Table of Contents
Advertisement
5)
Press as to select the input to be specified as the switching destination, and press the <ENTER>
button.
[OFF]
[HDMI]
[DVI-D]
[SDI]
[DIGITAL LINK]
[HDMI1 [SLOT]]
*2
[HDMI2 [SLOT]]
*2
[DVI-D1 [SLOT]]
*2
[DVI-D2 [SLOT]]
*2
[DisplayPort1 [SLOT]]
[DisplayPort2 [SLOT]]
[SDI1 [SLOT]]
*2
[SDI2 [SLOT]]
*2
[SDI3 [SLOT]]
*2
[SDI4 [SLOT]]
*2
[SDI OPT1 [SLOT]]
[SDI OPT2 [SLOT]]
*1 Individual input on the twisted-pair-cable transmitter or the DIGITAL LINK output supported device cannot be specified.
*2 This can be selected when the optional Interface Board equipped with corresponding input is installed in <SLOT>.
Note
f When the [PROJECTOR SETUP] menu → [NO SIGNAL SETTING] → [BACKUP INPUT SETTING] → [BACKUP INPUT MODE] is set to
anything other than [OFF], the secondary input switching function will not operate even when [SECONDARY INPUT] is set to anything other
than [OFF]. The backup input switching function is prioritized.
[BACK COLOR]
Set the display of the screen when a signal is not input.
1)
Press as to select [NO SIGNAL SETTING].
2)
Press the <ENTER> button.
f The [NO SIGNAL SETTING] screen is displayed.
3)
Press as to select [BACK COLOR].
4)
Press qw to switch the item.
f The items will switch each time you press the button.
[BLUE]
[BLACK]
[DEFAULT LOGO]
[USER LOGO]
Note
f The [BACK COLOR] setting item is common with the following menu item.
g The [DISPLAY OPTION] menu → [BACK COLOR]
f To create and register the [USER LOGO] image, use "Logo Transfer Software". The software can be downloaded from the Panasonic
website (https://panasonic.net/cns/projector/).
When transferring logos via the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G), setting for "NO
SIGNAL SLEEP" of the DIGITAL LINK output supported device should be set to "OFF" to avoid interruption of communication.
[NO SIGNAL LIGHTS-OUT]
This is a function to automatically turn off the light source of the projector when there is no input signal for specific
period. The time until the light source is turned off can be set.
1)
Press as to select [NO SIGNAL SETTING].
2)
Press the <ENTER> button.
f The [NO SIGNAL SETTING] screen is displayed.
Chapter 4 Settings — [PROJECTOR SETUP] menu
Disables the secondary input switching function.
Sets the secondary input to HDMI.
Sets the secondary input to DVI-D.
Sets the secondary input to SDI.
Sets the secondary input to DIGITAL LINK
Sets the secondary input to HDMI1 of the Interface Board.
Sets the secondary input to HDMI2 of the Interface Board.
Sets the secondary input to DVI-D1 of the Interface Board.
Sets the secondary input to DVI-D2 of the Interface Board.
Sets the secondary input to DisplayPort1 of the Interface Board.
*2
Sets the secondary input to DisplayPort2 of the Interface Board.
*2
Sets the secondary input to SDI1 of the Interface Board.
Sets the secondary input to SDI2 of the Interface Board.
Sets the secondary input to SDI3 of the Interface Board.
Sets the secondary input to SDI4 of the Interface Board.
Sets the secondary input to SDI OPT1 of the Interface Board.
*2
Sets the secondary input to SDI OPT2 of the Interface Board.
*2
Displays blue in the entire screen.
Displays black in the entire screen.
Displays the Panasonic logo in the screen.
Displays the image registered by the user in the screen.
.
*1
ENGLISH - 189
Advertisement
Table of Contents
