1. Manuals
  2. Brands
  3. Audiovox Manuals
  4. Automobile Accessories
  5. Microcruise IV
  6. Installation and owner's manual

Audiovox Microcruise IV Installation And Owner's Manual

Cruise control
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
i':-:"~;:
'::-.;;J
.~
'J
K
"
t
.l
~
!
:
{
}
,
.;::;"::1
FORM
:."
":
~
# 2756
Rev.
B
10/98

Advertisement

Table of Contents
loading

Related Manuals for Audiovox Microcruise IV

Summary of Contents for Audiovox Microcruise IV

  • Page 1 i':-:"~;: '::-.;;J " .;::;"::1 :." ": FORM # 2756 Rev. 10/98...
  • Page 2 THIS This Cruise Control Kit is a microprocessor based Cruise Control. It is designed for ease of installation and can be used with most cars, light trucks and vans. Carefully follow the installation procedures in this manual for best results. DO NOT INSTALL HAS A MANUAL SWITCH...
  • Page 3 Parts List and Parts Diagram Helpful Hints Switch Settings Ill. Installation Throttle Servo Measuring Attaching Pedal Pulley Pulley Assembly Connection Procedures Attachment Assembly Assembly Cable Throttle Mounting Harness Anchoring Wiring Vacuum Sealing Cruise Tube Snap-In-Adapter General Throttle General Ford Attachments Control Bulkhead Clamp...

  • Page 4: Parts List

    PARTS LIST Disengagement Switch use 250-4206 , " Vacuum Reservoir use 250-3417 or 250-6019 ,',' Vacuum Regulator use 250-4115 *Order Kit 250-2213 and receive parts indi~~~.; " Form #2756, Page 4...
  • Page 5 " """'"",""c, "."."".",.,:,".-J,!22 ~~~-&~.~ ","-..I Form #2756, Page 5...
  • Page 6 'C" : '," II 1. Before Starting Installation: Familiarize yourself with the Installation Instructions and Cruise Control's components. If vehicle is equipped with an ANTI- rnEFf disconnecting battery cable. The c<xie must be re-entered wbtJI the negative battery cable is reinstalled. If vehicle is equipped with an AIR BAG.

  • Page 7: Programming Switches

    The Actuator Assembly must be programmed for the vehicle on which it is installed. The TEN (10) programming switches must be set according to the chart below in order for the Cruise Control to operate properly. NOTE I: Both the Gray (VSS) and the Blue (TACH) wires must be connected.
  • Page 8 r SERVO ASSEMBL I. NOTE: 00 NOT MOUNT SERVO ASSEMBLY IN nIB FOu.oWING a. Under the felKIcr b. U..r the vehicle c. DirectJyto the eDgiM or bi)llrhead d With cable JX)inted ckJwn e. Near sharp. bot or DMJViDg OOjects f. Near ignition coil (No clC*r g.
  • Page 9 MEASUIUNG THROTfLE " , Continued I. Make a mark on the throtde cable when the throttle is in the idle position. (Figure 3) 2. Depress aa:elerator ~ on the throttle cable when the throttle is in the wide open position. (Ficure 4) 3.
  • Page 10 A TT ACHING CABLE ASSEMBL This section will cover the proper ways to use the hardware available. Each section contains sample illustrations showing how the coMector is used in an actual installation. It must be noted however, that you should have an understanding of howeach attachment method works so that a proper installation is achieved.
  • Page 11 B. Pullev Assemblv mua/J UsinL-' the T-BAR ADAPTER (250-4184J I. Remove air cleaner to expose the dual pulley segments. 2. Find the blank anchor that is located above the throttle anchor. Follow the instructions in STEP B for Anchoring Cruise Cable -page IS. 3.

