Table of Contents
Advertisement
Quick Links
Use these instructions to install the Garmin
of this package with the packing list on the box. If any pieces are missing, contact your Garmin dealer immediately.
Use the following instructions to install the AIS 300 device. Details for the following steps are included in this document:
1. Select locations for the AIS components.
2. Mount the AIS 300 receiver box.
3. Connect the AIS 300 to power.
4. Connect the AIS 300 to a VHF antenna and to an optional VHF radio (page 4).
5. Connect the AIS 300 to a NMEA 2000 network or to a NMEA 0183-compatible chartplotter (optional - page 4).
When navigating, carefully compare information provided by the unit to all available navigation sources, including information from visual
sightings, local waterway rules and restrictions, and maps. For safety, always resolve any discrepancies or questions before continuing
navigation.
Use this unit only as a navigational aid. Do not attempt to use the unit for any purpose requiring precise measurement of direction, distance,
location, or topography.
This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or
reproductive harm. This Notice is provided in accordance with California's Proposition 65. See
information.
Wear safety goggles and a dust mask when drilling, cutting, or sanding.
Safe Compass Distance
Ensure that you install the AIS 300 receiver box at least 15
correctly when the AIS 300 is operating.
Selecting Locations for the AIS 300 Components
Use the wiring layout diagrams starting on
cables reach all components before permanently mounting any component.
Mounting the AIS 300 Receiver Box
Install the AIS 300 receiver box below deck on a bulkhead. Select a location that is dry and protected from washdown. Ensure that the
location is well ventilated and away from objects that generate heat. Ensure that the receiver box is at least 15
compass to avoid interference.
Needed tools
•
Drill and drill bits
•
Number 2 Phillips screwdriver
to mount the receiver box:
1. Ensure that the chosen location is dry, protected from washdown, and well-ventilated.
2. Use the receiver box as a template, and use a pencil to mark the holes in the four corners. Do not drill through the receiver box.
3. Drill four
/
in. (3 mm) pilot holes.
1
8
4. Mount the receiver box using the included 20 mm M 3.5 screws. You can also use bolts, washers, and nuts (not included) to mount the
receiver box if the mounting surface is suitable.
March 2010
AIS 300 Installation Instructions
AIS 300 Automatic Identification System (AIS) Class B receiver device. Compare the contents
®
WARNING
CAutIoN
/
in. (40 cm) from any compass. Test your compass to verify that it operates
3
4
page 2
to determine how to best organize the AIS 300 components on your boat. Ensure that the
190-01178-00 Rev. B
www.garmin.com/prop65
for more
/
in. (40 cm) from any
3
4
Printed in China
Advertisement
Table of Contents
Related Manuals for Garmin 190-01178-00
Summary of Contents for Garmin 190-01178-00
- Page 1 Use these instructions to install the Garmin of this package with the packing list on the box. If any pieces are missing, contact your Garmin dealer immediately. Use the following instructions to install the AIS 300 device. Details for the following steps are included in this document: 1. Select locations for the AIS components.
- Page 2 AIS 300 Wiring Layout: AIS 300 Connected to a Garmin Chartplotter through NMEA 2000 AIS 300 receiver box RF cable to VHF antenna (not included) NMEA 000 drop cable (included) RF interconnect cable (included) VHF radio* (optional - not included) Chartplotter power Chartplotter (optional - not included) 1 or 4 Vdc * The AIS 300 does not need to be installed alongside a VHF radio, but they can share the same VHF antenna if they are both installed on your boat. AIS 300 Installation Instructions...
- Page 3 AIS 300 Wiring Layout: AIS 300 Connected to a Garmin Chartplotter through NMEA 0183 AIS 300 receiver box RF interconnect cable (included) * The AIS 300 does not need to be installed alongside a VHF radio, but they can share the same VHF antenna if they are both installed on your boat. ** The listed wire colors are for the NMEA 0183 Port 1 input on a Garmin GPSMAP 4000/5000 or GPSMAP 6000/7000 series chartplotter. Refer to the installation instructions provided with your Garmin chartplotter if you want to connect the AIS 300 to a different model of Garmin chartplotter or to a different NMEA 0183 port on a GPSMAP 4000/5000 or GPSMAP 6000/7000 series chartplotter. If you are connecting the AIS 300 to a non-garmin chartplotter, see page 5 for detailed wiring assignments. AIS 300 Installation Instructions VHF radio* (optional - not included) Wire color [function] Gray [Tx A (+)] > Pink [Tx B (-)] > Yellow [power toggle] Chartplotter power 1 or 4 Vdc Wire color [function]** White [Rx A (+)] >...
- Page 4 Accessory On wire from the chartplotter. The AIS 300 will then turn on or off with the Garmin chartplotter. • If the AIS 300 is connected to a non-Garmin NMEA 0183 chartplotter, or not connected to a chartplotter at all, then you must install a toggle switch to turn the device on and off.
- Page 5 NMEA 0183 bare wires to a Garmin chartplotter as indicated in the wiring layout diagram on the AIS 300 to a non-Garmin chartplotter. Use 22 AWG wire for extended runs of NMEA 0183 wire, if needed. If it is necessary to extend the power wires, use 16 AWG or larger wire.
-
Page 6: Specifications
When connected to a NMEA 0183 device, the AIS 300 transmits the VDM sentence. Product Registration Help us better support you by completing our online registration today. Go to http://my.garmin.com. Keep the original sales receipt, or a photocopy, in a safe place. -
Page 7: Industry Canada Compliance
Limited Warranty This Garmin product is warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, Garmin will, at its sole option, repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost. - Page 8 Distributor warranties are only valid in the area of intended distribution. Devices purchased in the United States or Canada must be returned to the Garmin service center in the United Kingdom, the United States, Canada, or Taiwan for service.