Mounting the Antenna
Before you permanently mount the antenna, test
the mounting location for correct operation.
Use the surface-mount bracket
template.
.
➊
➋
➌
.
➌
➍
➍
➏
➎
➐
➐
as your mounting
➊
➊
➍
➋
➌
, a
➋
, though it
.
➏
.
➎
Advertisement
Related Manuals for Garmin GPS 19x NMEA 0183
Summary of Contents for Garmin GPS 19x NMEA 0183
-
Page 1: Installation Instructions
GPS 19x NMEA 0183 Installation Instructions CAutIoN ➊ ➋ ➌ Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. Notice When drilling or cutting, always check what is on the opposite side of the surface. • The antenna should not be mounted where it is The Garmin GPS 19x NMEA 0183 HVS high- shaded by the superstructure of the boat , a ➋ sensitivity GPS antenna provides position information radome antenna, or the mast. over NMEA 0183. The GPS 19x NMEA 0183 HVS • The antenna should not be mounted near the can be connected to a Garmin chartplotter or another engine or other sources of Electromagnetic NMEA 0183-compliant device. Interference (EMI) ➌ The antenna must be properly installed according to these instructions. You need the appropriate • If a radar is present, it is best to install the fasteners, tools, and mounts listed in each section. antenna above the path of the radar , though it ➍... - Page 2 Use a pencil to mark the three screw locations Route the cable away from sources of electronic and to trace the cable-hole in the center of the interference, and connect it to power and to bracket. a NMEA 0183-compliant device. Set the surface-mount bracket aside. Mounting the Antenna with the Cable Do not drill through the surface-mount bracket. Routed through the Pole Drill the three in. (3.2 mm) pilot holes. Position a standard 1 in. OD, 14 threads per in., NotE: If you are mounting the GPS 19x pipe-threaded pole (not included) in the selected on fiberglass, it is recommended to use a location, and mark the approximate center of the countersink bit to drill a clearance counterbore pole. through the top gelcoat layer (but no deeper). Drill a hole using a in. (19 mm) drill bit for the This will help to avoid cracking in the gelcoat cable to pass through. layer when the screws are tightened. Fasten the pole to the boat. Use a 1 in. (25 mm) hole saw to cut the cable Thread the pole-mount adapter onto the pole. hole in the center. Do not overtighten the adapter. Place the seal pad on the bottom of the ➋...
- Page 3 White/Orange Rx B(-) ➏ ➐ Purple Pulse per second (PPS) > ➐ ➑ ➑ ➊ ➑ Pin 1 ➊ Pin 8 ➑ Examples connecting the Antenna to a Garmin chartplotter ➌ ➊ ➑ ➋ ➋ ➒ ➊ ➍ > ➌ > > ➓ ➍ > >...
-
Page 4: Care Information
Device Wire GPS 19x antenna ➊ Power (+) ➊ ➑ 1A fuse ➋ Black Ground (-) ➋ ➒ 12 Vdc battery ➌ Orange Accessory-ON ➌ ➓ Garmin NMEA 0183-compatible ➍ chartplotter Gray Rx A (+) ➍ White/Red Rx B (-) ➎ White Tx A (+) ➏ White/Orange Tx B (-) ➐ Chartplotter Software NMeA 0183 connection exceptions CAutIoN To ensure compatibility with the antenna, upgrade ... -
Page 5: Declaration Of Conformity
Water Immersion You acknowledge that the Software is the property of Garmin and is protected under the United States of The device is waterproof to IEC Standard 60529 America copyright laws and international copyright IPX7. It can withstand immersion in 1 meter of water treaties. You further acknowledge that the structure, for 30 minutes. Prolonged submersion can cause organization, and code of the Software are valuable damage to the unit. After submersion, be certain to trade secrets of Garmin and that the Software in wipe and air dry the unit before reuse. source code form remains a valuable trade secret of Declaration of Conformity Garmin. You agree not to decompile, disassemble, modify, reverse assemble, reverse engineer, or Hereby, Garmin, declares that this product is in reduce to human readable form the Software or any compliance with the essential requirements and part thereof or create any derivative works based on other relevant provisions of Directive 1999/5/EC. the Software. You agree not to export or re-export Industry Canada Compliance the Software to any country in violation of the export Category I radiocommunication devices comply with control laws of the United States of America. Industry Canada Standard RSS-210. Category II Limited Warranty radiocommunication devices comply with Industry This Garmin product is warranted to be free from Canada Standard RSS-310. This device complies defects in materials or workmanship for one year with Industry Canada license-exempt RSS from the date of purchase. Within this period, standard(s). Operation is subject to the following two... - Page 6 Auction Purchases: Products purchased through online auctions are not eligible for warranty coverage. Online auction confirmations are not accepted for warranty verification. To obtain warranty service, an original or copy of the sales receipt from the original retailer is required. Garmin will not replace missing components from any package purchased through an online auction. International Purchases: A separate warranty may be provided by international distributors for devices purchased outside the United States depending on the country. If applicable, this warranty is provided by the local in-country distributor and this distributor provides local service for your device. Distributor warranties are only valid in the area of intended distribution. Devices purchased in the United States or Canada must be returned to the Garmin service center in the United Kingdom, the United States, Canada, or Taiwan for service. Australian Purchases: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits under our Limited Warranty are in addition to other rights and remedies under applicable law in relation to the products. Shop for quality Garmin products on our website.