  • Page 12: Installation Procedures

    INST A TT ACHING CABLE ASSEMBL THROTTLE D. Ford Throttle I. Select a Tube Clamp that fits the throttle cable. Make sure the tabs of the Tube Clamp point away from the carburetor or air throttle, this will prevent the throttle from banging. (Figure 13) 2.
  • Page 13 2. Attach the Bead Chain to the Two Bead Connector. Secure beads by folding down the metal tabs. The following parts will be used when installed properly: Two Bead Connector, Bead Chain, Bead Chain Connector, and Bead Chain Connector Cover. 3.
  • Page 14 INST r Anchoring Cable Assembly There arc tJU'CC (3) types of comlectors used to anchor tJ1e Cable Assembly: A. Snap-In Adapter B. General Motors Blank Anchor C. Tube Clamp A. ~'nQIJ-ln AdaDter I. Before using the Snap-ln Adapter, remove tlte Adjustable Sleeve from the Cable Assembly.
  • Page 15 .8. General Motors Blank Anchor I. To locate the blank anchor on General Motors vehicles. it is necessary to remove the air cleaner. The blank anchor is located above the throttle anchor . 2. This anchor is hollow except at one end. Use a 114.
  • Page 16 Tube OalnD I. Before using the Tube Clamp slide tI)e Adjustable Sleeve into a 1<K:a'tiaR-oD the Cable Assembly so you can center the Tube Clamp to avoid slippage. (Figure 2. The Tube Clamp may be used to anchor the Cable Assembly to an exjsting throttle cable bracket.
  • Page 17 Suggested Vacuum Source Locations: a. Factory Installed Tee with removable cap (Figure 29) b. Manifold Vacuum Tree usually with an extra vacuum port with removable cap (Figure 30) c. Existing Vacuum Canister mounted on vehicle generally on the inner fenderwell or engine bulkhead (Figure 31) d.
  • Page 18 Harness Assembly I. Plug Bamess Assembly into Servo Assembly. Be sure to push Rubber Grommet securely into place. (Figure 35) Place cover onto the Servo Assembly and securely fasten screws. (Figure 36) 2. Straighten the Harness Assembly and find the 4 pin mating connectors. Separate the 4 pin connectors.

  • Page 19: Constant Power

    It,~,,;i ~ " .');.,., .",. -~:!'. I Cruise Control Switch '",,'-; ~~.;f~,\ If your Cruise Control switch is the type which clamps on the turn signal lever, requires cutting the turn signal lever, or is ~f'c;; mounted on ~ instrument panel, follow instructions ~~~Ji equipm~nt turn si~ lever, remove the existing lever and install the Cruise Control switch and lever assembly as instructed in...
  • Page 20 SELF Entering Diagnostics Mode: I. Turn the Cruise Control Switch to the OFF position 2. Turn the ignition switch to the OFF position 3. Press and hold the RESUME/ACCEL starting tIle eIIg;'.e. Now release the RESUMFJACCEL 250-3742 or 250-3743 Cruise Control Switch, turn the ignition switch to the ON position wit1lollt starting tIle engine, hold the RESUME/ACCEL 4.
  • Page 22 < « >-z > ---" ..J ..J IU ~ ..JOOe~ ~>OCIJ~ -JCO ~ ]:.~ x z. ..JO &I. &I. « :§I §~...

  • Page 23: Warranty

    This Warranty gives you specific legal rights and you may also have other rights which vary from state to state. IN EASTERN U.8.A.: AUDIOVOX CORPORA nON. 60 ARKA Y DRIVE. HAUPP AUGE. NEW YORK 11788 -(516) IN WESTERN U.8.A.: AUDIOVOX WEST CORPORAnON,...
  • Page 24 Be sure to road test your Cmisc Control indicated in this section. The Cnaile Control Follow the operating instructions to test drive operating correctly. ON/OFF: The first time you use the Cmisc should be on a straight, paved road away from Slide the ON/OFF switch of the Cnaile...

  • Page 25: Technical Service

    TECHNICAL In the event that you need technical assistance with trouble shooting, please h~ve the following information ready when calling our Technical Service Department 910-277-1828. This information is important for a proper and speedy diagnosis of the problems encountered. Model Number of Cruise Control System printed on box and DI8Dufacturen code printed on the Servo Assembly Vehicle Make Model and Year: Enline...

Table of Contents