Toshiba TC-net Instruction Manual page 92

7. How to set the environment for OPC Server
Reading and writing action mode of TC-net items and OPC items in a simulation mode in the following.
The item that a Mode column is gray shows that an action is different from a normal mode.
Prefix Item Name
Tcnet ScanMode
ScanHealthyMap.Block#nnnn
ClearScanUnHealthyMap
ScanSendCycle.HScanCyc
ScanSendCycle.MScanCyc
ScanSendCycle.LScanCyc
ScanSendCycle.MaxNodeDist
ScanSendCycle.MaxRepeater
ScanSendCycle.LoopTotalExt
ScanSendCycle.MaxUtghJtgiDist
ScanTalkerBlock.HScan.Block#nnn
ScanTalkerBlock.MScan.Block#nnn
ScanTalkerBlock.LScan.Block#nnn
ScanTalkerMap.Block#nnnn
ClearScanTalkerMap
InringMap.Mac#nnn
StationInf.RegInf
StationInf.Mac#nnn.MacInf#d
ClearStationInf
DualInf#d
DualInf#1
DualInf#2
ClearDualInf
LinkControl
Version#d
Correspondence#d
SwitchConfig
HealthyCounter
RasInfo.Mac#mmm.ContFlag
RasInfo.Mac#mmm.HealthyCounter
RasInfo.Mac#mmm.Alarm
RasInfo.Mac#mmm.Slot#d.HealthyCounter
RasInfo.Mac#mmm.Slot#d.ContType
RasInfo.Mac#mmm.Slot#d.ContSubType
RasInfo.Mac#mmm.Slot#d.PhaseMode
RasInfo.Mac#mmm.Slot#d.Alarm
84
Table 7.1 List of OPC items (simulation mode)
Description
Item Name and Data Type are imported from nV Tool.
Scan running state / Start or Stop control
Scan healty map [#0000 - #2047
Clear scan healthy map
High scan transmission cycle
Middle scan transmission cycle
Low scan transmission cycle
Maximum distance between nodes
Maximum repeater steps
System total length (loop total length), Unit : 1km
Star maximum length, Unit : 0.1km
Scan talker block (High speed) [#000 - #064
Scan talker block (Middle speed) [#000 - #128
Scan talker block (Low speed) [#000 - #384
Scan talker map [#0000 - #2047
Clear duplicate blocks of scan talker block map
Inling map [#000 - #255]
Station information (Error counter)
Station information [Mac:#000 -#255, Diag:#0 -#3]
Clear station information
Network dual diagnosis counter [[#0, #3 - #6]
Network dual diagnosis counter (A Bus Normal Count)
Network dual diagnosis counter (B Bus Normal Count)
Clear network dual diagnosis counter
Link Control
Version information [#0 - #2]
The correspondence acquisition of the rotary switch set value
and the card logic number [#0 - #1
Dipswitch value
JTNI/JTGI healthy counter
Station(#mmm) controller mounting information [Mac : #000 -
#255]
- Bit 15-8 : Module type
- Bit 7-0 : Controller mounting presence flag
Station(#mmm) healty counter
Station(#mmm) representation alarm
Station(#mmm) slot(#d) healty counter [Slot: #0 - #7]
Station(#mmm) slot(#d) controller type
Station(#mmm) slot(#d) controller type sub type
Station(#mmm) slot(#d) phase/mode
Station(#mmm) slot(#d) representation alarm
/ #4095]
/ #128]
/ #256]
/ #640]
/ #4095]
/ #2]
Data Type Mode
R/W
VT_UI4 R/W
VT_BOOL R/W
VT_UI4 R/W
VT_UI2 RO
VT_UI2 RO
VT_UI2 RO
VT_UI2 RO
VT_UI2 RO
VT_UI2 RO
VT_UI2 RO
VT_UI2 RO
VT_UI2 RO
VT_UI2 RO
VT_UI2 R/W
VT_UI4 R/W
VT_BOOL R/W
VT_UI4 R/W
VT_UI2 R/W
VT_UI4 R/W
VT_UI4 R/W
VT_UI4 R(Sim)/W
VT_UI4 R(Sim)/W
VT_UI4 R/W
VT_UI4 R/W
VT_UI4 R/W
VT_UI2 R/W
VT_UI4 RO
VT_UI2 R(Sim)/W
VT_UI2 R/W
VT_UI2 R(Sim)/W
VT_UI2 R/W
VT_UI2 R(Sim)/W
VT_UI2 R/W
VT_UI2 R/W
VT_UI2 R/W
VT_UI2 R/W