Aiwa HT-DV1 Operating Instructions Manual page 55

CORRECTIONS
Please read the incorrect descriptions in the Operating
Instructions as follows.
Note:
The page numbers in parentheses are different between
the two versions of the Operating Instructions.
U: page number of the U version for the customers in the
United States
K: page number of the K version for the customers in the
United Kingdom
CAUTION
(U: page 7)
CAUTION
• Lithium battery (CR2025) for the remote control
Replace the battery with Hitachi Maxell, Panasonic,
or Sony, Part No. CR2025 only. Use of another battery
may present a risk of fire or explosion.
The battery may explode if mistreated. Do not
recharge, disassemble or dispose of in fire.
• Do not keep metallic objects such as rings, bracelets,
and keys near the battery. They may cause the
battery to short circuit.
• After removing the battery, be sure to keep it out of
reach of children. If it is swallowed, consult a doctor
immediately.
CAUTION
(U: page 40, K: page 42)
When connecting an AV receiver not equipped with Dolby
Digital decoder using an optical cord, DO NOT set "Digital
Stream" to "DOLBY DIGITAL" in the "Audio Output
Setting" procedure of the setup menu.
Otherwise, merely attempting to play a disc may cause a
screeching noise that could be harmful to your ears and
damage the speakers.
Audio Output Setting
(U: page 47, K: page 49)
Set the audio output of the system according to the type
of other external audio equipment connected to the system.
NOTE
The system outputs only PCM digital signals converted from
DTS bit-stream signals when playing DTS-encoded discs.
• When connecting other external audio equipment to the
AUDIO OUT L/R jacks of the DVD player, you need to
set "Downmix Type" only.
• When connecting an external AV receiver not equipped
with Dolby Digital decoder to the DIGITAL OUT
(OPTICAL) jack of the DVD player, you need not make
any settings.
• When playing DVDs with Dolby Digital sound on an
external AV receiver equipped with Dolby Digital
decoder, set "Digital Stream" to "DOLBY DIGITAL".
CAUTION
(U: page 47, K: page 49)
The same correction as for page 40 (U) or page 42 (K)
above.
dts Output:
(U: pages 47 and 48, K: pages 49 and 50)
Set whether PCM digital signals converted from DTS bit-
stream signals are output from the DIGITAL OUT
(OPTICAL) jack or not.
NOTE
The system cannot output DTS bit-stream signals directly
from the DIGITAL OUT (OPTICAL) jack when playing DTS-
encoded discs.
1 In the SETUP MENU, press i/k repeatedly to
select "Audio Output Setting", then press
ENTER.
2 Press i/k repeatedly to select "dts Output".
3 Press ENTER to select the appropriate setting.
Each time the button is pressed, the setting toggles
between "ON" and "OFF".
ON
PCM digital signals converted from DTS bit-stream
signals are output from the DIGITAL OUT (OPTICAL)
jack.
OFF
PCM digital signals converted from DTS bit-stream
signals are not output from the DIGITAL OUT
(OPTICAL) jack.
4 Press vRETURN to return to the previous
screen or press SETUP to exit the setup menu.
Speaker Setting:
(U: page 48, K: page 50)
Set the audio balance among the speakers from the
listening position.
Based on the distance setting from the listening position,
the system calculates and adjusts the delay times of the
respective speakers so that the sounds from them are
centered at the listening position.
Test Sound:
(U: page 49, K: page 51)
A test tone is generated from each speaker allowing you
to check the audio balance among the speakers from the
listening position. If the volume levels of the speakers are
noticeably different from each other at the listening
position, adjust the position or direction of the speakers.
HT-DV1 [ U ] [ K ]